MFC r363900:
Fix typo.

MFC r337783:
Implement a limit on on the number of IPv6 reassembly queues per bucket.

There is a hashing algorithm which should distribute IPv6 reassembly
queues across the available buckets in a relatively even way. However,
if there is a flaw in the hashing algorithm which allows a large number
of IPv6 fragment reassembly queues to end up in a single bucket, a per-
bucket limit could help mitigate the performance impact of this flaw.

Implement such a limit, with a default of twice the maximum number of
reassembly queues divided by the number of buckets. Recalculate the
limit any time the maximum number of reassembly queues changes.
However, allow the user to override the value using a sysctl
(net.inet6.ip6.maxfragbucketsize).

Approved by: so
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923

MFC r337782:
Add a limit of the number of fragments per IPv6 packet.

The IPv4 fragment reassembly code supports a limit on the number of
fragments per packet. The default limit is currently 17 fragments.
Among other things, this limit serves to limit the number of fragments
the code must parse when trying to reassembly a packet.

Add a limit to the IPv6 reassembly code. By default, limit a packet
to 65 fragments (64 on the queue, plus one final fragment to complete
the packet). This allows an average fragment size of 1,008 bytes, which
should be sufficient to hold a fragment. (Recall that the IPv6 minimum
MTU is 1280 bytes. Therefore, this configuration allows a full-size
IPv6 packet to be fragmented on a link with the minimum MTU and still
carry approximately 272 bytes of headers before the fragmented portion
of the packet.)

Users can adjust this limit using the net.inet6.ip6.maxfragsperpacket
sysctl.

Approved by: so
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923

MFC r337781:
Make the IPv6 fragment limits be global, rather than per-VNET, limits.

The IPv6 reassembly fragment limit is based on the number of mbuf clusters,
which are a global resource. However, the limit is currently applied
on a per-VNET basis. Given enough VNETs (or given sufficient customization
on enough VNETs), it is possible that the sum of all the VNET fragment
limits will exceed the number of mbuf clusters available in the system.

Given the fact that the fragment limits are intended (at least in part) to
regulate access to a global resource, the IPv6 fragment limit should
be applied on a global basis.

Note that it is still possible to disable fragmentation for a particular
VNET by setting the net.inet6.ip6.maxfragpackets sysctl to 0 for that
VNET. In addition, it is now possible to disable fragmentation globally
by setting the net.inet6.ip6.maxfrags sysctl to 0.

Approved by: so
Security: FreeBSD-SA-18:10.ip
Security: CVE-2018-6923

MFC r334324:
Remove empty encap_init() function.

Revert r330897:

This was intended to be a non-functional change. It wasn't. The commit
message was thus wrong. In addition it broke arm, and merged crypto
related code.

Revert with prejudice.

This revert skips files touched in r316370 since that commit was since
MFCed. This revert also skips files that require $FreeBSD$ property
changes.

Thank you to those who helped me get out of this mess including but not
limited to gonzo, kevans, rgrimes.

Requested by: gjb (re)

Partial merge of the SPDX changes

These changes are incomplete but are making it difficult
to determine what other changes can/should be merged.

No objections from: pfg

MFC r304572 (by bz):
Remove the kernel optoion for IPSEC_FILTERTUNNEL, which was deprecated
more than 7 years ago in favour of a sysctl in r192648.

MFC r305122:
Remove redundant sanity checks from ipsec[46]_common_input_cb().

This check already has been done in the each protocol callback.

MFC r309144,309174,309201 (by fabient):
IPsec RFC6479 support for replay window sizes up to 2^32 - 32 packets.

Since the previous algorithm, based on bit shifting, does not scale
with large replay windows, the algorithm used here is based on
RFC 6479: IPsec Anti-Replay Algorithm without Bit Shifting.
The replay window will be fast to be updated, but will cost as many bits
in RAM as its size.

The previous implementation did not provide a lock on the replay window,
which may lead to replay issues.

Obtained from: emeric.poupon@stormshield.eu
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D8468

MFC r309143,309146 (by fabient):
In a dual processor system (2*6 cores) during IPSec throughput tests,
we see a lot of contention on the arc4 lock, used to generate the IV
of the ESP output packets.

The idea of this patch is to split this mutex in order to reduce the
contention on this lock.

Update r309143 to prevent false sharing.

Reviewed by: delphij, markm, ache
Approved by: so
Obtained from: emeric.poupon@stormshield.eu
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D8130

MFC r313330:
Merge projects/ipsec into head/.

Small summary
-------------

o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.

Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352

MFC r313331:
Add removed headers into the ObsoleteFiles.inc.

MFC r313561 (by glebius):
Move tcp_fields_to_net() static inline into tcp_var.h, just below its
friend tcp_fields_to_host(). There is third party code that also uses
this inline.

MFC r313697:
Remove IPsec related PCB code from SCTP.

The inpcb structure has inp_sp pointer that is initialized by
ipsec_init_pcbpolicy() function. This pointer keeps strorage for IPsec
security policies associated with a specific socket.
An application can use IP_IPSEC_POLICY and IPV6_IPSEC_POLICY socket
options to configure these security policies. Then ip[6]_output()
uses inpcb pointer to specify that an outgoing packet is associated
with some socket. And IPSEC_OUTPUT() method can use a security policy
stored in the inp_sp. For inbound packet the protocol-specific input
routine uses IPSEC_CHECK_POLICY() method to check that a packet conforms
to inbound security policy configured in the inpcb.

SCTP protocol doesn't specify inpcb for ip[6]_output() when it sends
packets. Thus IPSEC_OUTPUT() method does not consider such packets as
associated with some socket and can not apply security policies
from inpcb, even if they are configured. Since IPSEC_CHECK_POLICY()
method is called from protocol-specific input routine, it can specify
inpcb pointer and associated with socket inbound policy will be
checked. But there are two problems:
1. Such check is asymmetric, becasue we can not apply security policy
from inpcb for outgoing packet.
2. IPSEC_CHECK_POLICY() expects that caller holds INPCB lock and
access to inp_sp is protected. But for SCTP this is not correct,
becasue SCTP uses own locks to protect inpcb.

