ath: Fix typo (triple M)

Reviewed by: imp
Pull Request: https://github.com/freebsd/freebsd-src/pull/963

sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

ath: clean up empty lines in .c and .h files

[ath] [ath_hal] Propagate the HAL_RESET_TYPE through to the chip reset; set it during ath_reset()

Although I added the reset type field to ath_hal_reset() years ago,
I never finished adding it both throughout the HALs and in if_ath.c.

This will eventually deprecate the ath_hal force_full_reset option
because it can be requested at the driver layer.

So:

* Teach ar5416ChipReset() and ar9300_chip_reset() about the HAL type
* Use it in ar5416Reset() and ar9300_reset() when doing a full chip reset
* Extend ath_reset() to include the HAL_RESET_TYPE parameter added in the above functions
* Use HAL_RESET_NORMAL in most calls to ath_reset()
* .. but use HAL_RESET_BBPANIC for the BB panics, and HAL_RESET_FORCE_COLD during fatal, beacon miss and other hardware related hangs.

This should be a glorified no-op outside of actual hardware issues.
I've tested things with ath_hal force_full_reset set to 1 for years now,
so I know that feature and a full reset works (albeit much slower than
a warm reset!) and it does unwedge hardware.

The eventual aim is to use this for all the places where the driver
detects a potential hang as well as if long calibration - ie, noise floor
calibration - fails to complete. That's one of the big hardware related
things that causes station mode operation to hang without easy recovery.

Differential Revision: https://reviews.freebsd.org/D24981

SPDX: license IDs for some ISC-related files.

sys/dev: replace comma with semicolon when pertinent.

Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.

Detected with devel/coccinelle following a hint from DragonFlyBSD.

MFC after: 1 month

[ath_hal] retire a "long RX desc" flag, store/use the TX/RX timestamp length.

* the code already stored the length of the RX desc, which I never used.
So, use that and retire the new flag I introduced a while ago.
* Introduce a TX timestamp length field and capability.

Flip on fast frames support for AR5416 and AR9300 series NICs.

This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.

Now that net80211 doesn't panic, let's flip this back on.

It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)

Tested:

* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.

To make this possible:

* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.

This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.

Tested:

* AR9380 (STA)
* AR9485 CUS198 (STA)

Obtained from: Qualcomm Atheros, Linux ath9k

Note that the AR5416 and later hardware supports the MYBEACON RX filter.

Add bluetooth fixes to the AR5416/AR92xx HAL:

* Call the bluetooth setup function during the reset path, so the bluetooth
settings are actually initialised.
* Call the AR9285 diversity functions during bluetooth setup; so the AR9285
diversity and antenna configuration registers are correctly programmed
* Misc debugging info.

Tested:

* AR9285+AR3011 bluetooth combo; this code itself doesn't enable bluetooth
coexistence but it's part of what I'm currently using.

add a method to set/clear the VMF field in the TX descriptor.

Obtained from: Qualcomm Atheros

Begin adding support to explicitly set the current chainmask.

Right now the only way to set the chainmask is to set the hardware
configured chainmask through capabilities. This is fine for forcing
the chainmask to be something other than what the hardware is capable
of (eg to reduce TX/RX to one connected antenna) but it does change what
the HAL hardware chainmask configuration is.

For operational mode changes, it (may?) make sense to separately control
the TX/RX chainmask.

Right now it's done as part of ar5416_reset.c - ar5416UpdateChainMasks()
calculates which TX/RX chainmasks to enable based on the operating mode.
(1 for legacy and whatever is supported for 11n operation.) But doing
this in the HAL is suboptimal - the driver needs to know the currently
configured chainmask in order to correctly enable things for each
TX descriptor. This is currently done by overriding the chainmask
config in the ar5416 TX routines but this has to disappear - the AR9300
HAL support requires the driver to dynamically set the TX chainmask based
on the TX power and TX rate in order to meet mini-PCIe slot power
requirements.

So:

* Introduce a new HAL method to set the operational chainmask variables;
* Introduce null methods for the previous generation chipsets;
* Add new driver state to record the current chainmask separate from
the hardware configured chainmask.

