- Copy stable/10 (r259064) to releng/10.0 as part of the
10.0-RELEASE cycle.
- Update __FreeBSD_version [1]
- Set branch name to -RC1

[1] 10.0-CURRENT __FreeBSD_version value ended at '55', so
start releng/10.0 at '100' so the branch is started with
a value ending in zero.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Nuke "systat -mbuf". It was broken since FreeBSD 5, and since there
haven't been any complaints, no one used it.

Fix whitespace inconsistencies in systat(1).

According to md5(1), the resulting binary is the same.

Remove the advertising clause from UCB copyrighted files in usr.bin. This
is in accordance with the information provided at
ftp://ftp.cs.berkeley.edu/pub/4bsd/README.Impt.License.Change

Also add $FreeBSD$ to a few files to keep svn happy.

Discussed with: imp, rwatson

Backout sensors framework.

Requested by: phk
Discussed on: cvs-all

Import OpenBSD's sysctl hardware sensors framework.

This commit includes the following core components:

* sample configuration file for sensorsd
* rc(8) script and glue code for sensorsd(8)
* sysctl(3) doc fixes for CTL_HW tree
* sysctl(3) documentation for hardware sensors
* sysctl(8) documentation for hardware sensors
* support for the sensor structure for sysctl(8)
* rc.conf(5) documentation for starting sensorsd(8)
* sensor_attach(9) et al documentation
* /sys/kern/kern_sensors.c
o sensor_attach(9) API for drivers to register ksensors
o sensor_task_register(9) API for the update task
o sysctl(3) glue code
o hw.sensors shadow tree for sysctl(8) internal magic
* <sys/sensors.h>
* HW_SENSORS definition for <sys/sysctl.h>
* sensors display for systat(1), including documentation
* sensorsd(8) and all applicable documentation

The userland part of the framework is entirely source-code
compatible with OpenBSD 4.1, 4.2 and -current as of today.

All sensor readings can be viewed with `sysctl hw.sensors`,
monitored in semi-realtime with `systat -sensors` and also
logged with `sensorsd`.

Submitted by: Constantine A. Murenin <cnst@FreeBSD.org>
Sponsored by: Google Summer of Code 2007 (GSoC2007/cnst-sensors)
Mentored by: syrinx
Tested by: many
OKed by: kensmith
Obtained from: OpenBSD (parts)

Show the load average in the tcp display (it was already shown, perhaps
not very usefully, in all other displays). This was the original point
of the PR.

Move the load average up by 2 so that it starts in row 0 for all windows
(2 lines above it were wasted for all other windows except vmstat).
Move everything below it up by 2 or 3 (3 for icmp and icmp6 which had
an extra blank line due from not compensating for the foot-shooting in
note (3); only ip and ip6 compensated). Reduce the magic numbers related
to this.

Notes by the submitter:
%%%
1. All the subwin() calls are identical using #define MAINWIN_ROW 3
(systat.h).
2. The load average is at the top of the window.
3. Each display starts on the fourth line. I made changes to those
displays that shifted the start line (i.e., icmp). This entailed a
lot of changes within the comments at the top of those displays.
4. For ip6, I shifted the "Input next-header histogram" column down one
row to separate it from "IPv6 Output". I raised "bad scope packets"
and "address selection failed" up one row to stay with "IPv6 Input"
(valid?). They were down one row to probably line up at the bottom,
but I think they should stick with their fellow items in a column.
5. I condensed ifstat a bit. It had a lot of empty rows.
%%%

Submitted by: Se=E1n Farley <sean-freebsd at farley dot org>
PR: bin/81874

Add ip6 and icmp6 displays to systat.

MFC after: 2 weeks

Add "ifstat" display:

ifstat Display the network traffic going through active interfaces
on the system. Idle interfaces will not be displayed until
they receive some traffic.

For each interface being displayed, the current, peak and
total statistics are displayed for incoming and outgoing
traffic. By default, the ifstat display will automatically
scale the units being used so that they are in a human-read-
able format. The scaling units used for the current and peak
traffic columns can be altered by the scale command.

Submitted by: Trent Nelson <trent@arpa.com>

WARNS=2 fixes with NO_WERROR set, as there are some header issues
with namelists. use __FBSDID().

Display -tcp w/o load average so that all statistics fits on a 80x25 screen.

$Id$ -> $FreeBSD$

Having done ICMP, UDP, and IP, could a TCP display be far behind?

Emboldened by the success of yesterday's ICMP statistics display,
I've now added one that does IP (and also UDP) statistics.

Add a mode to display ICMP statistics.

Inspired by: IRIX netstat -C

This commit was generated by cvs2svn to compensate for changes in r1590,
which included commits to RCS files with non-trunk default branches.

BSD 4.4 Lite Usr.bin Sources