sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

IfAPI: Explicitly include <net/if_private.h> in netstack

Summary:
In preparation of making if_t completely opaque outside of the netstack,
explicitly include the header. <net/if_var.h> will stop including the
header in the future.

Sponsored by: Juniper Networks, Inc.
Reviewed by: glebius, melifaro
Differential Revision: https://reviews.freebsd.org/D38200

netlink: add interface notification on link status / flags change.

* Add link-state change notifications by subscribing to ifnet_link_event.
In the Linux netlink model, link state is reported in 2 places: first is
the IFLA_OPERSTATE, which stores state per RFC2863.
The second is an IFF_LOWER_UP interface flag. As many applications rely
on the latter, reserve 1 bit from if_flags, named as IFF_NETLINK_1.
This flag is mapped to IFF_LOWER_UP in the netlink headers. This is done
to avoid making applications think this flag is actually
supported / presented in non-netlink outputs.
* Add flag change notifications, by hooking into rt_ifmsg().
In the netlink model, notification should include the bitmask for the
change flags. Update rt_ifmsg() to include such bitmask.

Differential Revision: https://reviews.freebsd.org/D37597

if_clone: migrate some consumers to the new KPI.

Convert most of the cloner customers who require custom params
to the new if_clone KPI.

Reviewed by: kp
Differential Revision: https://reviews.freebsd.org/D36636
MFC after: 2 weeks

net80211: consistently use the IEEE80211_M_ memory related options

Replace a malloc() by IEEE80211_MALLOC().
For malloc flags even in the local ieee80211_freebsd.c there was a mix
of both versions M_ and IEEE80211_M_.
Consistently use the IEEE80211_M_ malloc options everywhere.
If the field is changed for malloc, it'll also be changed for the
other accessor functions taking a "how" field to avoid any confusion.

Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D36249

net80211: prefix get_random_bytes() with net80211_

Both linux/random.h and net80211 have a function named
get_random_bytes(). With overlapping files included these collide.
Arguably the function could be renamed in linuxkpi but the generic
name should also not be used in net80211 so rename it there.

Sponsored-by: The FreeBSD Foundation
MFC-after: 2 weeks
Reviewed-by: philip, adrian
Differential Revision: https://reviews.freebsd.org/D29335

net80211: factor out the priv(9) checks into OS specifc code.

Factor out the priv(9) checks into OS specifc code so other OSes can equally
implement them. This sorts out those XXX in the net80211 code.
We provide 3 arguments (cmd, vap, ifp) where available to the functions, in
order to allow other OSes to use that data but also in case we'd add auditing
to these check to have the information available. For now the arguments are
marked __unused.

PR: 249403
Reported by: martin(NetBSD)
Reviewed by: adrian, martin(NetBSD)
MFC after: 10 days
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26541

Provide MS() and SM() macros for 80211 and wireless drivers.

We have (two versions) of MS() and SM() macros which we use throughout
the wireless code. Change all but three places (ath_hal, rtwn, and rsu)
to the newly provided _IEEE80211_MASKSHIFT() and _IEEE80211_SHIFTMASK()
macros. Also change one internal case using both _S and _M instead of
just _S away from _M (one of the reasons rtwn and rsu were not changed).

This was done semi-mechanically. No functional changes intended.

Requested by: gnn (D26091)
Reviewed by: adrian (pre line wrap)
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26539

net: clean up empty lines in .c and .h files

[net80211] Add new privileges; restrict what can be done in a jail.

Split the MANAGE privilege into MANAGE, SETMAC and CREATE_VAP.

+ VAP_MANAGE is everything but setting the MAC and creating a VAP.
+ VAP_SETMAC is setting the MAC address of the VAP.
Typically you wouldn't want the jail to be able to modify this.
+ CREATE_VAP is to create a new VAP. Again, you don't want to be doing
this in a jail, but this DOES stop being able to run some corner
cases like Dynamic WDS (DWDS) AP in a jail/vnet. We can figure this
bit out later.

