#
fb89b69a |
|
04-Aug-2023 |
Nicolas Frattaroli <frattaroli.nicolas@gmail.com> |
net: phy: motorcomm: Add support for YT8511 PHY The YT8511 ethernet PHYs can be found on e.g. the SOQuartz or the Quartz64. Add rudimentary support for them. Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com> |
#
e92ed065 |
|
15-Jun-2023 |
Yanhong Wang <yanhong.wang@starfivetech.com> |
net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have verified the driver on StarFive VisionFive2 board. Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b6fcab07 |
|
19-Mar-2023 |
Marek Vasut <marek.vasut+renesas@mailbox.org> |
net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux Pull Marvell 10G PHY driver from Linux 6.1.y as of commit d6d29292640d3 ("net: phy: marvell10g: select host interface configuration") and heavily adapt to match U-Boot PHY framework. Support for hwmon is removed as is much other functionality which could not be tested, this results in much simpler driver which can only bring the PHY up and set MAC type. Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
e6c5205d |
|
22-Feb-2023 |
Simon Glass <sjg@chromium.org> |
net: Add an SPL config for atheros Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split config. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
bd22bde9 |
|
10-Jan-2023 |
Tom Rini <trini@konsulko.com> |
net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move the comment from code to the help to explain what this does. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f6301702 |
|
27-Nov-2022 |
Tom Rini <trini@konsulko.com> |
net: Remove extraneous dependencies With DM_ETH being required now for all drivers, we don't need this listed on individual drivers as well. Signed-off-by: Tom Rini <trini@konsulko.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.prasad.paladugu@amd.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e92ed065 |
|
15-Jun-2023 |
Yanhong Wang <yanhong.wang@starfivetech.com> |
net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have verified the driver on StarFive VisionFive2 board. Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b6fcab07 |
|
19-Mar-2023 |
Marek Vasut <marek.vasut+renesas@mailbox.org> |
net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux Pull Marvell 10G PHY driver from Linux 6.1.y as of commit d6d29292640d3 ("net: phy: marvell10g: select host interface configuration") and heavily adapt to match U-Boot PHY framework. Support for hwmon is removed as is much other functionality which could not be tested, this results in much simpler driver which can only bring the PHY up and set MAC type. Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
e6c5205d |
|
22-Feb-2023 |
Simon Glass <sjg@chromium.org> |
net: Add an SPL config for atheros Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split config. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
bd22bde9 |
|
10-Jan-2023 |
Tom Rini <trini@konsulko.com> |
net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move the comment from code to the help to explain what this does. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f6301702 |
|
27-Nov-2022 |
Tom Rini <trini@konsulko.com> |
net: Remove extraneous dependencies With DM_ETH being required now for all drivers, we don't need this listed on individual drivers as well. Signed-off-by: Tom Rini <trini@konsulko.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.prasad.paladugu@amd.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b6fcab07 |
|
19-Mar-2023 |
Marek Vasut <marek.vasut+renesas@mailbox.org> |
net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux Pull Marvell 10G PHY driver from Linux 6.1.y as of commit d6d29292640d3 ("net: phy: marvell10g: select host interface configuration") and heavily adapt to match U-Boot PHY framework. Support for hwmon is removed as is much other functionality which could not be tested, this results in much simpler driver which can only bring the PHY up and set MAC type. Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
e6c5205d |
|
22-Feb-2023 |
Simon Glass <sjg@chromium.org> |
net: Add an SPL config for atheros Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split config. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
bd22bde9 |
|
10-Jan-2023 |
Tom Rini <trini@konsulko.com> |
net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move the comment from code to the help to explain what this does. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f6301702 |
|
27-Nov-2022 |
Tom Rini <trini@konsulko.com> |
net: Remove extraneous dependencies With DM_ETH being required now for all drivers, we don't need this listed on individual drivers as well. Signed-off-by: Tom Rini <trini@konsulko.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
bd22bde9 |
|
10-Jan-2023 |
Tom Rini <trini@konsulko.com> |
net: phy: mv88e61xx: Finish migration of MV88E61XX_FIXED_PORTS Set the default for MV88E61XX_FIXED_PORTS to 0x0 in Kconfig, and move the comment from code to the help to explain what this does. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f6301702 |
|
27-Nov-2022 |
