1# $FreeBSD$ 2# 3# Example configuration file for bsnmpd(1). 4# 5 6# 7# Set some common variables 8# 9location := "Room 200" 10contact := "sysmeister@example.com" 11system := 1 # FreeBSD 12traphost := localhost 13trapport := 162 14 15# 16# Set the SNMP engine ID. 17# 18# The snmpEngineID object required from the SNMPv3 Framework. If not explicitly set via 19# this configuration file, an ID is assigned based on the value of the 20# kern.hostid variable 21# engine := 0x80:0x10:0x08:0x10:0x80:0x25 22# snmpEngineID = $(engine) 23 24# Change this! 25read := "public" 26# Uncomment begemotSnmpdCommunityString.0.2 below that sets the community 27# string to enable write access. 28write := "geheim" 29trap := "mytrap" 30 31# 32# Declarations for SNMP-USER-BASED-SM-MIB authentication and privacy options 33# 34 35NoAuthProtocol := 1.3.6.1.6.3.10.1.1.1 36HMACMD5AuthProtocol := 1.3.6.1.6.3.10.1.1.2 37HMACSHAAuthProtocol := 1.3.6.1.6.3.10.1.1.3 38NoPrivProtocol := 1.3.6.1.6.3.10.1.2.1 39DESPrivProtocol := 1.3.6.1.6.3.10.1.2.2 40AesCfb128Protocol := 1.3.6.1.6.3.10.1.2.4 41 42# 43# Enumerations from SNMP-FRAMEWORK-MIB 44# 45 46# Security models 47securityModelAny := 0 48securityModelSNMPv1 := 1 49securityModelSNMPv2c := 2 50securityModelUSM := 3 51 52# Message Processing models 53MPmodelSNMPv1 := 0 54MPmodelSNMPv2c := 1 55MPmodelSNMPv3 := 3 56 57# Security levels 58noAuthNoPriv := 1 59authNoPriv := 2 60authPriv := 3 61 62 63# SNMPv3 USM User definition 64# 65# The localized hex password for a user may be obtained by setting SNMPUSER, SNMPPASSWD, 66# SNMPAUTH and SNMPPRIV environment variables to the desired parameters and invoking 67# 'bsnmpget -v 3 -D -K -o verbose' against the running bsnmpd(1). For other 68# usages refer to the bsnmpget(1) manual page. The following lines define a user "bsnmp" 69# with a private password "bsnmptest", localized for the above engine ID. 70# 71#user1 := "bsnmp" 72#user1passwd := 0x22:0x98:0x1a:0x6e:0x39:0x93:0x16:0x5e:0x6a:0x21:0x1b:0xd8:0xa9:0x81:0x31:0x05:0x16:0x33:0x38:0x60 73 74# 75# Configuration 76# 77%snmpd 78begemotSnmpdDebugDumpPdus = 2 79begemotSnmpdDebugSyslogPri = 7 80 81# 82# Set the read and write communities. 83# 84# The default value of the community strings is NULL (note, that this is 85# different from the empty string). This disables both read and write access. 86# To enable read access only the read community string must be set. Setting 87# the write community string enables both read and write access with that 88# string. 89# 90# Be sure to understand the security implications of SNMPv2 - the community 91# strings are readable on the wire! 92# 93begemotSnmpdCommunityString.0.1 = $(read) 94# begemotSnmpdCommunityString.0.2 = $(write) 95begemotSnmpdCommunityDisable = 1 96 97# open standard SNMP ports 98begemotSnmpdPortStatus.0.0.0.0.161 = 1 99 100# open a unix domain socket 101begemotSnmpdLocalPortStatus."/var/run/snmpd.sock" = 1 102begemotSnmpdLocalPortType."/var/run/snmpd.sock" = 4 103 104# send traps to the traphost 105begemotTrapSinkStatus.[$(traphost)].$(trapport) = 4 106begemotTrapSinkVersion.[$(traphost)].$(trapport) = 2 107begemotTrapSinkComm.[$(traphost)].$(trapport) = $(trap) 108 109sysContact = $(contact) 110sysLocation = $(location) 111sysObjectId = 1.3.6.1.4.1.12325.1.1.2.1.$(system) 112 113snmpEnableAuthenTraps = 2 114 115# 116# SNMPv3 User-based security module - must be loaded for SNMPv3 USM 117# 118#begemotSnmpdModulePath."usm" = "/usr/lib/snmp_usm.so" 119 120# 121# SNMPv3 USM User definition. 122# 123 124#%usm 125 126# 127# The following block creates a user with name "bsnmp" and sets privacy 128# and encryption options to SHA256 message digests and AES encryption 129# for this user. 130# 131# usmUserStatus.$(engine).$(user1) = 5 132# usmUserAuthProtocol.$(engine).$(user1) = $(HMACSHAAuthProtocol) 133# usmUserAuthKeyChange.$(engine).$(user1) = $(user1passwd) 134# usmUserPrivProtocol.$(engine).$(user1) = $(AesCfb128Protocol) 135# usmUserPrivKeyChange.$(engine).$(user1) = $(user1passwd) 136# usmUserStatus.$(engine).$(user1) = 1 137# 138 139# 140# The following block creates a user with name "public" with no authentication 141# or encryption options. 142# 143# usmUserStatus.$(engine).$(read) = 5 144# usmUserAuthProtocol.$(engine).$(read) = $(NoAuthProtocol) 145# usmUserPrivProtocol.$(engine).$(read) = $(NoPrivProtocol) 146# usmUserStatus.$(engine).$(read) = 1 147# 148 149# 150# SNMPv3 View-based Access Control module 151# 152#begemotSnmpdModulePath."vacm" = "/usr/lib/snmp_vacm.so" 153 154# 155# Definition of view-based access control entries. 156# 157#%vacm 158 159# Definition of a SNMPv1 group 160# vacmSecurityToGroupStatus.