This allows me to run wpa_supplicant in a jail after transferring
a STA VAP into it. I unfortunately can't currently set the wlan
debugging inside the jail; that would be super useful!

Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D25630

Fix !DEBUGNET build after r362138

X-MFC-With: r362138

net80211: Add framework for debugnet(4) support

Allow net80211 drivers to register a small vtable of debugnet-related
methods.

This is not a functional change. Driver support is needed, similar to
debugnet(4) for wired NICs.

Reviewed by: adrian, markj (earlier version both)
Differential Revision: https://reviews.freebsd.org/D17308

[net80211] ok ok if_xname won't ever be NULL.

Somewhere in net80211 if_xname is checked against NULL but it doesn't trigger
a compiler warning, but this does. So DTRT for FreeBSD and the other if_xname
derefences can be converted to this function at a later time.

[net80211] Add a method to return the vap's ifname.

This removes the requirement to know what's in the ifp.

(If someone wants a quick clean-up task, it'd be nice to convert instances
of ifp dereferencing for if_xname over to this method.)

[net80211] Print out a bad PN in both hex and decimal.

I've been using this to visually identify when I'm getting corrupted PNs
from the hardware. :(

net80211: post RTM_IFINFO notification after toggling IFF_DRV_RUNNING

This is useful when a wireless driver is stopped or started in response
to events like an RF Kill button press. Applications like
wpa_supplicant depend on such events to have a correct view of interface
state.

Reviewed by: adrian, cy, melifaro
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D24925

Mark more nodes as CTLFLAG_MPSAFE or CTLFLAG_NEEDGIANT (7 of many)

r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.

This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.

Mark all low hanging fruits as MPSAFE.

Reviewed by: markj
Approved by: kib (mentor, blanket)
Differential Revision: https://reviews.freebsd.org/D23626

Drop unused M_80211_COM malloc(9) type.

It is not used since r287197.

MFC after: 3 days

net80211: reuse TICKS_2_MSEC / MSEC_2_TICKS macros from sys/time.h

Replace in-place implementation with system-wide one; since it
guarantees non-zero result drop all less-than-one checks from
drivers and net80211.

MFC after: 2 weeks

net80211: resolve ioctl <-> detach race for ieee80211com structure

Since r287197 ieee80211com is a part of drivers softc; as a result,
after detach all pointers to it (iv_ic, ni_ic) are invalid. Most
possible users (tasks, interrupt handlers) are blocked / removed
when device is stopped; however, ioctl handlers were not tracked
and may crash if ieee80211com structure is accessed.

Since ieee80211com pointer access from ieee80211vap structure is not
protected by lock (constant after interface creation) and used in
many other places just use reference counting for ioctl handlers;
on detach set 'detached' flag and wait until reference counter goes to 0.

For HEAD ieee80211vap size was changed (__FreeBSD_version bumped);
however, in stable branches I'm going to split / reuse the last
iv_spare field for KBI stability.

Tested with:
- rsu(4), SIOCSIFCAP (-rxcsum) ioctl;
- rtwn_pci(4), SIOCG80211 / IEEE80211_IOC_HTPROTMODE ioctl.

MFC after: 1 week

sys: general adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

No functional change intended.

[net80211] add a sysctl that forces a vap restart.

Well, vap restart really does "all restart" for now, which will be a good
way of debugging firmware restart issues.

[net80211] Add a variant on ieee80211_get_rx_params() that returns a pointer.

Be careful when calling this, as the underlying mbuf may change
afterwards - common in the RX path.