To fix these problems remove IPsec related PCB code from SCTP.
This imply that IP_IPSEC_POLICY and IPV6_IPSEC_POLICY socket options
will be not applicable to SCTP sockets. To be able correctly check
inbound security policies for SCTP, mark its protocol header with
the PR_LASTHDR flag.

Differential Revision: https://reviews.freebsd.org/D9538

MFC r313746:
Add missing check to fix the build with IPSEC_SUPPORT and without MAC.

MFC r313805:
Fix LINT build for powerpc.

Build kernel modules support only when both IPSEC and TCP_SIGNATURE
are not defined.

MFC r313922:
For translated packets do not adjust UDP checksum if it is zero.

In case when decrypted and decapsulated packet is an UDP datagram,
check that its checksum is not zero before doing incremental checksum
adjustment.

MFC r314339:
Document that the size of AH ICV for HMAC-SHA2-NNN should be half of
NNN bits as described in RFC4868.

PR: 215978

MFC r314812:
Introduce the concept of IPsec security policies scope.

Currently are defined three scopes: global, ifnet, and pcb.
Generic security policies that IKE daemon can add via PF_KEY interface
or an administrator creates with setkey(8) utility have GLOBAL scope.
Such policies can be applied by the kernel to outgoing packets and checked
agains inbound packets after IPsec processing.
Security policies created by if_ipsec(4) interfaces have IFNET scope.
Such policies are applied to packets that are passed through if_ipsec(4)
interface.
And security policies created by application using setsockopt()
IP_IPSEC_POLICY option have PCB scope. Such policies are applied to
packets related to specific socket. Currently there is no way to list
PCB policies via setkey(8) utility.

Modify setkey(8) and libipsec(3) to be able distinguish the scope of
security policies in the `setkey -DP` listing. Add two optional flags:
'-t' to list only policies related to virtual *tunneling* interfaces,
i.e. policies with IFNET scope, and '-g' to list only policies with GLOBAL
scope. By default policies from all scopes are listed.

To implement this PF_KEY's sadb_x_policy structure was modified.
sadb_x_policy_reserved field is used to pass the policy scope from the
kernel to userland. SADB_SPDDUMP message extended to support filtering
by scope: sadb_msg_satype field is used to specify bit mask of requested
scopes.

For IFNET policies the sadb_x_policy_priority field of struct sadb_x_policy
is used to pass if_ipsec's interface if_index to the userland. For GLOBAL
policies sadb_x_policy_priority is used only to manage order of security
policies in the SPDB. For IFNET policies it is not used, so it can be used
to keep if_index.

After this change the output of `setkey -DP` now looks like:
# setkey -DPt
0.0.0.0/0[any] 0.0.0.0/0[any] any
in ipsec
esp/tunnel/87.250.242.144-87.250.242.145/unique:145
spid=7 seq=3 pid=58025 scope=ifnet ifname=ipsec0
refcnt=1
# setkey -DPg
::/0 ::/0 icmp6 135,0
out none
spid=5 seq=1 pid=872 scope=global
refcnt=1

Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9805

PR: 212018
Relnotes: yes
Sponsored by: Yandex LLC

MFC r312307:
Improve some of the sysctl descriptions added in r299827.

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

The pr_destroy field does not allow us to run the teardown code in a
specific order. VNET_SYSUNINITs however are doing exactly that.
Thus remove the VIMAGE conditional field from the domain(9) protosw
structure and replace it with VNET_SYSUNINITs.
This also allows us to change some order and to make the teardown functions
file local static.
Also convert divert(4) as it uses the same mechanism ip(4) and ip6(4) use
internally.

Slightly reshuffle the SI_SUB_* fields in kernel.h and add a new ones, e.g.,
for pfil consumers (firewalls), partially for this commit and for others
to come.

Reviewed by: gnn, tuexen (sctp), jhb (kernel.h)
Obtained from: projects/vnet
MFC after: 2 weeks
X-MFC: do not remove pr_destroy
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6652

Add PR_CONNREQUIRED for SOCK_STREAM sockets using SCTP.

This is required to signal connetion setup on non-blocking sockets
via becoming writable. This still allows for implicit connection
setup.

MFC after: 1 week

Add sysctl descriptions for net.inet6.ip6 and net.inet6.icmp6.

icmp6.redirtimeout, icmp6.nd6_maxnudhint and ip6.rr_prune are left
undocumented as they appear to have no effect. Some existing sysctl
descriptions were modified for consistency and style, and the
ip6.tempvltime and ip6.temppltime handlers were rewritten to be a bit
simpler and to avoid setting the sysctl value before validating it.

MFC after: 3 weeks

Indentation issues.

Contract some lines leftover from r298310.

Mea culpa.

kernel: use our nitems() macro when it is available through param.h.

No functional change, only trivial cases are done in this sweep,

Discussed in: freebsd-current

These files were getting sys/malloc.h and vm/uma.h with header pollution
via sys/mbuf.h

Renove faith(4) and faithd(8) from base. It looks like industry
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.

No objections from: net@

Overhaul if_gre(4).

Split it into two modules: if_gre(4) for GRE encapsulation and
if_me(4) for minimal encapsulation within IP.

gre(4) changes:
* convert to if_transmit;
* rework locking: protect access to softc with rmlock,
protect from concurrent ioctls with sx lock;
* correct interface accounting for outgoing datagramms (count only payload size);
* implement generic support for using IPv6 as delivery header;
* make implementation conform to the RFC 2784 and partially to RFC 2890;
* add support for GRE checksums - calculate for outgoing datagramms and check
for inconming datagramms;
* add support for sending sequence number in GRE header;
* remove support of cached routes. This fixes problem, when gre(4) doesn't
work at system startup. But this also removes support for having tunnels with
the same addresses for inner and outer header.
* deprecate support for various GREXXX ioctls, that doesn't used in FreeBSD.
Use our standard ioctls for tunnels.

me(4):
* implementation conform to RFC 2004;
* use if_transmit;
* use the same locking model as gre(4);

PR: 164475
Differential Revision: D1023
No objections from: net@
Relnotes: yes
Sponsored by: Yandex LLC

Remove SYSCTL_VNET_* macros, and simply put CTLFLAG_VNET where needed.