Part #2 of this will involve disabling ar5416UpdateChainMasks() and moving
it into the driver; as well as properly programming the TX chainmask
based on the currently configured HAL chainmask.

Tested:

* AR5416, STA mode - both legacy (11a/11bg) and 11n rates - verified
that AR_SELFGEN_MASK (the chainmask used for self-generated frames like
ACKs and RTSes) is correct, as well as the TX descriptor contents is
correct.

Be slightly more paranoid with the TX DMA buffer maximum threshold.

Specifically - never jack the TX FIFO threshold up to the absolute
maximum; always leave enough space for two DMA transactions to
appear.

This is a paranoia from the Linux ath9k driver. It can't hurt.

Obtained from: Linux ath9k

Remove this unneeded printf(), sorry!

Configure larger TX FIFO default and maximum level values.

This has reduced the number of TX delimiter and data underruns when
doing large UDP transfers (>100mbit).

This stops any HAL_INT_TXURN interrupts from occuring, which is a good
sign!

Obtained from: Qualcomm Atheros

Bring over the basic spectral scan framework code from Qualcomm Atheros.

This includes the HAL routines to setup, enable/activate/disable spectral
scan and configure the relevant registers.

This still requires driver interaction to enable spectral scan reporting.
Specifically:

* call ah_spectralConfigure() to configure and enable spectral scan;
* .. there's currently no way to disable spectral scan... that will have
to follow.
* call ah_spectralStart() to force start a spectral report;
* call ah_spectralStop() to force stop an active spectral report.

The spectral scan results appear as PHY errors (type 0x5 on the AR9280,
same as radar) but with the spectral scan bit set (0x10 in the last byte
of the frame) identifying it as a spectral report rather than a radar
FFT report.

Caveats:

* It's likely quite difficult to run spectral _and_ radar at the same
time. Enabling spectral scan disables the radar thresholds but
leaves radar enabled. Thus, the driver (for now) needs to ensure
that only one or the other is enabled.

* .. it needs testing on HT40 mode.

Tested:

* AR9280 in STA mode, HT/20 only

TODO:

* Test on AR9285, AR9287;
* Test in both HT20 and HT40 modes;
* .. all the driver glue.

Obtained from: Qualcomm Atheros

Note why fast frames is disabled for 802.11n NICs now.

It actually works, but net80211 handles A-MPDU and Fast frames
incorrectly; it tries enabling both in some instances, with tragic
results.

Methodise the BT diversity configuration function; so the AR9285
can correctly override it.

This was missed in the previous commit.

Add and tie in the AR5416 bluetooth coexistence methods into the HAL.

Implement a HAL method to set a 64 bit TSF value.

TODO: implement it (and test) for the AR5210/AR5211.

Oops - this was incorrectly removed in a previous commit.

HAL updates!

* Add some more ANI spur immunity levels.
* For AR5111 radios attached to an AR5212, limit the 5GHz channels
that are available. A later revision of the AR5111 supports the 4.9GHz
PSB channels but right now there's no check in place for the radio
revision.

If someone wants PSB support on AR5212+AR5111 radios then please let
me know and I'll add the relevant version check.

Obtained from: Qualcomm Atheros

Flip on half/quarter rate support.

No, this isn't HT/5 and HT/10 support. This is the 11a half/quarter
rate support primarily used by the 4.9GHz and GSM band regulatory
domains.

This is definitely a work in progress.

TODO:

* everything in the last commit;
* lots more interoperability testing with the AR5212 half/quarter rate
support for the relevant chips;
* Do some interop testing on half/quarter rate support between _all_
the 11n chips - AR5416, AR9160, AR9280 (and AR9285/AR9287 when 2GHz
half/quarter rate support is coded up.)

Add default values for the NumTxMaps capability.

Implement an API to fetch the default DFS parameters for the given chip.

The only chip this is currently implemented for is the AR5416 HAL family.
A follow-up commit will add AR5212 support.

PR: kern/170904

Flesh out the multi-rate retry capability.

The existing method for testing for MRR is to call the "SetupXTXDesc"
HAL method and see if it returns AH_TRUE or AH_FALSE. This capability
explicitly lists what number of multi-rate attempts are possible.

