ixgbe_common.c revision 330897
1/****************************************************************************** 2 SPDX-License-Identifier: BSD-3-Clause 3 4 Copyright (c) 2001-2017, Intel Corporation 5 All rights reserved. 6 7 Redistribution and use in source and binary forms, with or without 8 modification, are permitted provided that the following conditions are met: 9 10 1. Redistributions of source code must retain the above copyright notice, 11 this list of conditions and the following disclaimer. 12 13 2. Redistributions in binary form must reproduce the above copyright 14 notice, this list of conditions and the following disclaimer in the 15 documentation and/or other materials provided with the distribution. 16 17 3. Neither the name of the Intel Corporation nor the names of its 18 contributors may be used to endorse or promote products derived from 19 this software without specific prior written permission. 20 21 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 22 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 24 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 25 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 26 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 27 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 28 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 29 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 30 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 31 POSSIBILITY OF SUCH DAMAGE. 32 33******************************************************************************/ 34/*$FreeBSD: stable/11/sys/dev/ixgbe/ixgbe_common.c 330897 2018-03-14 03:19:51Z eadler $*/ 35 36#include "ixgbe_common.h" 37#include "ixgbe_phy.h" 38#include "ixgbe_dcb.h" 39#include "ixgbe_dcb_82599.h" 40#include "ixgbe_api.h" 41 42static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw); 43static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw); 44static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw); 45static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw); 46static void ixgbe_standby_eeprom(struct ixgbe_hw *hw); 47static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, 48 u16 count); 49static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count); 50static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); 51static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); 52static void ixgbe_release_eeprom(struct ixgbe_hw *hw); 53 54static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); 55static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw, 56 u16 *san_mac_offset); 57static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 58 u16 words, u16 *data); 59static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 60 u16 words, u16 *data); 61static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, 62 u16 offset); 63 64/** 65 * ixgbe_init_ops_generic - Inits function ptrs 66 * @hw: pointer to the hardware structure 67 * 68 * Initialize the function pointers. 69 **/ 70s32 ixgbe_init_ops_generic(struct ixgbe_hw *hw) 71{ 72 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 73 struct ixgbe_mac_info *mac = &hw->mac; 74 u32 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 75 76 DEBUGFUNC("ixgbe_init_ops_generic"); 77 78 /* EEPROM */ 79 eeprom->ops.init_params = ixgbe_init_eeprom_params_generic; 80 /* If EEPROM is valid (bit 8 = 1), use EERD otherwise use bit bang */ 81 if (eec & IXGBE_EEC_PRES) { 82 eeprom->ops.read = ixgbe_read_eerd_generic; 83 eeprom->ops.read_buffer = ixgbe_read_eerd_buffer_generic; 84 } else { 85 eeprom->ops.read = ixgbe_read_eeprom_bit_bang_generic; 86 eeprom->ops.read_buffer = 87 ixgbe_read_eeprom_buffer_bit_bang_generic; 88 } 89 eeprom->ops.write = ixgbe_write_eeprom_generic; 90 eeprom->ops.write_buffer = ixgbe_write_eeprom_buffer_bit_bang_generic; 91 eeprom->ops.validate_checksum = 92 ixgbe_validate_eeprom_checksum_generic; 93 eeprom->ops.update_checksum = ixgbe_update_eeprom_checksum_generic; 94 eeprom->ops.calc_checksum = ixgbe_calc_eeprom_checksum_generic; 95 96 /* MAC */ 97 mac->ops.init_hw = ixgbe_init_hw_generic; 98 mac->ops.reset_hw = NULL; 99 mac->ops.start_hw = ixgbe_start_hw_generic; 100 mac->ops.clear_hw_cntrs = ixgbe_clear_hw_cntrs_generic; 101 mac->ops.get_media_type = NULL; 102 mac->ops.get_supported_physical_layer = NULL; 103 mac->ops.enable_rx_dma = ixgbe_enable_rx_dma_generic; 104 mac->ops.get_mac_addr = ixgbe_get_mac_addr_generic; 105 mac->ops.stop_adapter = ixgbe_stop_adapter_generic; 106 mac->ops.get_bus_info = ixgbe_get_bus_info_generic; 107 mac->ops.set_lan_id = ixgbe_set_lan_id_multi_port_pcie; 108 mac->ops.acquire_swfw_sync = ixgbe_acquire_swfw_sync; 109 mac->ops.release_swfw_sync = ixgbe_release_swfw_sync; 110 mac->ops.prot_autoc_read = prot_autoc_read_generic; 111 mac->ops.prot_autoc_write = prot_autoc_write_generic; 112 113 /* LEDs */ 114 mac->ops.led_on = ixgbe_led_on_generic; 115 mac->ops.led_off = ixgbe_led_off_generic; 116 mac->ops.blink_led_start = ixgbe_blink_led_start_generic; 117 mac->ops.blink_led_stop = ixgbe_blink_led_stop_generic; 118 mac->ops.init_led_link_act = ixgbe_init_led_link_act_generic; 119 120 /* RAR, Multicast, VLAN */ 121 mac->ops.set_rar = ixgbe_set_rar_generic; 122 mac->ops.clear_rar = ixgbe_clear_rar_generic; 123 mac->ops.insert_mac_addr = NULL; 124 mac->ops.set_vmdq = NULL; 125 mac->ops.clear_vmdq = NULL; 126 mac->ops.init_rx_addrs = ixgbe_init_rx_addrs_generic; 127 mac->ops.update_uc_addr_list = ixgbe_update_uc_addr_list_generic; 