wifi: ath9k: Remove unnecessary (void*) conversions

No need cast (void *) to (struct owl_ctx *), (struct ath_hw *),
(struct cmd_buf *) or other types.

Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230919045226.524544-1-yunchuan@nfschina.com

ath9k: owl-loader: fetch pci init values through nvmem

extends the owl loader to fetch important pci initialization
values - which are stored together with the calibration data -
through the nvmem subsystem.

This allows for much faster WIFI/ath9k initializations on devices
that do not require to perform any post-processing (like XOR'ing/
reversal or unpacking)... than the current way through the
firmware_request which involves the filesystem/userspace.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/bc79ba1c6f6435000577bf1e5f4d7ebe18a8df97.1630157099.git.chunkeey@gmail.com

ath9k: use iowrite32 over __raw_writel

This patch changes the ath9k_pci_owl_loader to use the
same iowrite32 memory accessor that ath9k_pci is using
to communicate with the PCI(e) chip.

This will fix endian issues that came up during testing
with loaned AVM Fritz!Box 7360 (Lantiq MIPS SoCs + AR9287).

Fixes: 5a4f2040fd07 ("ath9k: add loader for AR92XX (and older) pci(e)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: remove unused including <linux/version.h>

Remove including <linux/version.h> that don't need it.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: add loader for AR92XX (and older) pci(e)

Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.

Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.

Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages

Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>