Sponsored by: Nginx, Inc.

Remove VNET_SYSCTL_ARG(). The generic sysctl(9) code handles that.

Reviewed by: ae
Sponsored by: Nginx, Inc.

Finish r274118: remove useless fields from struct domain.

Sponsored by: Yandex LLC

Make checks for rt_mtu generic:

Some virtual if drivers has (ab)used ifa ifa_rtrequest hook to enforce
route MTU to be not bigger that interface MTU. While ifa_rtrequest hooking
might be an option in some situation, it is not feasible to do MTU checks
there: generic (or per-domain) routing code is perfectly capable of doing
this.

We currrently have 3 places where MTU is altered:

1) route addition.
In this case domain overrides radix _addroute callback (in[6]_addroute)
and all necessary checks/fixes are/can be done there.

2) route change (especially, GW change).
In this case, there are no explicit per-domain calls, but one can
override rte by setting ifa_rtrequest hook to domain handler
(inet6 does this).

3) ifconfig ifaceX mtu YYYY
In this case, we have no callbacks, but ip[6]_output performes runtime
checks and decreases rt_mtu if necessary.

Generally, the goals are to be able to handle all MTU changes in
control plane, not in runtime part, and properly deal with increased
interface MTU.

This commit changes the following:
* removes hooks setting MTU from drivers side
* adds proper per-doman MTU checks for case 1)
* adds generic MTU check for case 2)

* The latter is done by using new dom_ifmtu callback since
if_mtu denotes L3 interface MTU, e.g. maximum trasmitted _packet_ size.
However, IPv6 mtu might be different from if_mtu one (e.g. default 1280)
for some cases, so we need an abstract way to know maximum MTU size
for given interface and domain.
* moves rt_setmetrics() before MTU/ifa_rtrequest hooks since it copies
user-supplied data which must be checked.
* removes RT_LOCK_ASSERT() from other ifa_rtrequest hooks to be able to
use this functions on new non-inserted rte.

More changes will follow soon.

MFC after: 1 month
Sponsored by: Yandex LLC

Change pr_output's prototype to avoid the need for explicit casts.
This is a follow up to r269699.

Phabric: D564
Reviewed by: jhb

Merge 'struct ip6protosw' and 'struct protosw' into one. Now we have
only one protocol switch structure that is shared between ipv4 and ipv6.

Phabric: D476
Reviewed by: jhb

Minor style cleanups.

Add support for UDP-Lite protocol (RFC 3828) to IPv4 and IPv6 stacks.
Tested with vlc and a test suite [1].

[1] http://www.erg.abdn.ac.uk/~gerrit/udp-lite/files/udplite_linux.tar.gz

Reviewed by: jhb, glebius, adrian

o Revamp API between flowtable and netinet, netinet6.
- ip_output() and ip_output6() simply call flowtable_lookup(),
passing mbuf and address family. That's the only code under
#ifdef FLOWTABLE in the protocols code now.
o Revamp statistics gathering and export.
- Remove hand made pcpu stats, and utilize counter(9).
- Snapshot of statistics is available via 'netstat -rs'.
- All sysctls are moved into net.flowtable namespace, since
spreading them over net.inet isn't correct.
o Properly separate at compile time INET and INET6 parts.
o General cleanup.
- Remove chain of multiple flowtables. We simply have one for
IPv4 and one for IPv6.
- Flowtables are allocated in flowtable.c, symbols are static.
- With proper argument to SYSINIT() we no longer need flowtable_ready.
- Hash salt doesn't need to be per-VNET.
- Removed rudimentary debugging, which use quite useless in dtrace era.

The runtime behavior of flowtable shouldn't be changed by this commit.

Sponsored by: Netflix
Sponsored by: Nginx, Inc.

The r48589 promised to remove implicit inclusion of if_var.h soon. Prepare
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h

Sponsored by: Netflix
Sponsored by: Nginx, Inc.

Migrate structs ip6stat, icmp6stat and rip6stat to PCPU counters.

Use FF02:0:0:0:0:2:FF00::/104 prefix for IPv6 Node Information Group
Address. Although KAME implementation used FF02:0:0:0:0:2::/96 based on
older versions of draft-ietf-ipngwg-icmp-name-lookup, it has been changed
in RFC 4620.

The kernel always joins the /104-prefixed address, and additionally does
/96-prefixed one only when net.inet6.icmp6.nodeinfo_oldmcprefix=1.
The default value of the sysctl is 1.

ping6(8) -N flag now uses /104-prefixed one. When this flag is specified
twice, it uses /96-prefixed one instead.

Reviewed by: ume
Based on work by: Thomas Scheffler
PR: conf/174957
MFC after: 2 weeks

Remove unused global variables.

Reviewed by: ae, glebius

o Convert IPv6 read-only stats sysctls to the read-write ones.
o Teach netstat(1) -z to reset these stats sysctls.

PR: bin/153206
Reviewed by: glebuis
Sponsored by: NGINX, Inc.
MFC after: 1 month

Add $ipv6_cpe_wanif to enable functionality required for IPv6 CPE
(r225485). When setting an interface name to it, the following
configurations will be enabled:

1. "no_radr" is set to all IPv6 interfaces automatically.

2. "-no_radr accept_rtadv" will be set only for $ipv6_cpe_wanif. This is
done just before evaluating $ifconfig_IF_ipv6 in the rc.d scripts (this
means you can manually supersede this configuration if necessary).

3. The node will add RA-sending routers to the default router list
even if net.inet6.ip6.forwarding=1.

This mode is added to conform to RFC 6204 (a router which connects
the end-user network to a service provider network). To enable
packet forwarding, you still need to set ipv6_gateway_enable=YES.

