Copy stable/10@r272459 to releng/10.1 as part of
the 10.1-RELEASE process.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

MFC 265155, 265254:

Omit from the universe build all config files tagged with #NO_UNIVERSE.

Add FDT to the VYBRID kernel.

MFC 263301

In kernel config files, it is supposed to be 'options<space><tab>' not
'options<tab><tab>', per long standing (but recently not so strictly
enforced) convention.

MFC 263245: Make all the comments '# ' and align to same column.

MFC 257774, 256760, 262916, 262905, 262918, 262919, 262920, 262921, 262924,
262925, 262929, 262932, 262935, 262940, 262941, 262942, 262948, 262949,
262950

Strip arm/conf/DEFAULTS down to just items that are mandatory for running
the architecture.

Move all the files named foo/common.c to foo/foo_common.c

Initial cut for DTS on the hl201 board.

Add commented out dts for sam9260ek as well as early printf support.

Make clock optional on uart nodes, then back it out ("I don't know what I
was thinking, but it is lame.")

Set the baud rate if it isn't 0

Make at91_soc_id() public.

Properly round at91 resource on unmapping.

Move AT91 AIC related stuff to own file.

Fix another bug in multicast filtering. i.MX uses 6 bits from MSB in
LE CRC32 for the hash value, not the lowest 6 bits in BE CRC32.

Follow r262916 with one more config file that references a renamed common.c

Remove bogus AT91 define that causes compile errors. Most of the defines
for SAM9X are going away soonish anyway (once FDT works), but until
then...

Remove all dregs of a per-thread undefined-exception-mode stack.

Rework the VFP code that handles demand-based save and restore of state.

Always call vfp_discard() on thread death.

When a thread begins life it doesn't own the VFP hardware state on any cpu.

Make undefined exception entry MP-safe.

MFC r261570, r261572

Revert r260440 (add USB_HOST_ALIGN to all configs, it's only needed for
platforms with a 64-byte cacheline size).

Add option USB_HOST_ALIGN=64 for all SoCs that have 64 byte cache lines.

MFC r261252, r261279, r261304, r261305, r261322, r261336, r261337, r261338,
r261353

Fix the name of the dts file for the HL201...

When mapping an address, the bsh needs the same offset we do for other things.

Add explicit depends on bus_if.h and device_if.h to avoid a
chicken and egg problem in some compilation environments.

Switch to using PAs rather than VAs for the addresses we map for
devices. This is a nop, except for what's reported by atmelbus for the
resources.

Comment cleanups. Move things around for diff reduction against FDT work.

MFC r261038, r261039, r261040, r261041

Implement generic support for early printf.

MFC r260695, r260696, r260884, r260885, r260886, r260887

Provide a simplified way to specify GPIO pins for the Atmel port.

Add at91 data so we can convert a PIO unit number into a base address.

Add at91 standard memory controller helper functions.

Generalize AT91 NAND support a bit.

Connect NAND for the SAM9260EK eval board, as well as the HotE HL-201.

Add nand device and NANDFS into the mix for those at91 boards that have
support for it at the moment.

MFC r260440, r260441, r260447, r260490, r260493

Add option USB_HOST_ALIGN to configs that contain 'device usb'.

Update dts files of Cubieboard1,2 to use 1GB memory.

Add a function to print the contents of the static device mapping table,

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Back out r253779 & r253786.

Decouple yarrow from random(4) device.

* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.

* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.

* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah

* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.

* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.

* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.

Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien

fix the kernel files to match our standard "option<space><tab>" format
such that when commenting/uncommentting lines, horizontal spacing is
maintained...

Also fix some minor comment formatting to line things up, etc...

Reviewed by: gnn, imp
MFC after: 1 week

Prefer ate over macb. macb doesn't work anymore, and ate has more
errata workarounds in it.

Strip trailing whitespace.

Remove pty(4) from our kernel configurations.

As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.

The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.

Fix a zyd(4) comment typo that was copy+pasted into most kernel config files.

PR: 160276
Submitted by: MATSUMIYA Ryo <matsumiya@mma.club.uec.ac.jp>
Approved by: re (kib)
MFC after: 1 week

Change all the sample kernel configurations to use
NFSCL, NFSD instead of NFSCLIENT, NFSSERVER since
NFSCL and NFSD are now the defaults. The client change is
needed for diskless configurations, so that the root
mount works for fstype nfs.
Reported by seanbru at yahoo-inc.com for i386/XEN.

Approved by: re (hrs)

Import preliminary support for Atmel AT91SAM9G20 cpu, and the Hot-e HL201.
This fine work was done by Yohanes Nugroho <yohanes a gmail dot com>
Many thanks to John Nicholls and Thinlinx for providing sample hardware.