ARM: renesas: Rename rmobile.h to renesas.h

Rename rmobile.h to renesas.h because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.

Use the following command to perform the rename:

"
$ git grep -l 'include.*rmobile.h' | \
xargs -I {} sed -i '/include.*rmobile.h/ s@rmobile.h@renesas.h@g' {}
"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>

Convert CONFIG_SH_GPIO_PFC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SH_GPIO_PFC
CONFIG_TMU_TIMER

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_TIMER_COUNTS_DOWN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_TARGET to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_TARGET

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_BOOTM_NETBSD et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM

This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD

Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

This converts the following to Kconfig:
CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: rmobile: rcar-gen2: Activate bootm_size

Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>

ARM: rmobile: Convert Gen2 Stout, Porter, Silk to DM_SPI{,_FLASH}

Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Repair TMU clock on Gen2

The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

ARM: rmobile: Repair TMU clock on Gen2

The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

sh: tmu: Zap get_tbclk and timer_read_counter

Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: rmobile: Point load address to more sane area on Gen2

Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Enable MTD partitioning on Gen2 with SF

Enable MTD partitioning support on Gen2 boards with SPI NORs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Enable autocompletion on Gen2

This makes the shell so much more pleasant to use, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Convert R8A7791 Porter board to DM and DT

Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

fs: fat: Drop CONFIG_SUPPORT_VFAT

fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

include/configs: remove default values of CONFIG_SYS_BARGSIZE

CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Drop CONFIG_CMD_DFL

This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD

Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common, kconfig: move VERSION_VARIABLE to Kconfig

move VERSION_VARIABLE from board config file into a
Kconfig option.

Signed-off-by: Heiko Schocher <hs@denx.de>

ARM: Move SYS_CACHELINE_SIZE over to Kconfig

This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

armv7: add cacheline sizes where missing

Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

malloc_f: enable SYS_MALLOC_F by default if DM is on

This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>

arm: rmobile: koelsch: Migrate serial driver to drivers model

This adds drivers model support of serial port to Koelsch board,
and migrate serial port to drivers model.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: rcar: Add support ext2 and ext4 file system

Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: configs: Collect up common part of config for R-Car SoCs

The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Convert CONFIG_SH_GPIO_PFC et al to Kconfig

This converts the following to Kconfig:
CONFIG_SH_GPIO_PFC
CONFIG_TMU_TIMER

Signed-off-by: Tom Rini <trini@konsulko.com>

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_TIMER_COUNTS_DOWN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_TARGET to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_TARGET

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_BOOTM_NETBSD et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM

This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD

Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

This converts the following to Kconfig:
CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: rmobile: rcar-gen2: Activate bootm_size

Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>

ARM: rmobile: Convert Gen2 Stout, Porter, Silk to DM_SPI{,_FLASH}

Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Repair TMU clock on Gen2

The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

ARM: rmobile: Repair TMU clock on Gen2

The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

sh: tmu: Zap get_tbclk and timer_read_counter

Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: rmobile: Point load address to more sane area on Gen2

Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Enable MTD partitioning on Gen2 with SF

Enable MTD partitioning support on Gen2 boards with SPI NORs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Enable autocompletion on Gen2

This makes the shell so much more pleasant to use, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Convert R8A7791 Porter board to DM and DT

Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

fs: fat: Drop CONFIG_SUPPORT_VFAT

fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

include/configs: remove default values of CONFIG_SYS_BARGSIZE

CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Drop CONFIG_CMD_DFL

This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD

Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common, kconfig: move VERSION_VARIABLE to Kconfig

move VERSION_VARIABLE from board config file into a
Kconfig option.

Signed-off-by: Heiko Schocher <hs@denx.de>

ARM: Move SYS_CACHELINE_SIZE over to Kconfig

This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

armv7: add cacheline sizes where missing

Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

malloc_f: enable SYS_MALLOC_F by default if DM is on

This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>

arm: rmobile: koelsch: Migrate serial driver to drivers model

This adds drivers model support of serial port to Koelsch board,
and migrate serial port to drivers model.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: rcar: Add support ext2 and ext4 file system

Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: configs: Collect up common part of config for R-Car SoCs

The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SPL_TARGET to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_TARGET

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_BOOTM_NETBSD et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM

This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD

Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

This converts the following to Kconfig:
CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: rmobile: rcar-gen2: Activate bootm_size

Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>

ARM: rmobile: Convert Gen2 Stout, Porter, Silk to DM_SPI{,_FLASH}

Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Repair TMU clock on Gen2

The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

ARM: rmobile: Repair TMU clock on Gen2

The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

sh: tmu: Zap get_tbclk and timer_read_counter

Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: rmobile: Point load address to more sane area on Gen2

Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Enable MTD partitioning on Gen2 with SF

Enable MTD partitioning support on Gen2 boards with SPI NORs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Enable autocompletion on Gen2

This makes the shell so much more pleasant to use, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Convert R8A7791 Porter board to DM and DT

Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

fs: fat: Drop CONFIG_SUPPORT_VFAT

fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

include/configs: remove default values of CONFIG_SYS_BARGSIZE

CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Drop CONFIG_CMD_DFL

This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD

Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common, kconfig: move VERSION_VARIABLE to Kconfig

move VERSION_VARIABLE from board config file into a
Kconfig option.