128 mac->ops.update_mc_addr_list = ixgbe_update_mc_addr_list_generic; 129 mac->ops.enable_mc = ixgbe_enable_mc_generic; 130 mac->ops.disable_mc = ixgbe_disable_mc_generic; 131 mac->ops.clear_vfta = NULL; 132 mac->ops.set_vfta = NULL; 133 mac->ops.set_vlvf = NULL; 134 mac->ops.init_uta_tables = NULL; 135 mac->ops.enable_rx = ixgbe_enable_rx_generic; 136 mac->ops.disable_rx = ixgbe_disable_rx_generic; 137 138 /* Flow Control */ 139 mac->ops.fc_enable = ixgbe_fc_enable_generic; 140 mac->ops.setup_fc = ixgbe_setup_fc_generic; 141 mac->ops.fc_autoneg = ixgbe_fc_autoneg; 142 143 /* Link */ 144 mac->ops.get_link_capabilities = NULL; 145 mac->ops.setup_link = NULL; 146 mac->ops.check_link = NULL; 147 mac->ops.dmac_config = NULL; 148 mac->ops.dmac_update_tcs = NULL; 149 mac->ops.dmac_config_tcs = NULL; 150 151 return IXGBE_SUCCESS; 152} 153 154/** 155 * ixgbe_device_supports_autoneg_fc - Check if device supports autonegotiation 156 * of flow control 157 * @hw: pointer to hardware structure 158 * 159 * This function returns TRUE if the device supports flow control 160 * autonegotiation, and FALSE if it does not. 161 * 162 **/ 163bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) 164{ 165 bool supported = FALSE; 166 ixgbe_link_speed speed; 167 bool link_up; 168 169 DEBUGFUNC("ixgbe_device_supports_autoneg_fc"); 170 171 switch (hw->phy.media_type) { 172 case ixgbe_media_type_fiber_fixed: 173 case ixgbe_media_type_fiber_qsfp: 174 case ixgbe_media_type_fiber: 175 /* flow control autoneg black list */ 176 switch (hw->device_id) { 177 case IXGBE_DEV_ID_X550EM_A_SFP: 178 case IXGBE_DEV_ID_X550EM_A_SFP_N: 179 case IXGBE_DEV_ID_X550EM_A_QSFP: 180 case IXGBE_DEV_ID_X550EM_A_QSFP_N: 181 supported = FALSE; 182 break; 183 default: 184 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 185 /* if link is down, assume supported */ 186 if (link_up) 187 supported = speed == IXGBE_LINK_SPEED_1GB_FULL ? 188 TRUE : FALSE; 189 else 190 supported = TRUE; 191 } 192 193 break; 194 case ixgbe_media_type_backplane: 195 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI) 196 supported = FALSE; 197 else 198 supported = TRUE; 199 break; 200 case ixgbe_media_type_copper: 201 /* only some copper devices support flow control autoneg */ 202 switch (hw->device_id) { 203 case IXGBE_DEV_ID_82599_T3_LOM: 204 case IXGBE_DEV_ID_X540T: 205 case IXGBE_DEV_ID_X540T1: 206 case IXGBE_DEV_ID_X540_BYPASS: 207 case IXGBE_DEV_ID_X550T: 208 case IXGBE_DEV_ID_X550T1: 209 case IXGBE_DEV_ID_X550EM_X_10G_T: 210 case IXGBE_DEV_ID_X550EM_A_10G_T: 211 case IXGBE_DEV_ID_X550EM_A_1G_T: 212 case IXGBE_DEV_ID_X550EM_A_1G_T_L: 213 supported = TRUE; 214 break; 215 default: 216 supported = FALSE; 217 } 218 default: 219 break; 220 } 221 222 if (!supported) 223 ERROR_REPORT2(IXGBE_ERROR_UNSUPPORTED, 224 "Device %x does not support flow control autoneg", 225 hw->device_id); 226 return supported; 227} 228 229/** 230 * ixgbe_setup_fc_generic - Set up flow control 231 * @hw: pointer to hardware structure 232 * 233 * Called at init time to set up flow control. 234 **/ 235s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw) 236{ 237 s32 ret_val = IXGBE_SUCCESS; 238 u32 reg = 0, reg_bp = 0; 239 u16 reg_cu = 0; 240 bool locked = FALSE; 241 242 DEBUGFUNC("ixgbe_setup_fc_generic"); 243 244 /* Validate the requested mode */ 245 if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { 246 ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, 247 "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); 248 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 249 goto out; 250 } 251 252 /* 253 * 10gig parts do not have a word in the EEPROM to determine the 254 * default flow control setting, so we explicitly set it to full. 255 */ 256 if (hw->fc.requested_mode == ixgbe_fc_default) 257 hw->fc.requested_mode = ixgbe_fc_full; 258 259 /* 260 * Set up the 1G and 10G flow control advertisement registers so the 261 * HW will be able to do fc autoneg once the cable is plugged in. If 262 * we link at 10G, the 1G advertisement is harmless and vice versa. 263 */ 264 switch (hw->phy.media_type) { 265 case ixgbe_media_type_backplane: 266 /* some MAC's need RMW protection on AUTOC */ 267 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, ®_bp); 268 if (ret_val != IXGBE_SUCCESS) 269 goto out; 270 271 /* fall through - only backplane uses autoc */ 272 case ixgbe_media_type_fiber_fixed: 273 case ixgbe_media_type_fiber_qsfp: 274 case ixgbe_media_type_fiber: 275 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); 276 277 break; 278 case ixgbe_media_type_copper: 279 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 280 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®_cu); 281 break; 282 default: 283 break; 284 } 285 286 /* 287 * The possible values of fc.requested_mode are: 288 * 0: Flow control is completely disabled 289 * 1: Rx flow control is enabled (we can receive pause frames, 290 * but not send pause frames). 291 * 2: Tx flow control is enabled (we can send pause frames but 292 * we do not support receiving pause frames). 293 * 3: Both Rx and Tx flow control (symmetric) are enabled. 294 * other: Invalid. 295 */ 296 switch (hw->fc.requested_mode) { 297 case ixgbe_fc_none: 298 /* Flow control completely disabled by software override. */ 299 reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); 300 if (hw->phy.media_type == ixgbe_media_type_backplane) 301 reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | 302 IXGBE_AUTOC_ASM_PAUSE); 303 else if (hw->phy.media_type == ixgbe_media_type_copper) 304 reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); 305 break; 306 case ixgbe_fc_tx_pause: 307 /* 308 * Tx Flow control is enabled, and Rx Flow control is 309 * disabled by software override. 