[net80211] add in ToA/ToD based location mbuf tags for some experimenting.

net80211: fix more compiler warnings.

ieee80211.c:
add_chanlist(): 'error' variable will be uninitialized if
no channels were passed; return '0' instead.
ieee80211_action.c:
ieee80211_send_action_register(): drop 'break' after 'return'.
ieee80211_crypto_none.c:
none_encap(): 'keyid' is not used in non-debug builds; hide it
behind IEEE80211_DEBUG ifdef.
ieee80211_freebsd.c:
Staticize global 'ieee80211_debug' variable (used only in this
file).
ieee80211_hostap.c:
Fix a comment (associatio -> association).
ieee80211_ht.c:
ieee80211_setup_htrates(): initialize 'maxunequalmcs' to 0 to mute
compiler warning.
ieee80211_hwmp.c:
hwmp_recv_preq(): copy 'prep' between conditional blocks to fix
-Wshadow warning.
ieee80211_mesh.c:
mesh_newstate(): remove duplicate 'ni' definition.
mesh_recv_group_data(): fix -Wempty-body warning in non-debug
builds.
ieee80211_phy.c:
ieee80211_compute_duration(): remove 'break' after panic() call.
ieee80211_scan_sta.c:
Hide some TDMA-specific macros under IEEE80211_SUPPORT_TDMA ifdef
adhoc_pick_bss(): remove 'ic' pointer redefinition.
ieee80211_sta.c:
sta_beacon_miss(): remove 'ic' pointer redefinition.
ieee80211_superg.c:
superg_ioctl_set80211(): drop unreachable return.

Tested with clang 3.8.0, gcc 4.6.4 and gcc 5.3.0.

net80211: restore 'iflladdr_event' event handler.

Now 'ether' argument to ifconfig can be used as an alias to 'wlanaddr'.

PR: 208933

sys: use our roundup2/rounddown2() macros when param.h is available.

rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.

This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.

These files were getting sys/malloc.h and vm/uma.h with header pollution
via sys/mbuf.h

Remove sys/eventhandler.h from net/route.h

Reviewed by: ae

net80211: free node reference in the ieee80211_parent_xmitpkt() when error happened.

Move error handling into ieee80211_parent_xmitpkt() instead of spreading it
between functions.

Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3772

net80211: separate mbuf cleanup from ieee80211_fragment()

* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.

This should be a big no-op.

Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769

Perform some rather amusing layering violations to add mbuf tags to the
net80211 receive path. This allows drivers (notably USB right now, but
anything/everything!) to optionally defer bulk RX of 802.11 frames until
/outside/ of the driver lock(s), rather than doing:

UNLOCK(sc);
ieee80211_input*()
LOCK(sc);

.. which is really stupid.

The existing API is maintaned - if ieee80211_input() / ieee80211_input_all()
is called then the RSSI/NF values are used. If the MIMO versions are called
with a given rx status pointer then it's used. Else, it'll use whatever
is in the RX mbuf tag.

Replay r286410. Change KPI of how device drivers that provide wireless
connectivity interact with the net80211 stack.

Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.

Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:

- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.

Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.

Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.

Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.

Revert the wifi ifnet changes until things are more baked and tested.

* 286410
* 286413
* 286416

The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.

Change KPI of how device drivers that provide wireless connectivity interact
with the net80211 stack.

Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.

Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:

- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.

Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.

Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:

https://wiki.freebsd.org/projects/ifnet/net80211

Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.

Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix

First pass of adding transmit parameters as an option for outbound
802.11 mbufs.

The raw transmit path currently doesn't make it easy to queue
these frames:

* there's no node reference stored in the mbuf, like for the normal
path, and
* the bpf supplied raw transmit parameters (rate, rts/cts, etc)
are passed in as an argument, not as an mbuf tag.

In order to support driver queuing of these frames, we need to
be able to put the above into the mbuf before the driver gets it,
so the driver /can/ put it into a queue if needed.

Use an mbuf tag and for now just verbatim copy the bpf parameters
into it. Later on it may grow to include more options but this
will do for now.

Why would you want to queue raw frames? Well, in the case of
iwn(4), we can't send the firmware frames to transmit before
we hear a beacon - the firmware will consider passive channels
as unavailable until it hears a beacon. The firmware "passive"
channel state is cleared upon each RXON command, which is sent to
update association status. So, when we attempt association and
authorisation, the RXON command causes the firmware to clear out
what it's already seen, and so we have to wait for a beacon before
we can transmit.