Note that accepting router entries into the default router list when
packet forwarding capability and a routing daemon are enabled can
result in messing up the routing table. To minimize such unexpected
behaviors, "no_radr" is set on all interfaces but $ipv6_cpe_wanif.

Approved by: re (bz)

The socket API only specifies SCTP for SOCK_SEQPACKET and
SOCK_STREAM, but not SOCK_DGRAM. So don't register it for
SOCK_DGRAM.
While there, fix some indentation.

- Accept Router Advertisement messages even when net.inet6.ip6.forwarding=1.

- A new per-interface knob IFF_ND6_NO_RADR and sysctl IPV6CTL_NO_RADR.
This controls if accepting a route in an RA message as the default route.
The default value for each interface can be set by net.inet6.ip6.no_radr.
The system wide default value is 0.

- A new sysctl: net.inet6.ip6.norbit_raif. This controls if setting R-bit in
NA on RA accepting interfaces. The default is 0 (R-bit is set based on
net.inet6.ip6.forwarding).

Background:

IPv6 host/router model suggests a router sends an RA and a host accepts it for
router discovery. Because of that, KAME implementation does not allow
accepting RAs when net.inet6.ip6.forwarding=1. Accepting RAs on a router can
make the routing table confused since it can change the default router
unintentionally.

However, in practice there are cases where we cannot distinguish a host from
a router clearly. For example, a customer edge router often works as a host
against the ISP, and as a router against the LAN at the same time. Another
example is a complex network configurations like an L2TP tunnel for IPv6
connection to Internet over an Ethernet link with another native IPv6 subnet.
In this case, the physical interface for the native IPv6 subnet works as a
host, and the pseudo-interface for L2TP works as the default IP forwarding
route.

Problem:

Disabling processing RA messages when net.inet6.ip6.forwarding=1 and
accepting them when net.inet6.ip6.forward=0 cause the following practical
issues:

- A router cannot perform SLAAC. It becomes a problem if a box has
multiple interfaces and you want to use SLAAC on some of them, for
example. A customer edge router for IPv6 Internet access service
using an IPv6-over-IPv6 tunnel sometimes needs SLAAC on the
physical interface for administration purpose; updating firmware
and so on (link-local addresses can be used there, but GUAs by
SLAAC are often used for scalability).

- When a host has multiple IPv6 interfaces and it receives multiple RAs on
them, controlling the default route is difficult. Router preferences
defined in RFC 4191 works only when the routers on the links are
under your control.

Details of Implementation Changes:

Router Advertisement messages will be accepted even when
net.inet6.ip6.forwarding=1. More precisely, the conditions are as
follow:

(ACCEPT_RTADV && !NO_RADR && !ip6.forwarding)
=> Normal RA processing on that interface. (as IPv6 host)

(ACCEPT_RTADV && (NO_RADR || ip6.forwarding))
=> Accept RA but add the router to the defroute list with
rtlifetime=0 unconditionally. This effectively prevents
from setting the received router address as the box's
default route.

(!ACCEPT_RTADV)
=> No RA processing on that interface.

ACCEPT_RTADV and NO_RADR are per-interface knob. In short, all interface
are classified as "RA-accepting" or not. An RA-accepting interface always
processes RA messages regardless of ip6.forwarding. The difference caused by
NO_RADR or ip6.forwarding is whether the RA source address is considered as
the default router or not.

R-bit in NA on the RA accepting interfaces is set based on
net.inet6.ip6.forwarding. While RFC 6204 W-1 rule (for CPE case) suggests
a router should disable the R-bit completely even when the box has
net.inet6.ip6.forwarding=1, I believe there is no technical reason with
doing so. This behavior can be set by a new sysctl net.inet6.ip6.norbit_raif
(the default is 0).

Usage:

# ifconfig fxp0 inet6 accept_rtadv
=> accept RA on fxp0
# ifconfig fxp0 inet6 accept_rtadv no_radr
=> accept RA on fxp0 but ignore default route information in it.
# sysctl net.inet6.ip6.norbit_no_radr=1
=> R-bit in NAs on RA accepting interfaces will always be set to 0.

Add FEATURE() definitions for IPv4 and IPv6 so that we can use
feature_present(3) to dynamically decide whether to use one or the
other family.

Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 10 days

MFp4 CH=191760,191770:

Not compiling in and not initializing from inetsw from in_proto.c for
IPv6 only, we need to initialize upper layer protocols from inet6sw.
Make sure to not initialize them twice in a Dual-Stack
environment but only conditionally on no INET as we have done for
TCP for a long time. Otherwise we would leak resources.

Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days

Allow carp(4) to be loaded as a kernel module. Follow precedent set by
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.

Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.

This commit requires IP6PROTOSPACER, introduced in r211115.

Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks

MFp4 CH180235:

Add proto spacers to inet6sw like we have for legacy IP. This allows us
to dynamically pf_proto_register() for INET6 from modules, needed by
upcoming CARP changes and SeND.
MC and SCTP could make use of it as well in theory in the future after
upcoming VIMAGE vnet teardown work.

Discussed with: will, anchie
MFC after: 10 days

Add flowtable support to IPv6

Tested by: qingli@

Reviewed by: qingli@
MFC after: 3 days

MFP4: @176978-176982, 176984, 176990-176994, 177441

"Whitspace" churn after the VIMAGE/VNET whirls.

Remove the need for some "init" functions within the network
stack, like pim6_init(), icmp_init() or significantly shorten
others like ip6_init() and nd6_init(), using static initialization
again where possible and formerly missed.

Move (most) variables back to the place they used to be before the
container structs and VIMAGE_GLOABLS (before r185088) and try to
reduce the diff to stable/7 and earlier as good as possible,
to help out-of-tree consumers to update from 6.x or 7.x to 8 or 9.

This also removes some header file pollution for putatively
static global variables.

Revert VIMAGE specific changes in ipfilter::ip_auth.c, that are
no longer needed.

Reviewed by: jhb
Discussed with: rwatson
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 6 days

Garbage collect references to the no longer implemented tcp_fasttimo().