"1" means "one rate attempt supported".

Add some AR5416/AR5418 WAR's for power-on and suspend/resume:

* Now that ah_configPCIE is called for both power on and suspend/resume,
make sure the right bit(s) are cleared and set when suspending and
resuming. Specifically:

+ force disable/enable the PCIe PHY upon suspend/resume;
+ reprogram the PCIe WAR register when resuming and upon power-on.

* Add a recipe which powers down any PCIe PHY hardware inside the AR5416
(which is the PCI variant) to save on power. I have (currently) no way
to test exactly how much power is saved, if any.

Tested on:

* AR5416 cardbus - although unfortunately pccard/cbb/cardbus currently
detaches the NIC upon suspend, I don't think it's a proper test case.

* AR5418 PCIe attached to expresscard - since we're not doing PCIe APSM,
it's also not likely a full/good test case.

In both instances I went through a handful of suspend/resume cycles and
ensured that the STA vap reassociated correctly.

TODO:

* Setup a laptop to simply sit in a suspend/resume loop, making sure that
the NIC always correctly comes back;

* Start doing suspend/resume tests with actual traffic going on in the
background, as I bet this process is all quite racy at the present;

* Test adhoc/hostap mode, just to be completely sure it's working correctly;

* See if I can jury rig an external power source to an AR5416 to test out
whether ah_disablePCIE() works.

Obtained from: Qualcomm Atheros

oops - ath_hal_disablepcie is actually destined for another purpose,
not to disable the PCIe PHY in prepration for reset.

Extend the enablepci method to have a "poweroff" flag, which if equal
to true means the hardware is about to go to sleep.

Prepare for improved (read: pcie) suspend/resume support.

* Flesh out the pcie disable method for 11n chips, as they were defaulting
to the AR5212 (empty) PCIe disable method.

* Add accessor macros for the HAL PCIe enable/disable calls.

* Call disable on ath_suspend()

* Call enable on ath_resume()

NOTE:

* This has nothing to do with the NIC sleep/run state - the NIC still
will stay in network-run state rather than supporting network-sleep
state. This is preparation work for supporting correct suspend/resume
WARs for the 11n PCIe NICs.

TODO:

* It may be feasible at this point to keep the chip powered down during
initial probe/attach and only power it up upon the first configure/reset
pass. This however would require correct (for values of "correct")
tracking of the NIC power configuration state from the driver and that
just isn't attempted at the moment.

Tested:

* AR9280 on my Lenovo T60, but with no suspend/resume pass (yet).

Change the MIB cycle count API to return HAL_BOOL, rather than uint32_t,
to return whether it was successful.

Add placeholder (blank) methods for previous chips, for both it and
the 11n extension channel busy call.

Add an AR5416 PCU DMA stop method, as a check for the AR9130 is needed.

The reference driver has a 3ms delay for the AR9130 but I'm not as yet
sure why. From what I can gather, it's likely waiting for some FIFO
flush to occur.

At some point in the future it may be worthwhile adding a WMAC
FIFO flush here, but that'd require some side-call through to the SoC
DDR flush routines.

Obtained from: Atheros

Add placeholder methods for WMI command access (USB, perhaps SDIO later)
which will be needed for AR7010 and AR9287 USB access.

The names differ slightly from Linux and Atheros, for the sake of
consistency.

A lot more work is required in order to convert the 11n HAL support to
fully support USB.

Extend the HAL code to allow the RX and TX chainmask to be overridden
by capabilities.

Add an ar5416SetCapability() function, which contains logic to override
the chainmask and update the relevant stream.

This is designed to be called after the attach function, which presets
the TX/RX chainmask and stream.

TODO: check the chainmask against the hardware chainmask so non-existing
chains aren't enabled.

Support AR9281/AR5B91 - a 1x2 stream device based on the AR9280.

* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.

* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.

The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.

Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.

AR5416 has 14 GPIO pins, from 0->13.

Use the correct RF version probe routine.

Obtained from: Atheros
Sponsored by: Hobnob, Inc.