Before people get overly excited - this alone doesn't "fix" 5GHz
operation - it just makes it (more) possible.

The aim here is to convert all the drivers over to use a raw_xmit()
API that doesn't include the node and params - instead they'd get
those from the mbuf. Then raw_xmit() becomes just a side-channel
version of the normal transmit path for management traffic.

MFC after: 2 weeks
Sponsored by: Norse Corp, Inc.

Cleanup compat shims for FreeBSD versions that predate 10.0-RELEASE.
There are no plans to merge anything save a trivial bugfix to stable/9.

Discussed with: adrian

When sending RTM_IEEE80211_CSA, RTM_IEEE80211_RADAR, RTM_IEEE80211_CAC and
RTM_IEEE80211_RADIO routing messages, broadcast them on all vap interfaces
instead of sending them on parent.

Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.

Convert malloc/free back to #define's, as part of OS portability work.

DragonflyBSD uses the FreeBSD wireless stack and drivers. Their malloc()
API is named differently, so they don't have userland/kernel symbol
clashes like we do (think libuinet.)

So, to make it easier for them and to port to other BSDs/other operating
systems, start hiding the malloc specific bits behind defines in
ieee80211_freebsd.h.

DragonflyBSD can now put these portability defines in their local
ieee80211_dragonflybsd.h.

This should be a great big no-op for everyone running wifi.

TODO:

* kill M_WAITOK - some platforms just don't want you to use it
* .. and/or handle it returning NULL rather than waiting forever.
* MALLOC_DEFINE() ?
* Migrate the well-known malloc names (eg M_TEMP) to net80211
namespace defines.

Use name from ieee80211com instead of parent ifnet, in debugging printfs.

Sponsored by: Netflix
Sponsored by: Nginx, Inc.

EVENTHANDLER_REGISTER() doesn't fail.

Use SYSCTL_OUT_STR() to return strings.

PR: 195668

To ease changes to underlying mbuf structure and the mbuf allocator, reduce
the knowledge of mbuf layout, and in particular constants such as M_EXT,
MLEN, MHLEN, and so on, in mbuf consumers by unifying various alignment
utility functions (M_ALIGN(), MH_ALIGN(), MEXT_ALIGN() in a single
M_ALIGN() macro, implemented by a now-inlined m_align() function:

- Move m_align() from uipc_mbuf.c to mbuf.h; mark as __inline.
- Reimplement M_ALIGN(), MH_ALIGN(), and MEXT_ALIGN() using m_align().
- Update consumers around the tree to simply use M_ALIGN().

This change eliminates a number of cases where mbuf consumers must be aware
of whether or not mbufs returned by the allocator use external storage, but
also assumptions about the size of the returned mbuf. This will make it
easier to introduce changes in how we use external storage, as well as
features such as variable-size mbufs.

Differential Revision: https://reviews.freebsd.org/D1436
Reviewed by: glebius, trasz, gnn, bz
Sponsored by: EMC / Isilon Storage Division

The r48589 promised to remove implicit inclusion of if_var.h soon. Prepare
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h

Sponsored by: Netflix
Sponsored by: Nginx, Inc.

Fix the "am I a net80211 vap" check for bpf listeners.

I changed it to use if_transmit a while ago but apparently with monitor
mode the if_transmit method is overridden.

This is (mostly) a workaround until a more permanent solution can be
found.

Submitted by: Patrick Kelsey <kelsey@ieee.org>
Approved by: re@ (gjb)

Convert net80211 over to using if_transmit for the dispatch from the
upper layer(s).

This eliminates the if_snd queue from net80211. Yay!

This unfortunately has a few side effects:

* It breaks ALTQ to net80211 for now - sorry everyone, but fixing
parallelism and eliminating the if_snd queue is more important
than supporting this broken traffic scheduling model. :-)

* There's no VAP and IC flush methods just yet - I think I'll add
some NULL methods for now just as placeholders.