310 */ 311 reg |= IXGBE_PCS1GANA_ASM_PAUSE; 312 reg &= ~IXGBE_PCS1GANA_SYM_PAUSE; 313 if (hw->phy.media_type == ixgbe_media_type_backplane) { 314 reg_bp |= IXGBE_AUTOC_ASM_PAUSE; 315 reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE; 316 } else if (hw->phy.media_type == ixgbe_media_type_copper) { 317 reg_cu |= IXGBE_TAF_ASM_PAUSE; 318 reg_cu &= ~IXGBE_TAF_SYM_PAUSE; 319 } 320 break; 321 case ixgbe_fc_rx_pause: 322 /* 323 * Rx Flow control is enabled and Tx Flow control is 324 * disabled by software override. Since there really 325 * isn't a way to advertise that we are capable of RX 326 * Pause ONLY, we will advertise that we support both 327 * symmetric and asymmetric Rx PAUSE, as such we fall 328 * through to the fc_full statement. Later, we will 329 * disable the adapter's ability to send PAUSE frames. 330 */ 331 case ixgbe_fc_full: 332 /* Flow control (both Rx and Tx) is enabled by SW override. */ 333 reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE; 334 if (hw->phy.media_type == ixgbe_media_type_backplane) 335 reg_bp |= IXGBE_AUTOC_SYM_PAUSE | 336 IXGBE_AUTOC_ASM_PAUSE; 337 else if (hw->phy.media_type == ixgbe_media_type_copper) 338 reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE; 339 break; 340 default: 341 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, 342 "Flow control param set incorrectly\n"); 343 ret_val = IXGBE_ERR_CONFIG; 344 goto out; 345 break; 346 } 347 348 if (hw->mac.type < ixgbe_mac_X540) { 349 /* 350 * Enable auto-negotiation between the MAC & PHY; 351 * the MAC will advertise clause 37 flow control. 352 */ 353 IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); 354 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); 355 356 /* Disable AN timeout */ 357 if (hw->fc.strict_ieee) 358 reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; 359 360 IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); 361 DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg); 362 } 363 364 /* 365 * AUTOC restart handles negotiation of 1G and 10G on backplane 366 * and copper. There is no need to set the PCS1GCTL register. 367 * 368 */ 369 if (hw->phy.media_type == ixgbe_media_type_backplane) { 370 reg_bp |= IXGBE_AUTOC_AN_RESTART; 371 ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked); 372 if (ret_val) 373 goto out; 374 } else if ((hw->phy.media_type == ixgbe_media_type_copper) && 375 (ixgbe_device_supports_autoneg_fc(hw))) { 376 hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 377 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg_cu); 378 } 379 380 DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg); 381out: 382 return ret_val; 383} 384 385/** 386 * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx 387 * @hw: pointer to hardware structure 388 * 389 * Starts the hardware by filling the bus info structure and media type, clears 390 * all on chip counters, initializes receive address registers, multicast 391 * table, VLAN filter table, calls routine to set up link and flow control 392 * settings, and leaves transmit and receive units disabled and uninitialized 393 **/ 394s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) 395{ 396 s32 ret_val; 397 u32 ctrl_ext; 398 u16 device_caps; 399 400 DEBUGFUNC("ixgbe_start_hw_generic"); 401 402 /* Set the media type */ 403 hw->phy.media_type = hw->mac.ops.get_media_type(hw); 404 405 /* PHY ops initialization must be done in reset_hw() */ 406 407 /* Clear the VLAN filter table */ 408 hw->mac.ops.clear_vfta(hw); 409 410 /* Clear statistics registers */ 411 hw->mac.ops.clear_hw_cntrs(hw); 412 413 /* Set No Snoop Disable */ 414 ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT); 415 ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS; 416 IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); 417 IXGBE_WRITE_FLUSH(hw); 418 419 /* Setup flow control */ 420 ret_val = ixgbe_setup_fc(hw); 421 if (ret_val != IXGBE_SUCCESS && ret_val != IXGBE_NOT_IMPLEMENTED) { 422 DEBUGOUT1("Flow control setup failed, returning %d\n", ret_val); 423 return ret_val; 424 } 425 426 /* Cache bit indicating need for crosstalk fix */ 427 switch (hw->mac.type) { 428 case ixgbe_mac_82599EB: 429 case ixgbe_mac_X550EM_x: 430 case ixgbe_mac_X550EM_a: 431 hw->mac.ops.get_device_caps(hw, &device_caps); 432 if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR) 433 hw->need_crosstalk_fix = FALSE; 434 else 435 hw->need_crosstalk_fix = TRUE; 436 break; 437 default: 438 hw->need_crosstalk_fix = FALSE; 439 break; 440 } 441 442 /* Clear adapter stopped flag */ 443 hw->adapter_stopped = FALSE; 444 445 return IXGBE_SUCCESS; 446} 447 448/** 449 * ixgbe_start_hw_gen2 - Init sequence for common device family 450 * @hw: pointer to hw structure 451 * 452 * Performs the init sequence common to the second generation 453 * of 10 GbE devices. 