Signed-off-by: Heiko Schocher <hs@denx.de>

ARM: Move SYS_CACHELINE_SIZE over to Kconfig

This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

armv7: add cacheline sizes where missing

Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

malloc_f: enable SYS_MALLOC_F by default if DM is on

This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>

arm: rmobile: koelsch: Migrate serial driver to drivers model

This adds drivers model support of serial port to Koelsch board,
and migrate serial port to drivers model.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: rcar: Add support ext2 and ext4 file system

Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: configs: Collect up common part of config for R-Car SoCs

The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Convert CONFIG_SPL_TARGET to Kconfig

This converts the following to Kconfig:
CONFIG_SPL_TARGET

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_PBSIZE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_BOOTM_NETBSD et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM

This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD

Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

This converts the following to Kconfig:
CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: rmobile: rcar-gen2: Activate bootm_size

Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>

ARM: rmobile: Convert Gen2 Stout, Porter, Silk to DM_SPI{,_FLASH}

Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Repair TMU clock on Gen2

The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

ARM: rmobile: Repair TMU clock on Gen2

The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

sh: tmu: Zap get_tbclk and timer_read_counter

Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: rmobile: Point load address to more sane area on Gen2

Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Enable MTD partitioning on Gen2 with SF

Enable MTD partitioning support on Gen2 boards with SPI NORs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Enable autocompletion on Gen2

This makes the shell so much more pleasant to use, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Convert R8A7791 Porter board to DM and DT

Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

fs: fat: Drop CONFIG_SUPPORT_VFAT

fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

include/configs: remove default values of CONFIG_SYS_BARGSIZE

CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate FS_FAT / FAT_WRITE

Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig: Drop CONFIG_CMD_DFL

This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

Kconfig: Migrate CONFIG_BAUDRATE

Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD

Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig

This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert CONFIG_SYS_CONSOLE_INFO_QUIET to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_CONSOLE_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_ENV_OVERWRITE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

common: Add DISPLAY_BOARDINFO

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common/Kconfig: Add DISPLAY_CPUINFO

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

common, kconfig: move VERSION_VARIABLE to Kconfig

move VERSION_VARIABLE from board config file into a
Kconfig option.

Signed-off-by: Heiko Schocher <hs@denx.de>

ARM: Move SYS_CACHELINE_SIZE over to Kconfig

This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>

common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

configs: Re-sync with cmd/Kconfig

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Re-sync almost all of cmd/Kconfig

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_OF_LIBFDT to Kconfig

Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>

armv7: add cacheline sizes where missing

Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

net: Move the CMD_NET config to defconfigs

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

malloc_f: enable SYS_MALLOC_F by default if DM is on

This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>

arm: rmobile: koelsch: Migrate serial driver to drivers model

This adds drivers model support of serial port to Koelsch board,
and migrate serial port to drivers model.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: rcar: Add support ext2 and ext4 file system

Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

arm: rmobile: configs: Collect up common part of config for R-Car SoCs

The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Convert CONFIG_SYS_MONITOR_BASE to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE

Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish converting CONFIG_BOOTM_NETBSD et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTM_NETBSD
CONFIG_BOOTM_RTEMS
CONFIG_DESIGNWARE_WATCHDOG
CONFIG_DISPLAY_CPUINFO
CONFIG_DM_ETH
CONFIG_DM_MMC
CONFIG_DM_REGULATOR
CONFIG_DM_SPI
CONFIG_DM_SPI_FLASH
CONFIG_ISO_PARTITION
CONFIG_OF_SEPARATE
CONFIG_SPI_FLASH_WINBOND
CONFIG_SPL_ETH
CONFIG_TIMER
CONFIG_USB_DWC3
CONFIG_USB_DWC3_GADGET
CONFIG_USB_DWC3_OMAP
CONFIG_USB_DWC3_PHY_OMAP
CONFIG_USB_EHCI_TEGRA
CONFIG_USB_GADGET_DOWNLOAD
CONFIG_USB_GADGET_DUALSPEED
CONFIG_USB_GADGET_MANUFACTURER
CONFIG_USB_GADGET_PRODUCT_NUM
CONFIG_USB_GADGET_VBUS_DRAW
CONFIG_USB_GADGET_VENDOR_NUM

This catches a number of cases where board config files were #undef
various CONFIG options when building SPL, and that doesn't work. Clean
up the related comments as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig

In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>

arm: Disable ATAGs support

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_SYS_MALLOC_LEN to Kconfig

This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ENV_OVERWRITE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

env: Finish migration of common ENV options

- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result. The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED. This seems like the most likely use, historically, of
the variable, but it was not used. Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD

Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

Convert CONFIG_SHOW_BOOT_PROGRESS to Kconfig

This converts the following to Kconfig:
CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

ARM: rmobile: rcar-gen2: Activate bootm_size

Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>

ARM: rmobile: Convert Gen2 Stout, Porter, Silk to DM_SPI{,_FLASH}

Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Repair TMU clock on Gen2

The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

ARM: rmobile: Repair TMU clock on Gen2

The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

sh: tmu: Zap get_tbclk and timer_read_counter

Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: rmobile: Point load address to more sane area on Gen2

Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Enable MTD partitioning on Gen2 with SF

Enable MTD partitioning support on Gen2 boards with SPI NORs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Build u-boot-spl.srec on Gen2

The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: rmobile: Enable autocompletion on Gen2

This makes the shell so much more pleasant to use, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ARM: rmobile: Convert R8A7791 Porter board to DM and DT

Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

fs: fat: Drop CONFIG_SUPPORT_VFAT

fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

fs: Migrate ext4 to Kconfig

Migrate the following symbols to Kconfig:

CONFIG_FS_EXT4
CONFIG_EXT4_WRITE

The definitions in config_fallbacks.h can now be expressed in Kconfig.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

include/configs: remove default values of CONFIG_SYS_BARGSIZE

CONFIG_SYS_BARGSIZE is already defined to 512 in common/image.c when
not defined. Therefore, there is no point in having board
configuration files define it to 512.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: drop default definitions of CONFIG_SYS_MAXARGS

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_CMD_SDRAM to Kconfig

This converts the following to Kconfig:
CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>