Introduce a work-around for issues with the AR5416 based MAC on SMP devices.

The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.

This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.

Obtained by: Linux, Atheros

Try to make it more obvious when users are using the PCI or PCIe versions of
the 11n chips.

Add in some more 11n related HAL methods.

Implement the first part of the BB read workaround.

The AR5008/AR9001 series NICs have a bug where BB register reads
will occasionally be corrupted. This could cause issues with things
such as ANI, which adjust operational parameters based on the
BB radio register reads. This was introduced in the AR5008 chip
and fixed with the first released AR9002 series NIC (AR9280v2.)

A followup commit will implement the acutal WAR when reading
BB registers. I'm still not sure how I'll implement it - whether
it should be done in the osdep layer, or whether it should just
live in the AR5416 HAL. Either way, they can use this capability
bit to determine whether to implement the WAR or not.

Thankyou to various sources inside Atheros who have helped me track
down what this particular issue is.

Obtained from: Atheros

Fix a corner case in the HAL debugging changes, where ah was NULL.

Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.

* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed

This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.

Update the TSF and next-TBTT methods to work for the AR5416 and later NICs.
This is another commit in a series of TDMA support fixes for the 11n NICs.

* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.

* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.

* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().

* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.

According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.

The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.

Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)

Add another HAL method - ah_isFastClockEnabled - which returns AH_TRUE
if 5ghz fast clock is enabled in the current operating mode.

It's slightly dirty, but it's part of the reference HAL and used by
the (currently closed-source) radar event code to map radar pulses
back to microsecond durations.

Obtained from: Atheros
Approved by: re (kib, blanket)

Bring over AR5416 specific RX filter get/set routines.

This in particular fixes radar PHY handling - on the AR5212
NIC, one enables the AR_PHY_ERR_RADAR bit in AR_PHY_ERR;
the AR5416 and later also needs a bit set in AR_RX_FILTER.

A follow-up commit is needed to convert the AR5416 ANI code
to use this particular method, as it's currently using the
AR5212 methods directly.

Obtained from: Atheros
Approved by: re (kib)

Re-introduce a global ath_hal_debug again for now, whilst I figure out what
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)

The global ath_hal_debug now affects all instances of the HAL.

This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.

Flesh out a new HAL method to fetch the radar PHY error frame information.

For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.

This information was extracted from the Madwifi DFS branch along with
some local additions.

Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)

For further information, please see:

http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection

This includes references to the relevant patents which describe what
is going on.

Obtained from: Madwifi

Bring over the relevant registers to use when implementing the quiet time
portion of 802.11h.

The AR5212 code has been brought over as a reference, it's currently
untested.

Obtained from: Atheros

Add some missing DFS chipset functionality to the FreeBSD HAL.

Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.

The particulars:

* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.

The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.

Obtained from: Linux, Atheros

Tidy up the ANI API in preparation for looking to expose some more
of the ANI statistics and committing some tools which use these.

* Change HAL_ANI_* commands _back_ to be numerical, rather than a
bitmap;
* modify access to the ANI control bitmap to convert a command to
a bitmap;
* Fix the ANI noise immunity fiddling for CCK errors - it wasn't
checking whether noise immunity was disabled or not.

The ANI control for the AR5416 and later chips was calling ar5212AniControl(),
which did AR5212 specific initialisation. This would cause some slight
silliness when enabling/disabling ANI.

Just to be completely correct - and to ensure the phy error mask/RX filter
register isn't incorrectly played with - make the ANI control function a
method, have it set appropriately for AR5212/AR5416, and call that from the
ANI control interface.

Set this HAL capabilities flag correctly even though it isn't currently
being used.

Make sure the chip is awake before writing to it to finally detach
it.

Obtained from: Atheros

Do a HAL capabilities sync pass based on the Atheros HAL.

* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.

* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.

Read in the extended regulatory domain flags so future code can use them.

These describe FCC/Japan channel and DFS behaviour.

The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.

Break out the PLL setup into an overridable method.

The only method right now is ar5416InitPLL() which handles multiple
chipsets; this can now be overridden by newer chipset HAL code.