* It reduces throughput a little because now net80211 will drop packets
rather than buffer them if the driver doesn't do its own buffering.
This will be addressed in the future as I implement per-node software
queues.

Tested:

* ath(4) and iwn(4) in STA operation

Add VNET wrappers around the rest of the ieee80211 rtsock messages.

I triggered the cac/radar messages when doing testing in DFS channels.

Bring over my initial work from the net80211 TX locking branch.

This patchset implements a new TX lock, covering both the per-VAP (and
thus per-node) TX locking and the serialisation through to the underlying
physical device.

This implements the hard requirement that frames to the underlying physical
device are scheduled to the underlying device in the same order that they
are processed at the VAP layer. This includes adding extra encapsulation
state (such as sequence numbers and CCMP IV numbers.) Any order mismatch
here will result in dropped packets at the receiver.

There are multiple transmit contexts from the upper protocol layers as well
as the "raw" interface via the management and BPF transmit paths.
All of these need to be correctly serialised or bad behaviour will result
under load.

The specifics:

* add a new TX IC lock - it will eventually just be used for serialisation
to the underlying physical device but for now it's used for both the
VAP encapsulation/serialisation and the physical device dispatch.

This lock is specifically non-recursive.

* Methodize the parent transmit, vap transmit and ic_raw_xmit function
pointers; use lock assertions in the parent/vap transmit routines.

* Add a lock assertion in ieee80211_encap() - the TX lock must be held
here to guarantee sensible behaviour.

* Refactor out the packet sending code from ieee80211_start() - now
ieee80211_start() is just a loop over the ifnet queue and it dispatches
each VAP packet send through ieee80211_start_pkt().

Yes, I will likely rename ieee80211_start_pkt() to something that
better reflects its status as a VAP packet transmit path. More on
that later.

* Add locking around the management and BAR TX sending - to ensure that
encapsulation and TX are done hand-in-hand.

* Add locking in the mesh code - again, to ensure that encapsulation
and mesh transmit are done hand-in-hand.

* Add locking around the power save queue and ageq handling, when
dispatching to the parent interface.

* Add locking around the WDS handoff.

* Add a note in the mesh dispatch code that the TX path needs to be
re-thought-out - right now it's doing a direct parent device transmit
rather than going via the vap layer. It may "work", but it's likely
incorrect (as it bypasses any possible per-node power save and
aggregation handling.)

Why not a per-VAP or per-node lock?

Because in order to ensure per-VAP ordering, we'd have to hold the
VAP lock across parent->if_transmit(). There are a few problems
with this:

* There's some state being setup during each driver transmit - specifically,
the encryption encap / CCMP IV setup. That should eventually be dragged
back into the encapsulation phase but for now it lives in the driver TX path.
This should be locked.

* Two drivers (ath, iwn) re-use the node->ni_txseqs array in order to
allocate sequence numbers when doing transmit aggregation. This should
also be locked.

* Drivers may have multiple frames queued already - so when one calls
if_transmit(), it may end up dispatching multiple frames for different
VAPs/nodes, each needing a different lock when handling that particular
end destination.

So to be "correct" locking-wise, we'd end up needing to grab a VAP or
node lock inside the driver TX path when setting up crypto / AMPDU sequence
numbers, and we may already _have_ a TX lock held - mostly for the same
destination vap/node, but sometimes it'll be for others. That could lead
to LORs and thus deadlocks.

So for now, I'm sticking with an IC TX lock. It has the advantage of
papering over the above and it also has the added advantage that I can
assert that it's being held when doing a parent device transmit.
I'll look at splitting the locks out a bit more later on.

General outstanding net80211 TX path issues / TODO:

* Look into separating out the VAP serialisation and the IC handoff.
It's going to be tricky as parent->if_transmit() doesn't give me the
opportunity to split queuing from driver dispatch. See above.

* Work with monthadar to fix up the mesh transmit path so it doesn't go via
the parent interface when retransmitting frames.

