sys: Remove $FreeBSD$: one-line sh pattern

Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/

Move gpiobus routines to dev/gpio. Avoid polluting ofw_bus with bus
specific parts.

Requested by: nwhitehorn

Fix the gpio-specifier decoding by respecting the GPIO controller's
#gpio-cells property.

Add a new ofw_bus method (OFW_BUS_MAP_GPIOS()) that allows the GPIO
controller to implement its own mapping to deal with gpio-specifiers,
allowing the decoding of gpio-specifiers to be controller specific.

The default ofw_bus_map_gpios() decodes the linux standard (#gpio-cells =
<2>) and the FreeBSD standard (#gpio-cells = <3>).

It pass the gpio-specifier flag field to the children as an ivar variable so
they can act upon.

Add a set of helpers (ofw_bus_get_status() and ofw_bus_status_okay()) to
process "status" properties of OF nodes.

I've avoided adding new KOBJ methods here so that we don't have to modify
every ofw_bus in the tree. Since 100% of implementations of ofw_bus use
only ofw_bus_gen_*(), it might be worth garbage-collecting the other
methods as well.

Open Firmware interrupt specifiers can consist of arbitrary-length byte
strings and include arbitrary information (IRQ line/domain/sense). When the
ofw_bus_map_intr() API was introduced, it assumed that, as on most systems,
these were either 1 cell, containing an interrupt line, or 2, containing
a line number plus a sense code. It turns out a non-negligible number of
ARM systems use 3 (or even 4!) cells for interrupts, so make this more
general.

Fix a typo on a comment in ofw_bus_if.m, the default method will return -1
when a node doesn't exist.

Reviewed by: nwhitehorn
Approved by: adrian (mentor)

Add two new interfaces to ofw_bus:
- ofw_bus_map_intr()
Maps an (iparent, IRQ) tuple to a system-global interrupt number in some
platform dependent way. This is meant to be implemented as a replacement
for [FDT_]MAP_IRQ() that is an MI interface that knows about the bus
hierarchy.
- ofw_bus_config_intr()
Configures an interrupt (previously mapped) based on firmware sense flags.
This replaces manual interpretation of the sense field in bus drivers and
will, in a follow-up, allow that interpretation to be redirected to the PIC
drivers where it belongs. This will eventually replace the tables in
/sys/dev/fdt/fdt_ARCH.c

The PowerPC/AIM code has been converted to use these globally, with an
implementation in terms of MAP_IRQ() and powerpc_config_intr(), assuming
OpenPIC, at the bus root in nexus(4). The ofw_bus_config_intr() will shortly
be integrated into pic_if.m and bounced through nexus into the PIC tree.

FDT integration will happen significantly later due to larger testing
requirements. This patch in general also lays the groundwork for the removal
of /sys/dev/fdt/fdt_ARCH.c and machine/fdt.h.

Make ofw_bus_get_node() consistently return -1 when there is no associated
OF node, instead of a random mixture of 0 and -1. Update all checks for 0
to check for -1 instead.

MFC after: 4 weeks

A new jail(8) with a configuration file, to replace the work currently done
by /etc/rc.d/jail.

- Import the HEAD csup code which is the basis for the cvsmode work.

- Add a new method ofw_bus_default_get_devinfo() that allows to retrieve
a newly introduced struct ofw_bus_devinfo which can hold the OFW info
of a device recallable via the ofw_bus KOBJ interface. Introduce a set
of functions ofw_bus_gen_get_*() which use ofw_bus_default_get_devinfo()
to provide generic subroutines for implementing the rest of the ofw_bus
KOBJ interface in a bus driver.
This is inspired by bus_get_resource_list() and bus_generic_rl_*_resource()
and allows to reduce code duplication in bus drivers as they only have
to provide an ofw_bus_default_get_devinfo() implementation in order to
provide the ofw_bus KOBJ interface via ofw_bus_gen_get_*().
- While here add a comment to ofw_bus_if.m describing the intention of
the ofw_bus KOBJ interface.

Reviewed by: marcel

Start each of the license/copyright comments with /*-, minor shuffle of lines

- Introduce an ofw_bus kobj-interface for retrieving the OFW node and a
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.

Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386