1/*- 2 * Copyright (c) 2012 3 * Ben Gray <bgray@freebsd.org>. 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND 16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 18 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE 19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 25 * SUCH DAMAGE. 26 * 27 * $FreeBSD$ 28 */ 29#ifndef _IF_SMSCREG_H_ 30#define _IF_SMSCREG_H_ 31 32/* 33 * Definitions for the SMSC LAN9514 and LAN9514 USB to ethernet controllers. 34 * 35 * This information was gleaned from the SMSC driver in the linux kernel, where 36 * it is Copyrighted (C) 2007-2008 SMSC. 37 * 38 */ 39 40/** 41 * TRANSMIT FRAMES 42 * --------------- 43 * Tx frames are prefixed with an 8-byte header which describes the frame 44 * 45 * 4 bytes 4 bytes variable 46 * +------------+------------+--- . . . . . . . . . . . . ---+ 47 * | TX_CTRL_0 | TX_CTRL_1 | Ethernet frame data | 48 * +------------+------------+--- . . . . . . . . . . . . ---+ 49 * 50 * Where the headers have the following fields: 51 * 52 * TX_CTRL_0 <20:16> Data offset 53 * TX_CTRL_0 <13> First segment of frame indicator 54 * TX_CTRL_0 <12> Last segment of frame indicator 55 * TX_CTRL_0 <10:0> Buffer size (?) 56 * 57 * TX_CTRL_1 <14> Perform H/W checksuming on IP packets 58 * TX_CTRL_1 <13> Disable automatic ethernet CRC generation 59 * TX_CTRL_1 <12> Disable padding (?) 60 * TX_CTRL_1 <10:0> Packet byte length 61 * 62 */ 63#define SMSC_TX_CTRL_0_OFFSET(x) (((x) & 0x1FUL) << 16) 64#define SMSC_TX_CTRL_0_FIRST_SEG (0x1UL << 13) 65#define SMSC_TX_CTRL_0_LAST_SEG (0x1UL << 12) 66#define SMSC_TX_CTRL_0_BUF_SIZE(x) ((x) & 0x000007FFUL) 67 68#define SMSC_TX_CTRL_1_CSUM_ENABLE (0x1UL << 14) 69#define SMSC_TX_CTRL_1_CRC_DISABLE (0x1UL << 13) 70#define SMSC_TX_CTRL_1_PADDING_DISABLE (0x1UL << 12) 71#define SMSC_TX_CTRL_1_PKT_LENGTH(x) ((x) & 0x000007FFUL) 72 73/** 74 * RECEIVE FRAMES 75 * -------------- 76 * Rx frames are prefixed with an 4-byte status header which describes any 77 * errors with the frame as well as things like the length 78 * 79 * 4 bytes variable 80 * +------------+--- . . . . . . . . . . . . ---+ 81 * | RX_STAT | Ethernet frame data | 82 * +------------+--- . . . . . . . . . . . . ---+ 83 * 84 * Where the status header has the following fields: 85 * 86 * RX_STAT <30> Filter Fail 87 * RX_STAT <29:16> Frame Length 88 * RX_STAT <15> Error Summary 89 * RX_STAT <13> Broadcast Frame 90 * RX_STAT <12> Length Error 91 * RX_STAT <11> Runt Frame 92 * RX_STAT <10> Multicast Frame 93 * RX_STAT <7> Frame too long 94 * RX_STAT <6> Collision Seen 95 * RX_STAT <5> Frame Type 96 * RX_STAT <4> Receive Watchdog 97 * RX_STAT <3> Mii Error 98 * RX_STAT <2> Dribbling 99 * RX_STAT <1> CRC Error 100 * 101 */ 102#define SMSC_RX_STAT_FILTER_FAIL (0x1UL << 30) 103#define SMSC_RX_STAT_FRM_LENGTH(x) (((x) >> 16) & 0x3FFFUL) 104#define SMSC_RX_STAT_ERROR (0x1UL << 15) 105#define SMSC_RX_STAT_BROADCAST (0x1UL << 13) 106#define SMSC_RX_STAT_LENGTH_ERROR (0x1UL << 