Discussed with: rwatson
MFC after: 5 days

Improve flexibility of receiving Router Advertisement and
automatic link-local address configuration:

- Convert a sysctl net.inet6.ip6.accept_rtadv to one for the
default value of a per-IF flag ND6_IFF_ACCEPT_RTADV, not a
global knob. The default value of the sysctl is 0.

- Add a new per-IF flag ND6_IFF_AUTO_LINKLOCAL and convert a
sysctl net.inet6.ip6.auto_linklocal to one for its default
value. The default value of the sysctl is 1.

- Make ND6_IFF_IFDISABLED more robust. It can be used to disable
IPv6 functionality of an interface now.

- Receiving RA is allowed if ip6_forwarding==0 *and*
ND6_IFF_ACCEPT_RTADV is set on that interface. The former
condition will be revisited later to support a "host + router" box
like IPv6 CPE router. The current behavior is compatible with
the older releases of FreeBSD.

- The ifconfig(8) now supports these ND6 flags as well as "nud",
"prefer_source", and "disabled" in ndp(8). The ndp(8) now
supports "auto_linklocal".

Discussed with: bz and jinmei
Reviewed by: bz
MFC after: 3 days

Merge the remainder of kern_vimage.c and vimage.h into vnet.c and
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.

Reviewed by: bz
Approved by: re (vimage blanket)

Introduce and use a sysinit-based initialization scheme for virtual
network stacks, VNET_SYSINIT:

- Add VNET_SYSINIT and VNET_SYSUNINIT macros to declare events that will
occur each time a network stack is instantiated and destroyed. In the
!VIMAGE case, these are simply mapped into regular SYSINIT/SYSUNINIT.
For the VIMAGE case, we instead use SYSINIT's to track their order and
properties on registration, using them for each vnet when created/
destroyed, or immediately on module load for already-started vnets.
- Remove vnet_modinfo mechanism that existed to serve this purpose
previously, as well as its dependency scheme: we now just use the
SYSINIT ordering scheme.
- Implement VNET_DOMAIN_SET() to allow protocol domains to declare that
they want init functions to be called for each virtual network stack
rather than just once at boot, compiling down to DOMAIN_SET() in the
non-VIMAGE case.
- Walk all virtualized kernel subsystems and make use of these instead
of modinfo or DOMAIN_SET() for init/uninit events. In some cases,
convert modular components from using modevent to using sysinit (where
appropriate). In some cases, do minor rejuggling of SYSINIT ordering
to make room for or better manage events.

Portions submitted by: jhb (VNET_SYSINIT), bz (cleanup)
Discussed with: jhb, bz, julian, zec
Reviewed by: bz
Approved by: re (VIMAGE blanket)

sysctl_msec_to_ticks is used with both virtualized and
non-vrtiualized sysctls so we cannot used one common function.

Add a macro to convert the arg1 in the virtualized case to
vnet.h to not expose the maths to all over the code.

Add a wrapper for the single virtualized call, properly handling
arg1 and call the default implementation from there.

Convert the two over places to use the new macro.

Reviewed by: rwatson
Approved by: re (kib)

Build on Jeff Roberson's linker-set based dynamic per-CPU allocator
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.

Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.

Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.

This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.

Bump __FreeBSD_version and update UPDATING.

Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)

Add explicit includes for jail.h to the files that need them and
remove the "hidden" one from vimage.h.

After r193232 rt_tables in vnet.h are no longer indirectly dependent on
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.

Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.

Introduce an infrastructure for dismantling vnet instances.

Vnet modules and protocol domains may now register destructor
functions to clean up and release per-module state. The destructor
mechanisms can be triggered by invoking "vimage -d", or a future
equivalent command which will be provided via the new jail framework.

While this patch introduces numerous placeholder destructor functions,
many of those are currently incomplete, thus leaking memory or (even
worse) failing to stop all running timers. Many of such issues are
already known and will be incrementaly fixed over the next weeks in
smaller incremental commits.

Apart from introducing new fields in structs ifnet, domain, protosw
and vnet_net, which requires the kernel and modules to be rebuilt, this
change should have no impact on nooptions VIMAGE builds, since vnet
destructors can only be called in VIMAGE kernels. Moreover,
destructor functions should be in general compiled in only in
options VIMAGE builds, except for kernel modules which can be safely
kldunloaded at run time.

Bump __FreeBSD_version to 800097.
Reviewed by: bz, julian
Approved by: rwatson, kib (re), julian (mentor)

Permit buiding kernels with options VIMAGE, restricted to only a single
active network stack instance. Turning on options VIMAGE at compile
time yields the following changes relative to default kernel build:

1) V_ accessor macros for virtualized variables resolve to structure
fields via base pointers, instead of being resolved as fields in global
structs or plain global variables. As an example, V_ifnet becomes:

options VIMAGE: ((struct vnet_net *) vnet_net)->_ifnet
default build: vnet_net_0._ifnet
options VIMAGE_GLOBALS: ifnet

2) INIT_VNET_* macros will declare and set up base pointers to be used
by V_ accessor macros, instead of resolving to whitespace:

INIT_VNET_NET(ifp->if_vnet); becomes

struct vnet_net *vnet_net = (ifp->if_vnet)->mod_data[VNET_MOD_NET];

3) Memory for vnet modules registered via vnet_mod_register() is now
allocated at run time in sys/kern/kern_vimage.c, instead of per vnet
module structs being declared as globals. If required, vnet modules
can now request the framework to provide them with allocated bzeroed
memory by filling in the vmi_size field in their vmi_modinfo structures.

4) structs socket, ifnet, inpcbinfo, tcpcb and syncache_head are
extended to hold a pointer to the parent vnet. options VIMAGE builds
will fill in those fields as required.

5) curvnet is introduced as a new global variable in options VIMAGE
builds, always pointing to the default and only struct vnet.

6) struct sysctl_oid has been extended with additional two fields to
store major and minor virtualization module identifiers, oid_v_subs and
oid_v_mod. SYSCTL_V_* family of macros will fill in those fields
accordingly, and store the offset in the appropriate vnet container
struct in oid_arg1.
In sysctl handlers dealing with virtualized sysctls, the
SYSCTL_RESOLVE_V_ARG1() macro will compute the address of the target
variable and make it available in arg1 variable for further processing.