454 * Devices in the second generation: 455 * 82599 456 * X540 457 **/ 458s32 ixgbe_start_hw_gen2(struct ixgbe_hw *hw) 459{ 460 u32 i; 461 u32 regval; 462 463 /* Clear the rate limiters */ 464 for (i = 0; i < hw->mac.max_tx_queues; i++) { 465 IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i); 466 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0); 467 } 468 IXGBE_WRITE_FLUSH(hw); 469 470 /* Disable relaxed ordering */ 471 for (i = 0; i < hw->mac.max_tx_queues; i++) { 472 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(i)); 473 regval &= ~IXGBE_DCA_TXCTRL_DESC_WRO_EN; 474 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(i), regval); 475 } 476 477 for (i = 0; i < hw->mac.max_rx_queues; i++) { 478 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 479 regval &= ~(IXGBE_DCA_RXCTRL_DATA_WRO_EN | 480 IXGBE_DCA_RXCTRL_HEAD_WRO_EN); 481 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 482 } 483 484 return IXGBE_SUCCESS; 485} 486 487/** 488 * ixgbe_init_hw_generic - Generic hardware initialization 489 * @hw: pointer to hardware structure 490 * 491 * Initialize the hardware by resetting the hardware, filling the bus info 492 * structure and media type, clears all on chip counters, initializes receive 493 * address registers, multicast table, VLAN filter table, calls routine to set 494 * up link and flow control settings, and leaves transmit and receive units 495 * disabled and uninitialized 496 **/ 497s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) 498{ 499 s32 status; 500 501 DEBUGFUNC("ixgbe_init_hw_generic"); 502 503 /* Reset the hardware */ 504 status = hw->mac.ops.reset_hw(hw); 505 506 if (status == IXGBE_SUCCESS || status == IXGBE_ERR_SFP_NOT_PRESENT) { 507 /* Start the HW */ 508 status = hw->mac.ops.start_hw(hw); 509 } 510 511 /* Initialize the LED link active for LED blink support */ 512 if (hw->mac.ops.init_led_link_act) 513 hw->mac.ops.init_led_link_act(hw); 514 515 if (status != IXGBE_SUCCESS) 516 DEBUGOUT1("Failed to initialize HW, STATUS = %d\n", status); 517 518 return status; 519} 520 521/** 522 * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters 523 * @hw: pointer to hardware structure 524 * 525 * Clears all hardware statistics counters by reading them from the hardware 526 * Statistics counters are clear on read. 527 **/ 528s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) 529{ 530 u16 i = 0; 531 532 DEBUGFUNC("ixgbe_clear_hw_cntrs_generic"); 533 534 IXGBE_READ_REG(hw, IXGBE_CRCERRS); 535 IXGBE_READ_REG(hw, IXGBE_ILLERRC); 536 IXGBE_READ_REG(hw, IXGBE_ERRBC); 537 IXGBE_READ_REG(hw, IXGBE_MSPDC); 538 for (i = 0; i < 8; i++) 539 IXGBE_READ_REG(hw, IXGBE_MPC(i)); 540 541 IXGBE_READ_REG(hw, IXGBE_MLFC); 542 IXGBE_READ_REG(hw, IXGBE_MRFC); 543 IXGBE_READ_REG(hw, IXGBE_RLEC); 544 IXGBE_READ_REG(hw, IXGBE_LXONTXC); 545 IXGBE_READ_REG(hw, IXGBE_LXOFFTXC); 546 if (hw->mac.type >= ixgbe_mac_82599EB) { 547 IXGBE_READ_REG(hw, IXGBE_LXONRXCNT); 548 IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT); 549 } else { 550 IXGBE_READ_REG(hw, IXGBE_LXONRXC); 551 IXGBE_READ_REG(hw, IXGBE_LXOFFRXC); 552 } 553 554 for (i = 0; i < 8; i++) { 555 IXGBE_READ_REG(hw, IXGBE_PXONTXC(i)); 556 IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i)); 557 if (hw->mac.type >= ixgbe_mac_82599EB) { 558 IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i)); 559 IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i)); 560 } else { 561 IXGBE_READ_REG(hw, IXGBE_PXONRXC(i)); 562 IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i)); 563 } 564 } 565 if (hw->mac.type >= ixgbe_mac_82599EB) 566 for (i = 0; i < 8; i++) 567 IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i)); 568 IXGBE_READ_REG(hw, IXGBE_PRC64); 569 IXGBE_READ_REG(hw, IXGBE_PRC127); 570 IXGBE_READ_REG(hw, IXGBE_PRC255); 571 IXGBE_READ_REG(hw, IXGBE_PRC511); 572 IXGBE_READ_REG(hw, IXGBE_PRC1023); 573 IXGBE_READ_REG(hw, IXGBE_PRC1522); 574 IXGBE_READ_REG(hw, IXGBE_GPRC); 575 IXGBE_READ_REG(hw, IXGBE_BPRC); 576 IXGBE_READ_REG(hw, IXGBE_MPRC); 577 IXGBE_READ_REG(hw, IXGBE_GPTC); 578 IXGBE_READ_REG(hw, IXGBE_GORCL); 579 IXGBE_READ_REG(hw, IXGBE_GORCH); 580 IXGBE_READ_REG(hw, IXGBE_GOTCL); 581 IXGBE_READ_REG(hw, IXGBE_GOTCH); 582 if (hw->mac.type == ixgbe_mac_82598EB) 583 for (i = 0; i < 8; i++) 584 IXGBE_READ_REG(hw, IXGBE_RNBC(i)); 585 IXGBE_READ_REG(hw, IXGBE_RUC); 586 IXGBE_READ_REG(hw, IXGBE_RFC); 587 IXGBE_READ_REG(hw, IXGBE_ROC); 588 IXGBE_READ_REG(hw, IXGBE_RJC); 589 IXGBE_READ_REG(hw, IXGBE_MNGPRC); 590 IXGBE_READ_REG(hw, IXGBE_MNGPDC); 591 IXGBE_READ_REG(hw, IXGBE_MNGPTC); 592 IXGBE_READ_REG(hw, IXGBE_TORL); 593 IXGBE_READ_REG(hw, IXGBE_TORH); 594 IXGBE_READ_REG(hw, IXGBE_TPR); 595 IXGBE_READ_REG(hw, IXGBE_TPT); 596 IXGBE_READ_REG(hw, IXGBE_PTC64); 597 IXGBE_READ_REG(hw, IXGBE_PTC127); 598 IXGBE_READ_REG(hw, IXGBE_PTC255); 599 IXGBE_READ_REG(hw, IXGBE_PTC511); 600 IXGBE_READ_REG(hw, IXGBE_PTC1023); 601 IXGBE_READ_REG(hw, IXGBE_PTC1522); 602 IXGBE_READ_REG(hw, IXGBE_MPTC); 603 IXGBE_READ_REG(hw, IXGBE_BPTC); 604 for (i = 0; i < 16; i++) { 605 IXGBE_READ_REG(hw, IXGBE_QPRC(i)); 606 IXGBE_READ_REG(hw, IXGBE_QPTC(i)); 607 if (hw->mac.type >= ixgbe_mac_82599EB) { 608 IXGBE_READ_REG(hw, IXGBE_QBRC_L(i)); 609 IXGBE_READ_REG(hw, IXGBE_QBRC_H(i)); 610 IXGBE_READ_REG(hw, IXGBE_QBTC_L(i)); 611 IXGBE_READ_REG(hw, IXGBE_QBTC_H(i)); 612 IXGBE_READ_REG(hw, IXGBE_QPRDC(i)); 613 } else { 614 IXGBE_READ_REG(hw, IXGBE_QBRC(i)); 615 IXGBE_READ_REG(hw, IXGBE_QBTC(i)); 616 } 617 } 618 619 if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) { 620 if (hw->phy.id == 0) 621 ixgbe_identify_phy(hw); 622 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, 623 IXGBE_MDIO_PCS_DEV_TYPE, &i); 624 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, 625 IXGBE_MDIO_PCS_DEV_TYPE, &i); 626 hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, 627 IXGBE_MDIO_PCS_DEV_TYPE, &i); 628 hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, 629 IXGBE_MDIO_PCS_DEV_TYPE, &i); 630 } 631 632 return IXGBE_SUCCESS; 633} 634 635/** 636 * ixgbe_read_pba_string_generic - Reads part number string from EEPROM 637 * @hw: pointer to hardware structure 638 * @pba_num: stores the part number string from the EEPROM 639 * @pba_num_size: part number string buffer length 640 * 641 * Reads the part number string from the EEPROM. 