$(securityModelSNMPv1).$(read) = 4 161# vacmGroupName.$(securityModelSNMPv1).$(read) = $(read) 162 163# Definition of SNMPv2 group 164# vacmSecurityToGroupStatus.$(securityModelSNMPv2c).$(write) = 4 165# vacmGroupName.$(securityModelSNMPv2c).$(write) = $(write) 166 167# Definition of SNMPv3 group with users "bsnmp" and "public" 168# vacmSecurityToGroupStatus.$(securityModelUSM).$(user1) = 4 169# vacmGroupName.$(securityModelUSM).$(user1) = $(write) 170# vacmSecurityToGroupStatus.$(securityModelUSM).$(read) = 4 171# vacmGroupName.$(securityModelUSM).$(read) = $(write) 172 173# 174# The OID of the .iso.org.dod.internet subtree 175# 176# internetoid := 1.3.6.1 177# internetoidlen := 4 178 179# 180# Definitions of two views 181# 182# vacmViewTreeFamilyStatus."internet".$(internetoidlen).$(internetoid) = 4 183# vacmViewTreeFamilyStatus."restricted".$(internetoidlen).$(internetoid) = 4 184 185# 186# Access control 187# 188 189# 190# Read-only access for SNMPv1 users 191# 192# vacmAccessStatus.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = 4 193# vacmAccessReadViewName.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = "internet" 194 195# 196# Read-write access for SNMPv2 users 197# 198# vacmAccessStatus.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = 4 199# vacmAccessReadViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 200# vacmAccessWriteViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 201 202# 203# Read-write-notify access for SNMPv3 USM users with noAuthNoPriv 204# 205# vacmAccessStatus.$(write)."".3.$(noAuthNoPriv) = 4 206# vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 207# vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 208# vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 209 210# 211#Read-write-notify access to restricted for SNMPv3 USM users with authPriv 212# 213# vacmAccessStatus.$(write)."".3.$(authPriv) = 4 214# vacmAccessReadViewName.$(write)."".3.$(authPriv) = "restricted" 215# vacmAccessWriteViewName.$(write)."".3.$(authPriv) = "restricted" 216# vacmAccessNotifyViewName.$(write)."".3.$(authPriv) = "restricted" 217 218# 219# SNMPv3 Notification Targets 220# 221# begemotSnmpdModulePath."target" = "/usr/lib/snmp_target.so" 222 223#%target 224# Send notifications to target tag "test" 225# tag := "test" 226# snmpNotifyRowStatus.$(tag) = 4 227# snmpNotifyTag.$(tag) = $(tag) 228 229# tagremote := "testremote" 230# snmpNotifyRowStatus.$(tagremote) = 4 231# snmpNotifyTag.$(tagremote) = $(tagremote) 232 233# 234# Specify the target parameters for the notifications - send with the credentials 235# of user "bsnmp" 236# 237# snmpTargetParamsRowStatus.$(tag) = 5 238# snmpTargetParamsMPModel.$(tag) = $(MPmodelSNMPv3) 239# snmpTargetParamsSecurityModel.$(tag) = $(securityModelUSM) 240# snmpTargetParamsSecurityName.$(tag) = $(user1) 241# snmpTargetParamsSecurityLevel.$(tag) = $(authPriv) 242# snmpTargetParamsRowStatus.$(tag) = 1 243 244# 245# Define the notifications' target address - port 162 on localhost 246# 247# snmpTargetAddrRowStatus.$(tag) = 5 248# snmpTargetAddrTAddress.$(tag) = 0x7f:0x0:0x0:0x1:0x0:0xa2 249# snmpTargetAddrTagList.$(tag) = "test notification" 250# snmpTargetAddrParams.$(tag) = $(tag) 251# snmpTargetAddrRowStatus.$(tag) = 1 252 253# 254# Define the notifications' target address - port 162 on 10.0.0.1 255# 256# snmpTargetAddrRowStatus.$(tagremote) = 5 257# snmpTargetAddrTAddress.$(tagremote) = 0x0a:0x00:0x00:0x1:0x0:0xa2 258# snmpTargetAddrTagList.$(tagremote) = $(tagremote) 259# snmpTargetAddrParams.$(tagremote) = $(tag) 260# snmpTargetAddrRowStatus.$(tagremote) = 1 261 262# 263# Load MIB-2 module 264# 265begemotSnmpdModulePath."mibII" = "/usr/lib/snmp_mibII.so" 266 267# Force a polling rate for the 64-bit interface counters in case 268# the automatic computation is wrong (which may be the case if an interface 269# announces the wrong bit rate via its MIB). 270#%mibII 271#begemotIfForcePoll = 2000 272 273 274# Netgraph module 275# 276#begemotSnmpdModulePath."netgraph" = "/usr/lib/snmp_netgraph.so" 277# 278#%netgraph 279#begemotNgControlNodeName = "snmpd" 280 281# 282# pf(4) module 283# 284#begemotSnmpdModulePath."pf" = "/usr/lib/snmp_pf.so" 285 286# 287# Host resources module 288# This requires the mibII module. 289# 290#begemotSnmpdModulePath."hostres" = "/usr/lib/snmp_hostres.so" 291 292# 293# Bridge module 294# This requires the mibII module. 295# 296#begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so" 297 298# 299# Wireless module 300# This requires the mibII module. 301# 302#begemotSnmpdModulePath."wlan" = "/usr/lib/snmp_wlan.so" 303