- Copy stable/10 (r259064) to releng/10.0 as part of the
10.0-RELEASE cycle.
- Update __FreeBSD_version [1]
- Set branch name to -RC1

[1] 10.0-CURRENT __FreeBSD_version value ended at '55', so
start releng/10.0 at '100' so the branch is started with
a value ending in zero.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Replicate r242422 from ata(4) to mvs(4):
Only four specific ATA PIO commands transfer several sectors per DRQ block
(interrupt). All other ATA PIO commands transfer one sector or 512 bytes
at one time. Hardcode these exceptions in mvs(4) with ATA_CAM option.
This fixes timeout of READ LOG EXT command used by `smartctl -x /dev/adaX`.
Also it fixes timeout of DOWNLOAD_MICROCODE on `camcontrol fwdownload`.

Reform the busdma API so that new types may be added without modifying
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.

The cam changes unify the bus_dmamap_load* handling in cam drivers.

The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.

Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)

- Limit r214102 workaround to only x86. On arm it causes more problems
then solves because of cache coherency issues. This fixes periodic error
messages on console and command timeouts.
- Patch SATA PHY configuration for 65nm SoCs to improve SNR same as
Linux does.

MFC after: 2 weeks

Partially revert r236666:
Return PROTO_ATA protocol in response to XPT_PATH_INQ.

smartmontools uses it to identify ATA devices and I don't know any other
place now where it is important. It could probably use XPT_GDEV_TYPE
instead for more accurate protocol information, but let it live for now.

Reported by: matthew
MFC after: 3 days

ATA/SATA controllers have no idea about protocol of the connected device
until transport will do some probe actions (at least soft reset).
Make ATA/SATA SIMs to not report bogus and confusing PROTO_ATA protocol.
Make ATA/SATA transport to fill that gap by reporting protocol to SIM with
XPT_SET_TRAN_SETTINGS and patching XPT_GET_TRAN_SETTINGS results if needed.

Add two functions xpt_batch_start() and xpt_batch_done() to the CAM SIM KPI
to allow drivers to handle request completion directly without passing
them to the CAM SWI thread removing extra context switch.
Modify all ATA/SATA drivers to use them.

Reviewed by: gibbs, ken
MFC after: 2 weeks

Mark MALLOC_DEFINEs static that have no corresponding MALLOC_DECLAREs.

This means that their use is restricted to a single C file.

According to SATA specification, when Serial ATA Enclosure Management Bridge
(SEMB) is unable to communicate to Storage Enclosure Processor (SEP), in
response to hard and soft resets it should among other things return value
0x7F in Status register. The weird side is that it means DRQ bit set, which
tells that reset request is not completed. It would be fine if SEMB was the
only device on port. But if SEMB connected to PMP or built into it, it may
block access to other devices sharing same SATA port.

Make some tunings/fixes to soft-reset handling to workaround the issue:
- ahci(4): request CLO on the port after soft reset to ignore DRQ bit;
- siis(4): gracefully reinitialize port after soft reset timeout (hardware
doesn't detect reset request completion in this case);
- mvs(4): if PMP is used, send dummy soft-reset to the PMP port to make it
clear DRQ bit for us.

For now this makes quirks in ata_pmp.c, hiding SEMB ports of SiI3726/SiI4726
PMPs, less important. Further, if hardware permit, I hope to implement real
SEMB support.

Fix some English grammar.

According to specification. device should respond to COMRESET with COMINIT
in no more then 10ms. If we detected no device presence within that time,
there is no reason to wait longer.

Properly handle memory allocation errors during error recovery.

Refactor hard-reset implementation in mvs(4).

Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.

This fixes system freeze for 5-10 seconds on drives hot plug-in.

Improve SATA Asynchronous Notification feature support in CAM:
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.

This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.

Implement automatic SCSI sense fetching for mvs(4).

Make few improvements/changes to ATAPI PIO support to pass most of scgcheck
(cdrtools) tests.

Workaround strange situation when EDMA_RESQIP register returns zero instead
of proper value. It caused bunch of "EMPTY CRPB" messages and potentially
may cause premature requests completion, which could cause data corruption.
For most cases it seems enough to just reread register to get proper value.
To protect against worse cases - erase processed queue entries with
impossible values and ignore them if problem still happen.

Some style cleanup:
- remove commented debugging code;
- wrap long lines.

Fix panic, when due to some kind of congestion on FIS-based switching
port multiplier some command triggers false positive timeout, but then
completes normally.

MFC after: 2 weeks

Export PCI IDs of ATA/SATA controllers through CAM and ata(4) layers to
GEOM. This information needed for proper soft-RAID's on-disk metadata
reading and writing.

Plug memory leak to silent Coverity. Error is still not really handled.

Found with: Coverity Prevent(tm)
CID: 4137

Improve suspend/resume support. Make sure controller is idle on suspend
and reset it on resume.

Fix polled operation. Now it is possible to dump kernel via mvs(4).

Import mvs(4) - Marvell 88SX50XX/88SX60XX/88SX70XX/SoC SATA controllers
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.