* Push the encryption handling back into the driver, if it's at all
architectually sane to do so. I know it's possible - it's what mac80211
in Linux does.

* Make ieee80211_raw_xmit() queue a frame into VAP or parent queue rather
than doing a short-cut direct into the driver. There are QoS issues
here - you do want your management frames to be encapsulated and pushed
onto the stack sooner than the (large, bursty) amount of data frames
that are queued. But there has to be a saner way to do this.

* Fragments are still broken - drivers need to be upgraded to an if_transmit()
implementation and then fragmentation handling needs to be properly fixed.

Tested:

* STA - AR5416, AR9280, Intel 5300 abgn wifi
* Hostap - AR5416, AR9160, AR9280
* Mesh - some testing by monthadar@, more to come.

Substitute '#ifdef ALIGNED_POINTER' with '#ifndef __NO_STRICT_ALIGNMENT',
since the former is defined everywhere. This cuts off some code not
necessary on non strict aligment arches.

Reviewed by: adrian
Sponsored by: Nginx, Inc.

Mechanically substitute flags from historic mbuf allocator with
malloc(9) flags within sys.

Exceptions:

- sys/contrib not touched
- sys/mbuf.h edited manually

Oops, missed in my last commit.

Allow net80211 to be built on -9 and -8.

There are some people who use the -HEAD net80211 and wireless drivers
on earlier FreeBSD versions in order to get the updated 802.11n support.
The previous if_clone API changes broke this.

Fix up some initial issues with creation and deletion of hotplugged
net80211 devices and vaps.

* vnet sets vnet0 during kldload and device probe/attach, but not for
the hotplug event. Thus, plugging in a NIC causes things to panic.
So, add a CURVNET_SET(vnet0) for now during the attach phase, until
the hotplug code is taught to set CURVNET_SET(vnet0).

* there's also no implied detach vnet context - so teach the detach
path about ifp->if_vnet.

* When creating/deleting vaps, also set the vnet context appropriately.
These can be done at any time.

Now, the problems!

* ieee80211.c is supposed to be OS-portable code, with no OS-specific stuff
like vnet. That should be fixed.

* When the device hotplug code gets taught about CURVNET_SET(vnet0), the
device vnet set can go away; but the VAP vnet set still needs to be there.

* .. and there still is the question about potentially adding an implied
CURVNET_SET(ifp->if_vnet) on if_free(), since any/all devices may end up
being detached by a hotplug event in today's world. That's going to be
a topic of a subsequent commit.

Make the "struct if_clone" opaque to users of the cloning API. Users
now use function calls:

if_clone_simple()
if_clone_advanced()

to initialize a cloner, instead of macros that initialize if_clone
structure.

Discussed with: brooks, bz, 1 year ago

Revert previous commit...

Pointyhat to: kevlo (myself)

Prefer NULL over 0 for pointers

Correct the ordering of tid/crypto ic_name.

Because the code lacks all the GNU extensions to printf() format stuff,
the compiler doesn't helpfully tell us that I messed up in a previous
commit.

Pointy hat to: adrian, who likely only cares about this because he's the
only one who bothers flipping on net80211 debugging.

Pull in a dependency on ALQ if it's compiled with IEEE80211_ALQ.

Mark MALLOC_DEFINEs static that have no corresponding MALLOC_DECLAREs.

This means that their use is restricted to a single C file.

Include the tid when printing out crypto replay errors.

I found this useful when trying to debug the AR9160 STA RX filter issue -
I'd get crypto reply errors but it wasn't entirely clear which TID it
was for.

Specify a CTLTYPE_FOO so that a future sysctl(8) change does not need
to rely on the format string. For SYSCTL_PROC instances that I
noticed a discrepancy between the CTLTYPE and the format specifier,
fix the CTLTYPE.

sysctl(9) cleanup checkpoint: amd64 GENERIC builds cleanly.

Commit the net* piece.