Unused fields in structs vnet_inet, vnet_inet6 and vnet_ipfw have
been deleted.

Reviewed by: bz, rwatson
Approved by: julian (mentor)

Bite the bullet, and make the IPv6 SSM and MLDv2 mega-commit:
import from p4 bms_netdev. Summary of changes:

* Connect netinet6/in6_mcast.c to build.
The legacy KAME KPIs are mostly preserved.
* Eliminate now dead code from ip6_output.c.
Don't do mbuf bingo, we are not going to do RFC 2292 style
CMSG tricks for multicast options as they are not required
by any current IPv6 normative reference.
* Refactor transports (UDP, raw_ip6) to do own mcast filtering.
SCTP, TCP unaffected by this change.
* Add ip6_msource, in6_msource structs to in6_var.h.
* Hookup mld_ifinfo state to in6_ifextra, allocate from
domifattach path.
* Eliminate IN6_LOOKUP_MULTI(), it is no longer referenced.
Kernel consumers which need this should use in6m_lookup().
* Refactor IPv6 socket group memberships to use a vector (like IPv4).
* Update ifmcstat(8) for IPv6 SSM.
* Add witness lock order for IN6_MULTI_LOCK.
* Move IN6_MULTI_LOCK out of lower ip6_output()/ip6_input() paths.
* Introduce IP6STAT_ADD/SUB/INC/DEC as per rwatson's IPv4 cleanup.
* Update carp(4) for new IPv6 SSM KPIs.
* Virtualize ip6_mrouter socket.
Changes mostly localized to IPv6 MROUTING.
* Don't do a local group lookup in MROUTING.
* Kill unused KAME prototypes in6_purgemkludge(), in6_restoremkludge().
* Preserve KAME DAD timer jitter behaviour in MLDv1 compatibility mode.
* Bump __FreeBSD_version to 800084.
* Update UPDATING.

NOTE WELL:
* This code hasn't been tested against real MLDv2 queriers
(yet), although the on-wire protocol has been verified in Wireshark.
* There are a few unresolved issues in the socket layer APIs to
do with scope ID propagation.
* There is a LOR present in ip6_output()'s use of
in6_setscope() which needs to be resolved. See comments in mld6.c.
This is believed to be benign and can't be avoided for the moment
without re-introducing an indirect netisr.

This work was mostly derived from the IGMPv3 implementation, and
has been sponsored by a third party.

For all files including net/vnet.h directly include opt_route.h and
net/route.h.

Remove the hidden include of opt_route.h and net/route.h from net/vnet.h.

We need to make sure that both opt_route.h and net/route.h are included
before net/vnet.h because of the way MRT figures out the number of FIBs
from the kernel option. If we do not, we end up with the default number
of 1 when including net/vnet.h and array sizes are wrong.

This does not change the list of files which depend on opt_route.h
but we can identify them now more easily.

Put a global variables, which were virtualized but formerly
missed under VIMAGE_GLOBAL.

Start putting the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.

While there garbage collect a few dead externs from ip6_var.h.

Sponsored by: The FreeBSD Foundation

Conditionally compile out V_ globals while instantiating the appropriate
container structures, depending on VIMAGE_GLOBALS compile time option.

Make VIMAGE_GLOBALS a new compile-time option, which by default will not
be defined, resulting in instatiations of global variables selected for
V_irtualization (enclosed in #ifdef VIMAGE_GLOBALS blocks) to be
effectively compiled out. Instantiate new global container structures
to hold V_irtualized variables: vnet_net_0, vnet_inet_0, vnet_inet6_0,
vnet_ipsec_0, vnet_netgraph_0, and vnet_gif_0.

Update the VSYM() macro so that depending on VIMAGE_GLOBALS the V_
macros resolve either to the original globals, or to fields inside
container structures, i.e. effectively

#ifdef VIMAGE_GLOBALS
#define V_rt_tables rt_tables
#else
#define V_rt_tables vnet_net_0._rt_tables
#endif

Update SYSCTL_V_*() macros to operate either on globals or on fields
inside container structs.

Extend the internal kldsym() lookups with the ability to resolve
selected fields inside the virtualization container structs. This
applies only to the fields which are explicitly registered for kldsym()
visibility via VNET_MOD_DECLARE() and vnet_mod_register(), currently
this is done only in sys/net/if.c.

Fix a few broken instances of MODULE_GLOBAL() macro use in SCTP code,
and modify the MODULE_GLOBAL() macro to resolve to V_ macros, which in
turn result in proper code being generated depending on VIMAGE_GLOBALS.

De-virtualize local static variables in sys/contrib/pf/net/pf_subr.c
which were prematurely V_irtualized by automated V_ prepending scripts
during earlier merging steps. PF virtualization will be done
separately, most probably after next PF import.

Convert a few variable initializations at instantiation to
initialization in init functions, most notably in ipfw. Also convert
TUNABLE_INT() initializers for V_ variables to TUNABLE_FETCH_INT() in
initializer functions.

Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation

Rather than using hidden includes (with cicular dependencies),
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.

For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.

Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation

Merge more of currently non-functional (i.e. resolving to
whitespace) macros from p4/vimage branch.

Do a better job at enclosing all instantiations of globals
scheduled for virtualization in #ifdef VIMAGE_GLOBALS blocks.

De-virtualize and mark as const saorder_state_alive and
saorder_state_any arrays from ipsec code, given that they are never
updated at runtime, so virtualizing them would be pointless.

Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation

Change the initialization methodology for global variables scheduled
for virtualization.

Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.

Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.

Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation

Step 1.5 of importing the network stack virtualization infrastructure
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit

Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.

Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().

Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).

All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).

(*) netipsec/keysock.c did not validate depending on compile time options.

Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation

Default to ignoring potentially evil IPv6 Neighbor Solicitation
messages.