Tom Rini <trini@konsulko.com> |
net: Remove extraneous dependencies With DM_ETH being required now for all drivers, we don't need this listed on individual drivers as well. Signed-off-by: Tom Rini <trini@konsulko.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
f6301702 |
|
27-Nov-2022 |
Tom Rini <trini@konsulko.com> |
net: Remove extraneous dependencies With DM_ETH being required now for all drivers, we don't need this listed on individual drivers as well. Signed-off-by: Tom Rini <trini@konsulko.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
5e6c069b |
|
17-Nov-2022 |
Tim Harvey <tharvey@gateworks.com> |
phy: add driver for Intel XWAY PHY Add a driver for the Intel XWAY GbE PHY: - configure RGMII using dt phy-mode and standard delay properties - use genphy_config Signed-off-by: Tim Harvey <tharvey@gateworks.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <neil.armstrong@linaro.org> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
612f7a61 |
|
23-Jul-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_FSL_MEMAC et al to Kconfig This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@amd.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@amd.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@amd.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
7f418ea5 |
|
15-Apr-2022 |
Tom Rini <trini@konsulko.com> |
Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net - DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]
|
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
d79f1a85 |
|
08-Apr-2022 |
Nate Drude <nate.d@variscite.com> |
phy: adin: add driver for Analog Devices ADIN1300 PHY The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@xilinx.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a2f5c936 |
|
12-Apr-2022 |
Michael Trimarchi <michael@amarulasolutions.com> |
net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@xilinx.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
448dfb40 |
|
21-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_BITBANGMII_MULTI to Kconfig This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini <trini@konsulko.com> |
#
16199a8b |
|
18-Mar-2022 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_PHY_RESET_DELAY to Kconfig This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> |
#
a744a284 |
|
23-Feb-2022 |
Michal Simek <michal.simek@xilinx.com> |
net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
f3e22eea |
|
22-Dec-2021 |
Dominic Rath <rath@ibv-augsburg.net> |
net: phy: add TI DP83869HM ethernet driver This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath <rath@ibv-augsburg.net> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
f11513d9 |
|
12-Oct-2021 |
Samuel Holland <samuel@sholland.org> |
net: phy: realtek: Add tx/rx delay config for 8211e Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b4c2c151 |
|
27-Aug-2021 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: Remove all default n/no options default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e99b1dfc |
|
09-Aug-2021 |
Kuldeep Singh <kuldeep.singh@nxp.com> |
configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
3ef2050a |
|
18-Jun-2021 |
Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> |
phy: add nxp tja1103 phy driver Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
188ff18f |
|
14-Mar-2021 |
Bin Meng <bmeng.cn@gmail.com> |
net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii() At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a70d7b01 |
|
14-Jan-2021 |
Abbie Chang <abbie.chang@cortina-access.com> |
net: phy: ca_phy: Add driver for CAxxxx SoCs Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com> Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
2a29a9a1 |
|
29-Oct-2020 |
Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> |
drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
fa6539a3 |
|
09-May-2020 |
Amit Singh Tomar <amittomer25@gmail.com> |
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> |
#
8882238c |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add DP8382x phy registration to TI PHY init Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
bc0e578f |
|
04-May-2020 |
Dan Murphy <dmurphy@ti.com> |
net: phy: Add support for TI PHY init ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Dan Murphy <dmurphy@ti.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
f641a8ac |
|
17-Jun-2019 |
Samuel Mendoza-Jonas <sam@mendozajonas.com> |
phy: Add support for the NC-SI protocol This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
389488df |
|
26-Oct-2019 |
Anatolij Gustschin <agust@denx.de> |
net: phy: fix switch vendor name Fix vendor name in MV88E61xx option description. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
e78f16b7 |
|
26-Nov-2019 |
Tom Rini <trini@konsulko.com> |
Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_CORTINA_FW_IN_MMC CONFIG_SYS_CORTINA_FW_IN_NAND CONFIG_SYS_CORTINA_FW_IN_NOR CONFIG_SYS_CORTINA_FW_IN_REMOTE CONFIG_SYS_CORTINA_FW_IN_SPIFLASH Signed-off-by: Tom Rini <trini@konsulko.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
f41e588c |
|
26-Nov-2018 |
Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> |
net: phy: Add gmiitorgmii converter support This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
77b508d3 |
|
05-Mar-2019 |
James Byrne <james.byrne@origamienergy.com> |
net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns that you shouldn't select both of them due to a device ID clash between the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately boards like the SAMA5D3xEK do contain both types of PHY, but fortunately the Linux Micrel PHY driver provides a solution by using different PHY ID and mask values to distinguish these chips. This commit contains the following changes: - The PHY ID and mask values for the KSZ9021 and the KS8721 now match those used by the Linux driver. - The warnings about not enabling both drivers have been removed. - The description for PHY_MICREL_KSZ8XXX has been corrected (these are 10/100 PHYs, not GbE PHYs). - PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE since this is selected by PHY_MICREL_KSZ90X1. - All of the relevant defconfig files have been updated now that PHY_MICREL_KSZ8XXX does not default to 'Y'. Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d47cfdbd |
|
24-Jan-2019 |
Carlo Caione <ccaione@baylibre.com> |
net: phy: realtek: Introduce quirk to mark RXC not stoppable When EEE is supported by the PHY and the driver allows it, libphy in the kernel is configuring the PHY to stop receiving the xMII clock while it is signaling LPI. While this (usually) works fine in the kernel this is causing issues in U-Boot when rebooting from the linux kernel with this bit set (without having the possibility to reset the PHY) where the PHY suddenly stops working. A new quirk is introduced to unconditionally reset this bit. If the quirk is not enabled using the proper configuration symbol, the PHY state is not changed. Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com> |
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> |
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> |
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
821560fd |
|
27-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://www.denx.de/git/u-boot-imx Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> |
#
16225590 |
|
13-Apr-2017 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://www.denx.de/git/u-boot-imx Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> |
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> |
#
4506423a |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
net: phy: aquantia: add firmware loading support Aquantia phys have firmware that can be loaded automatically from storage directly attached to the phy or via MDIO commands. Add support for loading firmware from either a file or a raw location on an MMC device. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
1c650108 |
|
18-Sep-2018 |
Jeremy Gebben <jgebben@sweptlaser.com> |
configs: migrate CONFIG_PHY_AQUANTIA to Kconfig The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
16879cd2 |
|
30-Mar-2018 |
Joe Hershberger <joe.hershberger@ni.com> |
net: phy: Don't limit phy addresses by default Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
#
66526e70 |
|
14-Feb-2018 |
kevans@FreeBSD.org <kevans@FreeBSD.org> |
net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
b30c4190 |
|
02-Feb-2018 |
Stefan Mavrodiev <stefan@olimex.com> |
Move CONFIG_PHY_ADDR to Kconfig CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
|
#
c946b0e9 |
|
06-Feb-2018 |
Michal Simek <michal.simek@xilinx.com> |
Kconfig: net: phylib: Phylib should depends on NET There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
137963d7 |
|
09-Dec-2017 |
Florian Fainelli <f.fainelli@gmail.com> |
net: phy: Add Broadcom BCM53xx switch driver Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
#
8995a96d |
|
18-Oct-2017 |
Neil Armstrong <narmstrong@baylibre.com> |
net: phy: Add Amlogic Meson GXL Internal PHY support The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
#
9a31c739 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
d397f7c4 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
cb543d30 |
|
07-Jul-2017 |
Alexandru Gagniuc <alex.g@adaptrum.com> |
net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021 Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
a43241a4 |
|
12-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
#
449ea2cd |
|
26-Mar-2017 |
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
b4f4b0f5 |
|
17-Mar-2017 |
Tim Harvey <tharvey@gateworks.com> |
drivers: net: phy: add MV88E6xx options to Kconfig Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
db40c1aa |
|
23-Mar-2017 |
Hannes Schmelzer <hannes.schmelzer@br-automation.com> |
drivers/net/phy: add fixed-phy / fixed-link support This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
#
a5fd13ad |
|
09-Dec-2016 |
John Haechten <john.haechten@microsemi.com> |
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
#
af2cbfd6 |
|
06-Feb-2017 |
Alex <alex.g@adaptrum.com> |
drivers: net: Provide Kconfig menu for PHYLIB Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|