Add a HAL capability bit for supporting self-linked RX descriptors and disable it for the 11n chipsets.

From the ath9k source:

==

11N: we can no longer afford to self link the last descriptor.
MAC acknowledges BA status as long as it copies frames to host
buffer (or rx fifo). This can incorrectly acknowledge packets
to a sender if last desc is self-linked.

==

Since this is useful for pre-AR5416 chips that communicate PHY errors
via error frames rather than by on-chip counters, leave the support
in there, but disable it for AR5416 and later.

Flip ANI on for the AR5416 and later chips. I haven't verified it on
the AR9285 so I'll leave it off for that.

Ath9k sources indiciate that one of the ANI modes interferes with
RIFS detection, so match ath9k and disable that.

Bring over an XPA (external power amplifer) bias fix for the AR9160.

This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.

The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.

The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.

Obtained From: Linux ath9k

Back that commit out - something's broken, and I need to figure out
what/why.

This CLKDRV workaround should only be for AR5416 v2.0/2.1;
the check was too strict and enabled it for all non AR5416-v2.2
chipsets - including later ones.

Bring over a copy of the AR5212 TX queue reset and setup routines, in preparation
for fixing them based on the ath9k related TXQ fixes.

I've done this so people can go over the history of the diffs to the original
AR5212 routines (which AR5416 and later chips use) to see what's changed.

Make sure that the AR_MISC_MODE value from the initvals are properly respected.

This commit really is "fix the OFDM duration calculation to match reality when
running in 802.11g mode."

The AR5212 init vals set AR_MISC_MODE to 0x0 and all the bits that can be set are
set through code.

The AR5416 and later initvals set AR_MISC_MODE to various other values (with
the AR5212 AR_MISC_MODE options cleared), which include AR_PCU_CCK_SIFS_MODE .
This adds 6uS to SIFS on non-CCK frames when transmitting.

This fixes the issue where _DATA_ 802.11g OFDM frames were being TX'ed with
the ACK duration set to 38uS, not 44uS as on the AR5212 (and other devices.)

The AR5212 TX pathway obeys the software-programmed duration field in the packet,
but the 11n TX pathway overrides that with a hardware-calculated duration. This
was getting it wrong because of the above AR_MISC_MODE setting. I've verified
that 11g data OFDM frames are now being TXed with the correct ACK+SIFS duration
programmed in.

Introduce methods for the initial calibration and the new PA calibration
routines.

These are needed for the AR9285/AR2427 and AR9287 calibration routines
which will be introducecd in a later commit.

Implement open-loop TX power control (OLC) for Merlin (AR9280) and
generally tidy up the TX power programming code.

Enforce that the TX power offset for Merlin is -5 dBm, rather than
any other value programmable in the EEPROM. This requires some
further code to be ported over from ath9k, so until that is done
and tested, fail to attach NICs whose TX power offset isn't -5
dBm.

This improves both legacy and HT transmission on my merlin board.
It allows for stable MCS TX up to MCS15.

Specifics:

* Refactor out a bunch of the TX power calibration code -
setting/obtaining the power detector / gain boundaries,
programming the PDADC
* Take the -5 dBm TX power offset into account on Merlin -
"0" in the per-rate TX power register means -5 dBm, not
0 dBm
* When doing OLC
* Enforce min (0) and max (AR5416_MAX_RATE_POWER) when fiddling
with the TX power, to avoid the TX power values from wrapping
when low.
* Implement the 1 dBm cck power offset when doing OLC
* Implement temperature compensation for 2.4ghz mode when doing OLC
* Implement an AR9280 specific TX power calibration routine which
includes the OLC twiddles, leaving the earlier chipset path
(AR5416, AR9160) alone

Whilst here, use these refactored routines for the AR9285 TX power
calibration/programming code and enforce correct overflow/underflow
handling when fiddling with TX power values.

Obtained from: linux ath9k

Add a new parameter to selectively enable/disable the ANI operations.

This was inspired by ath9k, which disables ANI anti-noise immunity
parameter tweaking (but leaves the rest of the ANI operations alone.)

Call the right function.