642 **/ 643s32 ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num, 644 u32 pba_num_size) 645{ 646 s32 ret_val; 647 u16 data; 648 u16 pba_ptr; 649 u16 offset; 650 u16 length; 651 652 DEBUGFUNC("ixgbe_read_pba_string_generic"); 653 654 if (pba_num == NULL) { 655 DEBUGOUT("PBA string buffer was null\n"); 656 return IXGBE_ERR_INVALID_ARGUMENT; 657 } 658 659 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); 660 if (ret_val) { 661 DEBUGOUT("NVM Read Error\n"); 662 return ret_val; 663 } 664 665 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr); 666 if (ret_val) { 667 DEBUGOUT("NVM Read Error\n"); 668 return ret_val; 669 } 670 671 /* 672 * if data is not ptr guard the PBA must be in legacy format which 673 * means pba_ptr is actually our second data word for the PBA number 674 * and we can decode it into an ascii string 675 */ 676 if (data != IXGBE_PBANUM_PTR_GUARD) { 677 DEBUGOUT("NVM PBA number is not stored as string\n"); 678 679 /* we will need 11 characters to store the PBA */ 680 if (pba_num_size < 11) { 681 DEBUGOUT("PBA string buffer too small\n"); 682 return IXGBE_ERR_NO_SPACE; 683 } 684 685 /* extract hex string from data and pba_ptr */ 686 pba_num[0] = (data >> 12) & 0xF; 687 pba_num[1] = (data >> 8) & 0xF; 688 pba_num[2] = (data >> 4) & 0xF; 689 pba_num[3] = data & 0xF; 690 pba_num[4] = (pba_ptr >> 12) & 0xF; 691 pba_num[5] = (pba_ptr >> 8) & 0xF; 692 pba_num[6] = '-'; 693 pba_num[7] = 0; 694 pba_num[8] = (pba_ptr >> 4) & 0xF; 695 pba_num[9] = pba_ptr & 0xF; 696 697 /* put a null character on the end of our string */ 698 pba_num[10] = '\0'; 699 700 /* switch all the data but the '-' to hex char */ 701 for (offset = 0; offset < 10; offset++) { 702 if (pba_num[offset] < 0xA) 703 pba_num[offset] += '0'; 704 else if (pba_num[offset] < 0x10) 705 pba_num[offset] += 'A' - 0xA; 706 } 707 708 return IXGBE_SUCCESS; 709 } 710 711 ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length); 712 if (ret_val) { 713 DEBUGOUT("NVM Read Error\n"); 714 return ret_val; 715 } 716 717 if (length == 0xFFFF || length == 0) { 718 DEBUGOUT("NVM PBA number section invalid length\n"); 719 return IXGBE_ERR_PBA_SECTION; 720 } 721 722 /* check if pba_num buffer is big enough */ 723 if (pba_num_size < (((u32)length * 2) - 1)) { 724 DEBUGOUT("PBA string buffer too small\n"); 725 return IXGBE_ERR_NO_SPACE; 726 } 727 728 /* trim pba length from start of string */ 729 pba_ptr++; 730 length--; 731 732 for (offset = 0; offset < length; offset++) { 733 ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data); 734 if (ret_val) { 735 DEBUGOUT("NVM Read Error\n"); 736 return ret_val; 737 } 738 pba_num[offset * 2] = (u8)(data >> 8); 739 pba_num[(offset * 2) + 1] = (u8)(data & 0xFF); 740 } 741 pba_num[offset * 2] = '\0'; 742 743 return IXGBE_SUCCESS; 744} 745 746/** 747 * ixgbe_read_pba_num_generic - Reads part number from EEPROM 748 * @hw: pointer to hardware structure 749 * @pba_num: stores the part number from the EEPROM 750 * 751 * Reads the part number from the EEPROM. 752 **/ 753s32 ixgbe_read_pba_num_generic(struct ixgbe_hw *hw, u32 *pba_num) 754{ 755 s32 ret_val; 756 u16 data; 757 758 DEBUGFUNC("ixgbe_read_pba_num_generic"); 759 760 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); 761 if (ret_val) { 762 DEBUGOUT("NVM Read Error\n"); 763 return ret_val; 764 } else if (data == IXGBE_PBANUM_PTR_GUARD) { 765 DEBUGOUT("NVM Not supported\n"); 766 return IXGBE_NOT_IMPLEMENTED; 767 } 768 *pba_num = (u32)(data << 16); 769 770 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &data); 771 if (ret_val) { 772 DEBUGOUT("NVM Read Error\n"); 773 return ret_val; 774 } 775 *pba_num |= data; 776 777 return IXGBE_SUCCESS; 778} 779 780/** 781 * ixgbe_read_pba_raw 782 * @hw: pointer to the HW structure 783 * @eeprom_buf: optional pointer to EEPROM image 784 * @eeprom_buf_size: size of EEPROM image in words 785 * @max_pba_block_size: PBA block size limit 786 * @pba: pointer to output PBA structure 787 * 788 * Reads PBA from EEPROM image when eeprom_buf is not NULL. 789 * Reads PBA from physical EEPROM device when eeprom_buf is NULL. 790 * 791 **/ 792s32 ixgbe_read_pba_raw(struct ixgbe_hw *hw, u16 *eeprom_buf, 793 u32 eeprom_buf_size, u16 max_pba_block_size, 794 struct ixgbe_pba *pba) 795{ 796 s32 ret_val; 797 u16 pba_block_size; 798 799 if (pba == NULL) 800 return IXGBE_ERR_PARAM; 801 802 if (eeprom_buf == NULL) { 803 ret_val = hw->eeprom.ops.read_buffer(hw, IXGBE_PBANUM0_PTR, 2, 804 &pba->word[0]); 805 if (ret_val) 806 return ret_val; 807 } else { 808 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 809 pba->word[0] = eeprom_buf[IXGBE_PBANUM0_PTR]; 810 pba->word[1] = eeprom_buf[IXGBE_PBANUM1_PTR]; 811 } else { 812 return IXGBE_ERR_PARAM; 813 } 814 } 815 816 if (pba->word[0] == IXGBE_PBANUM_PTR_GUARD) { 817 if (pba->pba_block == NULL) 818 return IXGBE_ERR_PARAM; 819 820 ret_val = ixgbe_get_pba_block_size(hw, eeprom_buf, 821 eeprom_buf_size, 822 &pba_block_size); 823 if (ret_val) 824 return ret_val; 825 826 if (pba_block_size > max_pba_block_size) 827 return IXGBE_ERR_PARAM; 828 829 if (eeprom_buf == NULL) { 830 ret_val = hw->eeprom.ops.read_buffer(hw, pba->word[1], 831 pba_block_size, 