A new jail(8) with a configuration file, to replace the work currently done
by /etc/rc.d/jail.

MFC r202612

Use the iflladdr_event event to keep the mac address on the vap in sync with
the parent wirless interface. If the user passed in a mac address or it was
autogenerated then flag this to avoid trashing it on update.

This will fix wlan+lagg in a post vap world.

Use the iflladdr_event event to keep the mac address on the vap in sync with
the parent wirless interface. If the user passed in a mac address or it was
autogenerated then flag this to avoid trashing it on update.

This will fix wlan+lagg in a post vap world.

Merge the remainder of kern_vimage.c and vimage.h into vnet.c and
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.

Reviewed by: bz
Approved by: re (vimage blanket)

Move code that does payload realigment to a new routine, ieee80211_realign,
so it can be reused. While here rewrite the logic to always use a single mbuf.

Reviewed by: rpaulo
Approved by: re (kib)

add tid param to ieee80211_notify_replay_failure to get the correct rsc

Remove hack used to deal with ifnet teardown now that if_detach and the
bridge do a better job.
o move ether_ifdetach to the top of ieee80211_detach
o do not clear if_softc at the top of ieee80211_detach; we no longer need
this because we are safeguarded against calls coming back through if_ioctl
o simplify the bpf tracker now that we don't null if_softc

This also fixes an issue where having a bpf consumer active when a vap
is destroyed would cause a crash because bpf referenced free'd memory.

Reviewed by: imp

Fix monitor mode vaps to work as intended:
o track # bpf taps on monitor mode vaps instead of # monitor mode vaps
o spam monitor mode taps on tx/rx
o fix ieee80211_radiotap_rx_all to dispatch frames only if the vap is up
o while here print radiotap (and superg) state in show com

distribute sysctl decls so global variables can be made static

do internal bpf tracking only for radiotap DLT's

Prepare to distribute sysctl code to reduce global definitions:
o expose net.wlan sysctl node
o expose ieee80211_sysctl_msecs_ticks

Reviewed by: rpaulo, thompsa

Overhaul monitor mode handling:
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi

Reviewed by: cbzimmer, rpaulo, thompsa

add missing type for SYSCTL_PROC items; w/o a type you can view the value
but not change it

Change the curvnet variable from a global const struct vnet *,
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.

This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.

The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.

The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.

This change also introduces a DDB subcommand to show the list of all
vnet instances.

Approved by: julian (mentor)

Hoist 802.11 encapsulation up into net80211:
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS

With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.

Reviewed by: thompsa, rpaulo, avatar, imp, sephe

Eliminate ic_myaddr so changing the mac address of a device works correctly:
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)

PR: kern/133178
Reviewed by: thompsa, rpaulo

TDMA support for long distance point-to-point links using ath devices:
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits

While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.

Sponsored by: Intel

convert MALLOC/FREE to malloc/free

Revert the removal of the MALLOC and FREE macros from the net80211 code.

Requested by: sam

Retire the MALLOC and FREE macros. They are an abomination unto style(9).

MFC after: 3 months

- Import the HEAD csup code which is the basis for the cvsmode work.

Fix clone destruction, can't use the simple api because that does not remove
the ifnet from cloner's list. Expose if_clone_destroyif api to do this.

Submitted by: sam

add a sysctl to deliver a radar event for testing

Minor cleanup of vap create work:
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release

Multi-bss (aka vap) support for 802.11 devices.

Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.

Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)

sync 11n support with vap code base; many changes based on interop
testing with all major vendors

MFC after: 1 week

Fix following nits:
- Per ieee80211com sysctl ctx leakage on detach
- getmgtframe incorrectly adjusts mbuf.m_data

Reviewed by: sam
Approved by: re (bmah), sam (mentor)

Update 802.11 wireless support:
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing

Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested

This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.

copyright updates:
o update to include 2007
o switch back to a 2-clause bsd-only license

Reviewed by: onoe

Fix potential node refcnt leak. If mbufs are q'd on ic_mgtq when
the state machine clocks to INIT, node references are not reclaimed.
Add a new routine ieee80211_drain_ifq that does this and use it
instead of IF_DRAIN.