I missed this commit - enable 4k transaction support for the ar5416+ar9160.

Add a new capability which reports the number of spatial streams a device supports.

The higher levels (net80211, if_ath, ath_rate) need this to make correct
choices about what MCS capabilities to advertise and what MCS rates are
able to be TXed.

In summary:

* AR5416 - 2/3 antennas, 2x2 streams
* AR9160 - 2/3 antennas, 2x2 streams
* AR9220 - 2 antennas, 2x2 sstraems
* AR9280 - 2 antennas, 2x2 streams
* AR9285 - 2 antennas but with antenna diversity, 1x1 stream

Bring over some NF calibration changes from ath9k.

Each different radio chipset has a different "good" range of CCA
(clear channel access) parameters where, if you write something
out of range, it's possible the radio will go deaf.

Also, since apparently occasionally reading the NF calibration
returns "wrong" values, so enforce those limits on what is being
written into the CCA register.

Write a default value if there's no history available.

This isn't the case right now but it may be later on when "off-channel"
scanning occurs without init'ing or changing the NF history buffer.
(As each channel may have a different noise floor; so scanning or
other off-channel activity shouldn't affect the NF history of
the current channel.)

Link in the 11n specific TX methods into the HAL.

Fix some typos.

Add missing getCapability call for AR5416.

ANI changes #1 - split out the ANI polling from the RxMonitor hook.

The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.

Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.

Include the initial support for external EEPROMs.

The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.

I believe earlier parts can do something similar but I haven't
experienced it first-hand.

This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.

Add a new HAL method to retrieve the completion schedule. It sets
the completion schedule from the hardware and returns AH_TRUE if
the hardware supports multi-rate retries (AR5212 and above); and
returns AH_FALSE if the hardware doesn't support multi-rate retries.

The sample rate module directly reads the TX completion descriptor
and extracts the TX schedule information from that. It will be
updated in a future commit to instead use this method to determine
the completion schedule.

A new jail(8) with a configuration file, to replace the work currently done
by /etc/rc.d/jail.

MFC r197948 r203156 r203158 r203159 r203680 r203682 r203750 r203882 r203930
r203933 r203959 r204521 r204578:

Atheros AR9285 support.

Bring back AR9285 support. This fixes most of the issues and should be
pretty usable.

MFC after: 1 month

Revert part of the 9285 support because it breaks the 9280 support. I'll
try to do the 9285 support without interfering with any other chipset
revisions support.

Add support for the AR9285 chipset, which is found on many netbooks
available today.

This card is a low power 802.11bgn that only does 11n rates up to MCS 7
(that's 65 Mbps in 20Mhz mode and 135 in 40Mhz mode).
802.11n is not yet supported, but will be in the future.

The driver still has a problem regarding to the setting of txpower on
the card, so don't expect good performance yet. After fixing this
problem, an MFC is possible.

Special thanks to iXsystems and S Smirnov <tonve at yandex.ru> for help
with the purchase of a netbook with this card.

Sponsored by: iXsystems, Inc.

Add HAL_RX_FILTER_BSSID support (to disable bssid match):
o add HAL_CAP_BSSIDMATCH to identify parts that have the support for
disabling bssid match
o honor capability for set/get rx filter
o use HAL_CAP_BSSIDMATCH in driver to decide whether to use the bssid
match disable or fall back to promisc mode

Reviewed by: rpaulo
Approved by: re (rwatson)

add HAL_CAP_INTRMASK to return the set of interrupts supported by the device

preliminary ar9280 support:
o add 9280 attach that sets up ini, cal, etc.
o new rf backend for 9280 and later parts
o split ini setup and spur mitigation support out to methods
and provide 9280-specific support
o minor fixups to shared code to handle 9280-specific work

Obtained from: Atheros (ini values and some code)

move attach debug msg to the rf backend

Add PCIE power control api:
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts

move eeprom attach above first reset as the reset code checks the
eeprom contents for 9280 and later parts

attach methods don't need to be public, make 'em static

5416 and later parts get the radio rev differently; add ar5416GetRadioRev
to do it the right way

remove private copies of gpio methods that were needed when the hal
was an independent entity