832 pba->pba_block); 833 if (ret_val) 834 return ret_val; 835 } else { 836 if (eeprom_buf_size > (u32)(pba->word[1] + 837 pba_block_size)) { 838 memcpy(pba->pba_block, 839 &eeprom_buf[pba->word[1]], 840 pba_block_size * sizeof(u16)); 841 } else { 842 return IXGBE_ERR_PARAM; 843 } 844 } 845 } 846 847 return IXGBE_SUCCESS; 848} 849 850/** 851 * ixgbe_write_pba_raw 852 * @hw: pointer to the HW structure 853 * @eeprom_buf: optional pointer to EEPROM image 854 * @eeprom_buf_size: size of EEPROM image in words 855 * @pba: pointer to PBA structure 856 * 857 * Writes PBA to EEPROM image when eeprom_buf is not NULL. 858 * Writes PBA to physical EEPROM device when eeprom_buf is NULL. 859 * 860 **/ 861s32 ixgbe_write_pba_raw(struct ixgbe_hw *hw, u16 *eeprom_buf, 862 u32 eeprom_buf_size, struct ixgbe_pba *pba) 863{ 864 s32 ret_val; 865 866 if (pba == NULL) 867 return IXGBE_ERR_PARAM; 868 869 if (eeprom_buf == NULL) { 870 ret_val = hw->eeprom.ops.write_buffer(hw, IXGBE_PBANUM0_PTR, 2, 871 &pba->word[0]); 872 if (ret_val) 873 return ret_val; 874 } else { 875 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 876 eeprom_buf[IXGBE_PBANUM0_PTR] = pba->word[0]; 877 eeprom_buf[IXGBE_PBANUM1_PTR] = pba->word[1]; 878 } else { 879 return IXGBE_ERR_PARAM; 880 } 881 } 882 883 if (pba->word[0] == IXGBE_PBANUM_PTR_GUARD) { 884 if (pba->pba_block == NULL) 885 return IXGBE_ERR_PARAM; 886 887 if (eeprom_buf == NULL) { 888 ret_val = hw->eeprom.ops.write_buffer(hw, pba->word[1], 889 pba->pba_block[0], 890 pba->pba_block); 891 if (ret_val) 892 return ret_val; 893 } else { 894 if (eeprom_buf_size > (u32)(pba->word[1] + 895 pba->pba_block[0])) { 896 memcpy(&eeprom_buf[pba->word[1]], 897 pba->pba_block, 898 pba->pba_block[0] * sizeof(u16)); 899 } else { 900 return IXGBE_ERR_PARAM; 901 } 902 } 903 } 904 905 return IXGBE_SUCCESS; 906} 907 908/** 909 * ixgbe_get_pba_block_size 910 * @hw: pointer to the HW structure 911 * @eeprom_buf: optional pointer to EEPROM image 912 * @eeprom_buf_size: size of EEPROM image in words 913 * @pba_data_size: pointer to output variable 914 * 915 * Returns the size of the PBA block in words. Function operates on EEPROM 916 * image if the eeprom_buf pointer is not NULL otherwise it accesses physical 917 * EEPROM device. 918 * 919 **/ 920s32 ixgbe_get_pba_block_size(struct ixgbe_hw *hw, u16 *eeprom_buf, 921 u32 eeprom_buf_size, u16 *pba_block_size) 922{ 923 s32 ret_val; 924 u16 pba_word[2]; 925 u16 length; 926 927 DEBUGFUNC("ixgbe_get_pba_block_size"); 928 929 if (eeprom_buf == NULL) { 930 ret_val = hw->eeprom.ops.read_buffer(hw, IXGBE_PBANUM0_PTR, 2, 931 &pba_word[0]); 932 if (ret_val) 933 return ret_val; 934 } else { 935 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 936 pba_word[0] = eeprom_buf[IXGBE_PBANUM0_PTR]; 937 pba_word[1] = eeprom_buf[IXGBE_PBANUM1_PTR]; 938 } else { 939 return IXGBE_ERR_PARAM; 940 } 941 } 942 943 if (pba_word[0] == IXGBE_PBANUM_PTR_GUARD) { 944 if (eeprom_buf == NULL) { 945 ret_val = hw->eeprom.ops.read(hw, pba_word[1] + 0, 946 &length); 947 if (ret_val) 948 return ret_val; 949 } else { 950 if (eeprom_buf_size > pba_word[1]) 951 length = eeprom_buf[pba_word[1] + 0]; 952 else 953 return IXGBE_ERR_PARAM; 954 } 955 956 if (length == 0xFFFF || length == 0) 957 return IXGBE_ERR_PBA_SECTION; 958 } else { 959 /* PBA number in legacy format, there is no PBA Block. */ 960 length = 0; 961 } 962 963 if (pba_block_size != NULL) 964 *pba_block_size = length; 965 966 return IXGBE_SUCCESS; 967} 968 969/** 970 * ixgbe_get_mac_addr_generic - Generic get MAC address 971 * @hw: pointer to hardware structure 972 * @mac_addr: Adapter MAC address 973 * 974 * Reads the adapter's MAC address from first Receive Address Register (RAR0) 975 * A reset of the adapter must be performed prior to calling this function 976 * in order for the MAC address to have been loaded from the EEPROM into RAR0 977 **/ 978s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr) 979{ 980 u32 rar_high; 981 u32 rar_low; 982 u16 i; 983 984 DEBUGFUNC("ixgbe_get_mac_addr_generic"); 985 986 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0)); 987 rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0)); 988 989 for (i = 0; i < 4; i++) 990 mac_addr[i] = (u8)(rar_low >> (i*8)); 991 992 for (i = 0; i < 2; i++) 993 mac_addr[i+4] = (u8)(rar_high >> (i*8)); 994 995 return IXGBE_SUCCESS; 996} 997 998/** 999 * ixgbe_set_pci_config_data_generic - Generic store PCI bus info 1000 * @hw: pointer to hardware structure 1001 * @link_status: the link status returned by the PCI config space 1002 * 1003 * Stores the PCI bus info (speed, width, type) within the ixgbe_hw structure 1004 **/ 1005void ixgbe_set_pci_config_data_generic(struct ixgbe_hw *hw, u16 link_status) 1006{ 1007 struct ixgbe_mac_info *mac = &hw->mac; 1008 1009 if (hw->bus.type == ixgbe_bus_type_unknown) 1010 hw->bus.type = ixgbe_bus_type_pci_express; 1011 1012 switch (link_status & IXGBE_PCI_LINK_WIDTH) { 1013 case IXGBE_PCI_LINK_WIDTH_1: 1014 hw->bus.width = ixgbe_bus_width_pcie_x1; 1015 break; 1016 case IXGBE_PCI_LINK_WIDTH_2: 1017 hw->bus.width = ixgbe_bus_width_pcie_x2; 1018 break; 1019 case IXGBE_PCI_LINK_WIDTH_4: 1020 hw->bus.width = ixgbe_bus_width_pcie_x4; 1021 break; 1022 case IXGBE_PCI_LINK_WIDTH_8: 1023 hw->bus.width = ixgbe_bus_width_pcie_x8; 1024 break; 1025 default: 1026 hw->bus.width = ixgbe_bus_width_unknown; 1027 break; 1028 } 1029 1030 switch (link_status & IXGBE_PCI_LINK_SPEED) { 1031 case IXGBE_PCI_LINK_SPEED_2500: 1032 hw->bus.speed = ixgbe_bus_speed_2500; 1033 break; 1034 case IXGBE_PCI_LINK_SPEED_5000: 1035 hw->bus.speed = ixgbe_bus_speed_5000; 1036 break; 1037 case IXGBE_PCI_LINK_SPEED_8000: 1038 hw->bus.speed = ixgbe_bus_speed_8000; 1039 break; 1040 default: 1041 hw->bus.speed = ixgbe_bus_speed_unknown; 1042 break; 1043 } 1044 1045 mac->ops.set_lan_id(hw); 1046} 1047 1048/** 1049 * ixgbe_get_bus_info_generic - Generic set PCI bus info 1050 * @hw: pointer to hardware structure 1051 * 1052 * Gets the PCI bus info (speed, width, type) then calls helper function to 1053 * store this data within the ixgbe_hw structure. 