Approved by: so (cperciva)
Approved by: re (kensmith)
Security: FreeBSD-SA-08:10.nd6
Thanks to: jinmei, bz

Commit step 1 of the vimage project, (network stack)
virtualization work done by Marko Zec (zec@).

This is the first in a series of commits over the course
of the next few weeks.

Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.

We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.

Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch

This patch provides the back end support for equal-cost multi-path
(ECMP) for both IPv4 and IPv6. Previously, multipath route insertion
is disallowed. For example,

route add -net 192.103.54.0/24 10.9.44.1
route add -net 192.103.54.0/24 10.9.44.2

The second route insertion will trigger an error message of
"add net 192.103.54.0/24: gateway 10.2.5.2: route already in table"

Multiple default routes can also be inserted. Here is the netstat
output:

default 10.2.5.1 UGS 0 3074 bge0 =>
default 10.2.5.2 UGS 0 0 bge0

When multipath routes exist, the "route delete" command requires
a specific gateway to be specified or else an error message would
be displayed. For example,

route delete default

would fail and trigger the following error message:

"route: writing to routing socket: No such process"
"delete net default: not in table"

On the other hand,

route delete default 10.2.5.2

would be successful: "delete net default: gateway 10.2.5.2"

One does not have to specify a gateway if there is only a single
route for a particular destination.

I need to perform more testings on address aliases and multiple
interfaces that have the same IP prefixes. This patch as it
stands today is not yet ready for prime time. Therefore, the ECMP
code fragments are fully guarded by the RADIX_MPATH macro.
Include the "options RADIX_MPATH" in the kernel configuration
to enable this feature.

Reviewed by: robert, sam, gnn, julian, kmacy

un-__P()

Clean up VCS Ids.

Space cleanup

Approved by: re (rwatson)

Commit the change from FAST_IPSEC to IPSEC. The FAST_IPSEC
option is now deprecated, as well as the KAME IPsec code.
What was FAST_IPSEC is now IPSEC.

Approved by: re
Sponsored by: Secure Computing

Commit IPv6 support for FAST_IPSEC to the tree.
This commit includes only the kernel files, the rest of the files
will follow in a second commit.

Reviewed by: bz
Approved by: re
Supported by: Secure Computing

- Disabled responding to NI queries from a global address by default as
specified in RFC4620. A new flag for icmp6_nodeinfo was added to enable the
feature.
- Also cleaned up the code so that the semantics of the icmp6_nodeinfo
flags is clearer (i.e., defined specific macro names instead of using
hard-coded values).

Approved by: gnn (mentor)
MFC after: 1 week

Reduce the default number of header options that the IPv6 protocol
stack will process from 50 to 15. As this is a sysctl variable it
can be tuned up or down at the user/administrator's whim.

Submitted by: itojun
MFC after: 1 day

Make IPv6 multicast forwarding dynamically loadable from a GENERIC kernel.
It is built in the same module as IPv4 multicast forwarding, i.e. ip_mroute.ko,
if and only if IPv6 support is enabled for loadable modules.
Export IPv6 forwarding structs to userland netstat(1) via sysctl(9).

Ok, here it is, we finally add SCTP to current. Note that this
work is not just mine, but it is also the works of Peter Lei
and Michael Tuexen. They both are my two key other developers
working on the project.. and they need ata-boy's too:
****
peterlei@cisco.com
tuexen@fh-muenster.de
****
I did do a make sysent which updated the
syscall's and sysproto.. I hope that is correct... without
it you don't build since we have new syscalls for SCTP :-0

So go out and look at the NOTES, add
option SCTP (make sure inet and inet6 are present too)
and play with SCTP.

I will see about comitting some test tools I have after I
figure out where I should place them. I also have a
lib (libsctp.a) that adds some of the missing socketapi
functions that I need to put into lib's.. I will talk
to George about this :-)

There may still be some 64 bit issues in here, none of
us have a 64 bit processor to test with yet.. Michael
may have a MAC but thats another beast too..

If you have a mac and want to use SCTP contact Michael
he maintains a web site with a loadable module with
this code :-)

Reviewed by: gnn
Approved by: gnn

Make net.inet6.ip6.auto_linklocal tunable. Someone may want to
enable/disable auto_linklocal even in single user mode.

Discussed with: re@, gnn@
MFC after: 3 days

With exception of the if_name() macro, all definitions in net_osdep.h
were unused or already in if_var.h so add if_name() to if_var.h and
remove net_osdep.h along with all references to it.

Longer term we may want to kill off if_name() entierly since all modern
BSDs have if_xname variables rendering it unnecessicary.

Use sparse initializers for "struct domain" and "struct protosw",
so they are easier to follow for the human being.

added a knob to enable path MTU discovery for multicast packets.
(by default, it is disabled)

Submitted by: suz
Obtained from: KAME

supports stealth forwarding in IPv6, as well as in IPv4

PR: kern/54625
MFC after: 1 week

Style nit.

scope cleanup. with this change
- most of the kernel code will not care about the actual encoding of
scope zone IDs and won't touch "s6_addr16[1]" directly.
- similarly, most of the kernel code will not care about link-local
scoped addresses as a special case.
- scope boundary check will be stricter. For example, the current
*BSD code allows a packet with src=::1 and dst=(some global IPv6
address) to be sent outside of the node, if the application do:
s = socket(AF_INET6);
bind(s, "::1");
sendto(s, some_global_IPv6_addr);
This is clearly wrong, since ::1 is only meaningful within a single
node, but the current implementation of the *BSD kernel cannot
reject this attempt.

Submitted by: JINMEI Tatuya <jinmei__at__isl.rdc.toshiba.co.jp>
Obtained from: KAME

Add CARP (Common Address Redundancy Protocol), which allows multiple
hosts to share an IP address, providing high availability and load
balancing.

Original work on CARP done by Michael Shalayeff, with many
additions by Marco Pfatschbacher and Ryan McBride.

FreeBSD port done solely by Max Laier.