12) 107#define SMSC_RX_STAT_RUNT (0x1UL << 11) 108#define SMSC_RX_STAT_MULTICAST (0x1UL << 10) 109#define SMSC_RX_STAT_FRM_TO_LONG (0x1UL << 7) 110#define SMSC_RX_STAT_COLLISION (0x1UL << 6) 111#define SMSC_RX_STAT_FRM_TYPE (0x1UL << 5) 112#define SMSC_RX_STAT_WATCHDOG (0x1UL << 4) 113#define SMSC_RX_STAT_MII_ERROR (0x1UL << 3) 114#define SMSC_RX_STAT_DRIBBLING (0x1UL << 2) 115#define SMSC_RX_STAT_CRC_ERROR (0x1UL << 1) 116 117/** 118 * REGISTERS 119 * 120 */ 121#define SMSC_ID_REV 0x000 122#define SMSC_INTR_STATUS 0x008 123#define SMSC_RX_CFG 0x00C 124#define SMSC_TX_CFG 0x010 125#define SMSC_HW_CFG 0x014 126#define SMSC_PM_CTRL 0x020 127#define SMSC_LED_GPIO_CFG 0x024 128#define SMSC_GPIO_CFG 0x028 129#define SMSC_AFC_CFG 0x02C 130#define SMSC_EEPROM_CMD 0x030 131#define SMSC_EEPROM_DATA 0x034 132#define SMSC_BURST_CAP 0x038 133#define SMSC_GPIO_WAKE 0x064 134#define SMSC_INTR_CFG 0x068 135#define SMSC_BULK_IN_DLY 0x06C 136#define SMSC_MAC_CSR 0x100 137#define SMSC_MAC_ADDRH 0x104 138#define SMSC_MAC_ADDRL 0x108 139#define SMSC_HASHH 0x10C 140#define SMSC_HASHL 0x110 141#define SMSC_MII_ADDR 0x114 142#define SMSC_MII_DATA 0x118 143#define SMSC_FLOW 0x11C 144#define SMSC_VLAN1 0x120 145#define SMSC_VLAN2 0x124 146#define SMSC_WUFF 0x128 147#define SMSC_WUCSR 0x12C 148#define SMSC_COE_CTRL 0x130 149 150/* ID / Revision register */ 151#define SMSC_ID_REV_CHIP_ID_MASK 0xFFFF0000UL 152#define SMSC_ID_REV_CHIP_REV_MASK 0x0000FFFFUL 153 154#define SMSC_RX_FIFO_FLUSH (0x1UL << 0) 155 156#define SMSC_TX_CFG_ON (0x1UL << 2) 157#define SMSC_TX_CFG_STOP (0x1UL << 1) 158#define SMSC_TX_CFG_FIFO_FLUSH (0x1UL << 0) 159 160#define SMSC_HW_CFG_BIR (0x1UL << 12) 161#define SMSC_HW_CFG_LEDB (0x1UL << 11) 162#define SMSC_HW_CFG_RXDOFF (0x3UL << 9) /* RX pkt alignment */ 163#define SMSC_HW_CFG_DRP (0x1UL << 6) 164#define SMSC_HW_CFG_MEF (0x1UL << 5) 165#define SMSC_HW_CFG_LRST (0x1UL << 3) /* Lite reset */ 166#define SMSC_HW_CFG_PSEL (0x1UL << 2) 167#define SMSC_HW_CFG_BCE (0x1UL << 1) 168#define SMSC_HW_CFG_SRST (0x1UL << 0) 169 170#define SMSC_PM_CTRL_PHY_RST (0x1UL << 4) /* PHY reset */ 171 172#define SMSC_LED_GPIO_CFG_SPD_LED (0x1UL << 24) 173#define SMSC_LED_GPIO_CFG_LNK_LED (0x1UL << 20) 174#define SMSC_LED_GPIO_CFG_FDX_LED (0x1UL << 16) 175 176/* Hi watermark = 15.5Kb (~10 mtu pkts) */ 177/* low watermark = 3k (~2 mtu pkts) */ 178/* backpressure duration = ~ 350us */ 179/* Apply FC on any frame. */ 180#define AFC_CFG_DEFAULT (0x00F830A1) 181 182#define SMSC_EEPROM_CMD_BUSY (0x1UL << 31) 183#define SMSC_EEPROM_CMD_MASK (0x7UL << 28) 184#define SMSC_EEPROM_CMD_READ (0x0UL << 28) 185#define SMSC_EEPROM_CMD_WRITE (0x3UL << 28) 186#define SMSC_EEPROM_CMD_ERASE (0x5UL << 28) 187#define SMSC_EEPROM_CMD_RELOAD (0x7UL << 28) 188#define SMSC_EEPROM_CMD_TIMEOUT (0x1UL << 10) 189#define SMSC_EEPROM_CMD_ADDR_MASK 0x000001FFUL 190 191/* MAC Control and Status Register */ 192#define SMSC_MAC_CSR_RCVOWN (0x1UL << 23) /* Half duplex */ 