1054 **/ 1055s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw) 1056{ 1057 u16 link_status; 1058 1059 DEBUGFUNC("ixgbe_get_bus_info_generic"); 1060 1061 /* Get the negotiated link width and speed from PCI config space */ 1062 link_status = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_LINK_STATUS); 1063 1064 ixgbe_set_pci_config_data_generic(hw, link_status); 1065 1066 return IXGBE_SUCCESS; 1067} 1068 1069/** 1070 * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices 1071 * @hw: pointer to the HW structure 1072 * 1073 * Determines the LAN function id by reading memory-mapped registers and swaps 1074 * the port value if requested, and set MAC instance for devices that share 1075 * CS4227. 1076 **/ 1077void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw) 1078{ 1079 struct ixgbe_bus_info *bus = &hw->bus; 1080 u32 reg; 1081 u16 ee_ctrl_4; 1082 1083 DEBUGFUNC("ixgbe_set_lan_id_multi_port_pcie"); 1084 1085 reg = IXGBE_READ_REG(hw, IXGBE_STATUS); 1086 bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT; 1087 bus->lan_id = (u8)bus->func; 1088 1089 /* check for a port swap */ 1090 reg = IXGBE_READ_REG(hw, IXGBE_FACTPS_BY_MAC(hw)); 1091 if (reg & IXGBE_FACTPS_LFS) 1092 bus->func ^= 0x1; 1093 1094 /* Get MAC instance from EEPROM for configuring CS4227 */ 1095 if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) { 1096 hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4); 1097 bus->instance_id = (ee_ctrl_4 & IXGBE_EE_CTRL_4_INST_ID) >> 1098 IXGBE_EE_CTRL_4_INST_ID_SHIFT; 1099 } 1100} 1101 1102/** 1103 * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units 1104 * @hw: pointer to hardware structure 1105 * 1106 * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts, 1107 * disables transmit and receive units. The adapter_stopped flag is used by 1108 * the shared code and drivers to determine if the adapter is in a stopped 1109 * state and should not touch the hardware. 1110 **/ 1111s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) 1112{ 1113 u32 reg_val; 1114 u16 i; 1115 1116 DEBUGFUNC("ixgbe_stop_adapter_generic"); 1117 1118 /* 1119 * Set the adapter_stopped flag so other driver functions stop touching 1120 * the hardware 1121 */ 1122 hw->adapter_stopped = TRUE; 1123 1124 /* Disable the receive unit */ 1125 ixgbe_disable_rx(hw); 1126 1127 /* Clear interrupt mask to stop interrupts from being generated */ 1128 IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK); 1129 1130 /* Clear any pending interrupts, flush previous writes */ 1131 IXGBE_READ_REG(hw, IXGBE_EICR); 1132 1133 /* Disable the transmit unit. Each queue must be disabled. */ 1134 for (i = 0; i < hw->mac.max_tx_queues; i++) 1135 IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH); 1136 1137 /* Disable the receive unit by stopping each queue */ 1138 for (i = 0; i < hw->mac.max_rx_queues; i++) { 1139 reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i)); 1140 reg_val &= ~IXGBE_RXDCTL_ENABLE; 1141 reg_val |= IXGBE_RXDCTL_SWFLSH; 1142 IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val); 1143 } 1144 1145 /* flush all queues disables */ 1146 IXGBE_WRITE_FLUSH(hw); 1147 msec_delay(2); 1148 1149 /* 1150 * Prevent the PCI-E bus from hanging by disabling PCI-E master 1151 * access and verify no pending requests 1152 */ 1153 return ixgbe_disable_pcie_master(hw); 1154} 1155 1156/** 1157 * ixgbe_init_led_link_act_generic - Store the LED index link/activity. 1158 * @hw: pointer to hardware structure 1159 * 1160 * Store the index for the link active LED. This will be used to support 1161 * blinking the LED. 1162 **/ 1163s32 ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw) 1164{ 1165 struct ixgbe_mac_info *mac = &hw->mac; 1166 u32 led_reg, led_mode; 1167 u8 i; 1168 1169 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 1170 1171 /* Get LED link active from the LEDCTL register */ 1172 for (i = 0; i < 4; i++) { 1173 led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i); 1174 1175 if ((led_mode & IXGBE_LED_MODE_MASK_BASE) == 1176 IXGBE_LED_LINK_ACTIVE) { 1177 mac->led_link_act = i; 1178 return IXGBE_SUCCESS; 1179 } 1180 } 1181 1182 /* 1183 * If LEDCTL register does not have the LED link active set, then use 1184 * known MAC defaults. 