Submitted by: Sepherosa Ziehau
Obtained from: DragonFly
MFC after: 1 month

remove duplicate ifname in debug msg

MFC after: 1 week

Use kern_kldload() and kern_kldunload() to load and unload modules when
we intend for the user to be able to unload them later via kldunload(2)
instead of calling linker_load_module() and then directly adjusting the
ref count on the linker file structure. This makes the resulting
consumer code simpler and cleaner and better hides the linker internals
making it possible to sanely lock the linker.

Add ieee80211_beacon_miss for processing sta mode beacon miss events
in the 802.11 layer: we send a directed probe request frame to the
current ap bmiss_max times (w/o answer) before scanning for a new ap.

MFC after: 2 weeks

Retire MT_HEADER mbuf type and change its users to use MT_DATA.

Having an additional MT_HEADER mbuf type is superfluous and redundant
as nothing depends on it. It only adds a layer of confusion. The
distinction between header mbuf's and data mbuf's is solely done
through the m->m_flags M_PKTHDR flag.

Non-native code is not changed in this commit. For compatibility
MT_HEADER is mapped to MT_DATA.

Sponsored by: TCP/IP Optimization Fundraise 2005

Split crypto tx+rx key indices and add a key index -> node mapping table:

Crypto changes:
o change driver/net80211 key_alloc api to return tx+rx key indices; a
driver can leave the rx key index set to IEEE80211_KEYIX_NONE or set
it to be the same as the tx key index (the former disables use of
the key index in building the keyix->node mapping table and is the
default setup for naive drivers by null_key_alloc)
o add cs_max_keyid to crypto state to specify the max h/w key index a
driver will return; this is used to allocate the key index mapping
table and to bounds check table loookups
o while here introduce ieee80211_keyix (finally) for the type of a h/w
key index
o change crypto notifiers for rx failures to pass the rx key index up
as appropriate (michael failure, replay, etc.)

Node table changes:
o optionally allocate a h/w key index to node mapping table for the
station table using the max key index setting supplied by drivers
(note the scan table does not get a map)
o defer node table allocation to lateattach so the driver has a chance
to set the max key id to size the key index map
o while here also defer the aid bitmap allocation
o add new ieee80211_find_rxnode_withkey api to find a sta/node entry
on frame receive with an optional h/w key index to use in checking
mapping table; also updates the map if it does a hash lookup and the
found node has a rx key index set in the unicast key; note this work
is separated from the old ieee80211_find_rxnode call so drivers do
not need to be aware of the new mechanism
o move some node table manipulation under the node table lock to close
a race on node delete
o add ieee80211_node_delucastkey to do the dirty work of deleting
unicast key state for a node (deletes any key and handles key map
references)

Ath driver:
o nuke private sc_keyixmap mechansim in favor of net80211 support
o update key alloc api

These changes close several race conditions for the ath driver operating
in ap mode. Other drivers should see no change. Station mode operation
for ath no longer uses the key index map but performance tests show no
noticeable change and this will be fixed when the scan table is eliminated
with the new scanning support.

Tested by: Michal Mertl, avatar, others
Reviewed by: avatar, others
MFC after: 2 weeks

pass re-association events up using a new message type

be consistent in naming inactivity timers;
net.wlan.X.inact -> net.wlan.X.inact_run

bump copyright for 2005

o add net.wlan.X.driver_caps mib variable for setting the driver capabilities
flags for testing
o debug msg consistency fixups

cover up the landmine until there's a proper solution

fixup printf arguments for 64-bit machines

Update 802.11 support; too much new functionality to fully describe
here but it includes completed 802.11g, WPA, 802.11i, 802.1x, WME/WMM,
AP-side power-save, crypto plugin framework, authenticator plugin framework,
and access control plugin frameowrk.