193#define SMSC_MAC_CSR_LOOPBK (0x1UL << 21) /* Loopback */ 194#define SMSC_MAC_CSR_FDPX (0x1UL << 20) /* Full duplex */ 195#define SMSC_MAC_CSR_MCPAS (0x1UL << 19) /* Multicast mode */ 196#define SMSC_MAC_CSR_PRMS (0x1UL << 18) /* Promiscuous mode */ 197#define SMSC_MAC_CSR_INVFILT (0x1UL << 17) /* Inverse filtering */ 198#define SMSC_MAC_CSR_PASSBAD (0x1UL << 16) /* Pass on bad frames */ 199#define SMSC_MAC_CSR_HPFILT (0x1UL << 13) /* Hash filtering */ 200#define SMSC_MAC_CSR_BCAST (0x1UL << 11) /* Broadcast */ 201#define SMSC_MAC_CSR_TXEN (0x1UL << 3) /* TX enable */ 202#define SMSC_MAC_CSR_RXEN (0x1UL << 2) /* RX enable */ 203 204/* Interrupt control register */ 205#define SMSC_INTR_NTEP (0x1UL << 31) 206#define SMSC_INTR_MACRTO (0x1UL << 19) 207#define SMSC_INTR_TX_STOP (0x1UL << 17) 208#define SMSC_INTR_RX_STOP (0x1UL << 16) 209#define SMSC_INTR_PHY_INT (0x1UL << 15) 210#define SMSC_INTR_TXE (0x1UL << 14) 211#define SMSC_INTR_TDFU (0x1UL << 13) 212#define SMSC_INTR_TDFO (0x1UL << 12) 213#define SMSC_INTR_RXDF (0x1UL << 11) 214#define SMSC_INTR_GPIOS 0x000007FFUL 215 216/* Phy MII interface register */ 217#define SMSC_MII_WRITE (0x1UL << 1) 218#define SMSC_MII_READ (0x0UL << 1) 219#define SMSC_MII_BUSY (0x1UL << 0) 220 221/* H/W checksum register */ 222#define SMSC_COE_CTRL_TX_EN (0x1UL << 16) /* Tx H/W csum enable */ 223#define SMSC_COE_CTRL_RX_MODE (0x1UL << 1) 224#define SMSC_COE_CTRL_RX_EN (0x1UL << 0) /* Rx H/W csum enable */ 225 226/* Registers on the phy, accessed via MII/MDIO */ 227#define SMSC_PHY_INTR_STAT (29) 228#define SMSC_PHY_INTR_MASK (30) 229 230#define SMSC_PHY_INTR_ENERGY_ON (0x1U << 7) 231#define SMSC_PHY_INTR_ANEG_COMP (0x1U << 6) 232#define SMSC_PHY_INTR_REMOTE_FAULT (0x1U << 5) 233#define SMSC_PHY_INTR_LINK_DOWN (0x1U << 4) 234 235/* USB Vendor Requests */ 236#define SMSC_UR_WRITE_REG 0xA0 237#define SMSC_UR_READ_REG 0xA1 238#define SMSC_UR_GET_STATS 0xA2 239 240#define SMSC_CONFIG_INDEX 0 /* config number 1 */ 241#define SMSC_IFACE_IDX 0 242 243/* 244 * USB endpoints. 245 */ 246enum { 247 SMSC_BULK_DT_RD, 248 SMSC_BULK_DT_WR, 249 /* the LAN9514 device does support interrupt endpoints, however I couldn't 250 * get then to work reliably and since they are unneeded (poll the mii 251 * status) they are unused. 252 * SMSC_INTR_DT_WR, 253 * SMSC_INTR_DT_RD, 254 */ 255 SMSC_N_TRANSFER, 256}; 257 258struct smsc_softc { 259 struct usb_ether sc_ue; 260 struct mtx sc_mtx; 261 struct usb_xfer *sc_xfer[SMSC_N_TRANSFER]; 262 int sc_phyno; 263 264 /* The following stores the settings in the mac control (MAC_CSR) register */ 265 uint32_t sc_mac_csr; 266 uint32_t sc_rev_id; 267 268 uint32_t sc_flags; 269#define SMSC_FLAG_LINK 0x0001 270#define SMSC_FLAG_LAN9514 0x1000 /* LAN9514 */ 271}; 272 273#define SMSC_LOCK(_sc) mtx_lock(&(_sc)->sc_mtx) 274#define SMSC_UNLOCK(_sc) mtx_unlock(&(_sc)->sc_mtx) 275#define SMSC_LOCK_ASSERT(_sc, t) mtx_assert(&(_sc)->sc_mtx, t) 276 277#endif /* _IF_SMSCREG_H_ */ 278