Patch by: mlaier
Obtained from: OpenBSD (mickey, mcbride)

/* -> /*- for license, minor formatting changes, separate for KAME

Remove in6_prefix.[ch] and the contained router renumbering capability.
The prefix management code currently resides in nd6, leaving only the
unused router renumbering capability in the in6_prefix files. Removing
it will make it easier for us to provide locking for the remainder of
IPv6 by reducing the number of objects requiring synchronized access.

This functionality has also been removed from NetBSD and OpenBSD.

Submitted by: George Neville-Neil <gnn at neville-neil.com>
Discussed with/approved by: suz, keiichi at kame.net, core at kame.net

Get rid of the RANDOM_IP_ID option and make it a sysctl. NetBSD
have already done this, so I have styled the patch on their work:

1) introduce a ip_newid() static inline function that checks
the sysctl and then decides if it should return a sequential
or random IP ID.

2) named the sysctl net.inet.ip.random_id

3) IPv6 flow IDs and fragment IDs are now always random.
Flow IDs and frag IDs are significantly less common in the
IPv6 world (ie. rarely generated per-packet), so there should
be smaller performance concerns.

The sysctl defaults to 0 (sequential IP IDs).

Reviewed by: andre, silby, mlaier, ume
Based on: NetBSD
MFC after: 2 months

Remove advertising clause from University of California Regent's
license, per letter dated July 22, 1999 and email from Peter Wemm,
Alan Cox and Robert Watson.

Approved by: core, peter, alc, rwatson

source address selection part of RFC3484.
TODO: since there is scope issue to be solved, multicast and
link-local address are treated as special for workaround for
now.

Obtained from: KAME

- implement lock around IPv6 reassembly, to avoid panic due to
frag6_drain (mutex version will come later).
- limit number of fragments (not fragment queues) in kernel.

Obtained from: KAME

- add dom_if{attach,detach} framework.
- transition to use ifp->if_afdata.

Obtained from: KAME

- fix typo in comments.
- style.
- NULL is not 0.
- some variables were renamed.
- nuke unused logic.
(there is no functional change.)

Obtained from: KAME

return(code) -> return (code)
(reduce diffs against KAME)

randomize IPv6 flowlabel when RANDOM_IP_ID is defined.

Obtained from: KAME

- include opt_random_ip_id.h
- we don't need to obtain microtime when using ip6_randomid.

we don't need ip6_id when RANDOM_IP_ID is defined.

Tie new "Fast IPsec" code into the build. This involves the usual
configuration stuff as well as conditional code in the IPv4 and IPv6
areas. Everything is conditional on FAST_IPSEC which is mutually
exclusive with IPSEC (KAME IPsec implmentation).

As noted previously, don't use FAST_IPSEC with INET6 at the moment.

Reviewed by: KAME, rwatson
Approved by: silence
Supported by: Vernier Networks

Change the default setting of an IPv4-mapped IPv6 address to off.

Requested by: many people

just merged cosmetic changes from KAME to ease sync between KAME and FreeBSD.
(based on freebsd4-snap-20020128)

Reviewed by: ume
MFC after: 1 week

gif(4) and stf(4) modernization:

- Remove gif dependencies from stf.
- Make gif and stf into modules
- Make gif cloneable.

PR: kern/27983
Reviewed by: ru, ume
Obtained from: NetBSD
MFC after: 1 week

- create an entry of IPV6CTL_STATS sysctl.
- fix the problem that netstat doesn't show raw6 and icmp6 pcblist.
- make netstat use sysctl to retreive stats of ipv6 and icmpv6
instead of kread.

Obtained from: KAME
MFC after: 1 week

Sync with recent KAME.
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.

TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.

Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks

Make the default value of net.inet.ip.maxfragpackets and
net.inet6.ip6.maxfragpackets dependent on nmbclusters,
defaulting to nmbclusters / 4

Reviewed by: bde
MFC after: 1 week

Back out jesper's 2001/05/31 14:58:11 PDT commit. It does not compile.

Change the default value of net.inet6.ip6.maxfragpackets from
200 to NMBCLUSTERS/4 to match the IPv4 case.

MFC after: 1 week

Convert all users of fldoff() to offsetof(). fldoff() is bad
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.

Define __offsetof() in <machine/ansi.h>

Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>

Remove myriad of local offsetof() definitions.

Remove includes of <stddef.h> in kernel code.

NB: Kernelcode should *never* include from /usr/include !

Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.

Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.

Paritials reviews by: various.
Significant brucifications by: bde

sync with kame tree as of july00. tons of bug fixes/improvements.

API changes:
- additional IPv6 ioctls
- IPsec PF_KEY API was changed, it is mandatory to upgrade setkey(8).
(also syntax change)

Previous commit changing SYSCTL_HANDLER_ARGS violated KNF.

Pointed out by: bde

Style police catches up with rev 1.26 of src/sys/sys/sysctl.h:

Sanitize SYSCTL_HANDLER_ARGS so that simplistic tools can grog our
sources:

-sysctl_vm_zone SYSCTL_HANDLER_ARGS
+sysctl_vm_zone (SYSCTL_HANDLER_ARGS)

IPv6 multicast routing.
kernel IPv6 multicast routing support.
pim6 dense mode daemon
pim6 sparse mode daemon
netstat support of IPv6 multicast routing statistics

Merging to the current and testing with other existing multicast routers
is done by Tatsuya Jinmei <jinmei@kame.net>, who writes and maintainances
the base code in KAME distribution.

Make world check and kernel build check was also successful.

tcp updates to support IPv6.
also a small patch to sys/nfs/nfs_socket.c, as max_hdr size change.

Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project

IPSEC support in the kernel.
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.

Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project

udp IPv6 support, IPv6/IPv4 tunneling support in kernel,
packet divert at kernel for IPv6/IPv4 translater daemon

This includes queue related patch submitted by jburkhol@home.com.

Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project

Removed IPSEC and IPV6FIREWALL because they are not ready yet.

KAME netinet6 basic part(no IPsec,no V6 Multicast Forwarding, no UDP/TCP
for IPv6 yet)

With this patch, you can assigne IPv6 addr automatically, and can reply to
IPv6 ping.

Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project