1185 */ 1186 switch (hw->mac.type) { 1187 case ixgbe_mac_X550EM_a: 1188 case ixgbe_mac_X550EM_x: 1189 mac->led_link_act = 1; 1190 break; 1191 default: 1192 mac->led_link_act = 2; 1193 } 1194 return IXGBE_SUCCESS; 1195} 1196 1197/** 1198 * ixgbe_led_on_generic - Turns on the software controllable LEDs. 1199 * @hw: pointer to hardware structure 1200 * @index: led number to turn on 1201 **/ 1202s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index) 1203{ 1204 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 1205 1206 DEBUGFUNC("ixgbe_led_on_generic"); 1207 1208 if (index > 3) 1209 return IXGBE_ERR_PARAM; 1210 1211 /* To turn on the LED, set mode to ON. */ 1212 led_reg &= ~IXGBE_LED_MODE_MASK(index); 1213 led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index); 1214 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 1215 IXGBE_WRITE_FLUSH(hw); 1216 1217 return IXGBE_SUCCESS; 1218} 1219 1220/** 1221 * ixgbe_led_off_generic - Turns off the software controllable LEDs. 1222 * @hw: pointer to hardware structure 1223 * @index: led number to turn off 1224 **/ 1225s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index) 1226{ 1227 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 1228 1229 DEBUGFUNC("ixgbe_led_off_generic"); 1230 1231 if (index > 3) 1232 return IXGBE_ERR_PARAM; 1233 1234 /* To turn off the LED, set mode to OFF. */ 1235 led_reg &= ~IXGBE_LED_MODE_MASK(index); 1236 led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index); 1237 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 1238 IXGBE_WRITE_FLUSH(hw); 1239 1240 return IXGBE_SUCCESS; 1241} 1242 1243/** 1244 * ixgbe_init_eeprom_params_generic - Initialize EEPROM params 1245 * @hw: pointer to hardware structure 1246 * 1247 * Initializes the EEPROM parameters ixgbe_eeprom_info within the 1248 * ixgbe_hw struct in order to set up EEPROM access. 1249 **/ 1250s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) 1251{ 1252 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 1253 u32 eec; 1254 u16 eeprom_size; 1255 1256 DEBUGFUNC("ixgbe_init_eeprom_params_generic"); 1257 1258 if (eeprom->type == ixgbe_eeprom_uninitialized) { 1259 eeprom->type = ixgbe_eeprom_none; 1260 /* Set default semaphore delay to 10ms which is a well 1261 * tested value */ 1262 eeprom->semaphore_delay = 10; 1263 /* Clear EEPROM page size, it will be initialized as needed */ 1264 eeprom->word_page_size = 0; 1265 1266 /* 1267 * Check for EEPROM present first. 1268 * If not present leave as none 1269 */ 1270 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 1271 if (eec & IXGBE_EEC_PRES) { 1272 eeprom->type = ixgbe_eeprom_spi; 1273 1274 /* 1275 * SPI EEPROM is assumed here. This code would need to 1276 * change if a future EEPROM is not SPI. 1277 */ 1278 eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >> 1279 IXGBE_EEC_SIZE_SHIFT); 1280 eeprom->word_size = 1 << (eeprom_size + 1281 IXGBE_EEPROM_WORD_SIZE_SHIFT); 1282 } 1283 1284 if (eec & IXGBE_EEC_ADDR_SIZE) 1285 eeprom->address_bits = 16; 1286 else 1287 eeprom->address_bits = 8; 1288 DEBUGOUT3("Eeprom params: type = %d, size = %d, address bits: " 1289 "%d\n", eeprom->type, eeprom->word_size, 1290 eeprom->address_bits); 1291 } 1292 1293 return IXGBE_SUCCESS; 1294} 1295 1296/** 1297 * ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang 1298 * @hw: pointer to hardware structure 1299 * @offset: offset within the EEPROM to write 1300 * @words: number of word(s) 1301 * @data: 16 bit word(s) to write to EEPROM 1302 * 1303 * Reads 16 bit word(s) from EEPROM through bit-bang method 1304 **/ 1305s32 ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1306 u16 words, u16 *data) 1307{ 1308 s32 status = IXGBE_SUCCESS; 1309 u16 i, count; 1310 1311 DEBUGFUNC("ixgbe_write_eeprom_buffer_bit_bang_generic"); 1312 1313 hw->eeprom.ops.init_params(hw); 1314 1315 if (words == 0) { 1316 status = IXGBE_ERR_INVALID_ARGUMENT; 1317 goto out; 1318 } 1319 1320 if (offset + words > hw->eeprom.word_size) { 1321 status = IXGBE_ERR_EEPROM; 1322 goto out; 1323 } 1324 1325 /* 1326 * The EEPROM page size cannot be queried from the chip. We do lazy 1327 * initialization. It is worth to do that when we write large buffer. 1328 */ 1329 if ((hw->eeprom.word_page_size == 0) && 1330 (words > IXGBE_EEPROM_PAGE_SIZE_MAX)) 1331 ixgbe_detect_eeprom_page_size_generic(hw, offset); 1332 1333 /* 1334 * We cannot hold synchronization semaphores for too long 1335 * to avoid other entity starvation. However it is more efficient 1336 * to read in bursts than synchronizing access for each word. 1337 */ 1338 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { 1339 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? 1340 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); 1341 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i, 1342 count, &data[i]); 1343 1344 if (status != IXGBE_SUCCESS) 1345 break; 1346 } 1347 1348out: 1349 return status; 1350} 1351 1352/** 1353 * ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM 1354 * @hw: pointer to hardware structure 1355 * @offset: offset within the EEPROM to be written to 1356 * @words: number of word(s) 1357 * @data: 16 bit word(s) to be written to the EEPROM 1358 * 1359 * If ixgbe_eeprom_update_checksum is not called after this function, the 1360 * EEPROM will most likely contain an invalid checksum. 1361 **/ 1362static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 1363 u16 words, u16 *data) 1364{ 1365 s32 status; 1366 u16 word; 1367 u16 page_size; 1368 u16 i; 1369 u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI; 1370 1371 DEBUGFUNC("ixgbe_write_eeprom_buffer_bit_bang"); 1372 1373 /* Prepare the EEPROM for writing */ 1374 status = ixgbe_acquire_eeprom(hw); 1375 1376 if (status == IXGBE_SUCCESS) { 1377 if (ixgbe_ready_eeprom(hw) != IXGBE_SUCCESS) { 1378 ixgbe_release_eeprom(hw); 1379 status = IXGBE_ERR_EEPROM; 1380 } 1381 } 1382 1383 if (status == IXGBE_SUCCESS) { 1384 for (i = 0; i < words; i++) { 1385 ixgbe_standby_eeprom(hw); 1386 1387 /* Send the WRITE ENABLE command (8 bit opcode ) */ 1388 ixgbe_shift_out_eeprom_bits(hw, 1389 IXGBE_EEPROM_WREN_OPCODE_SPI, 1390 IXGBE_EEPROM_OPCODE_BITS); 1391 1392 ixgbe_standby_eeprom(hw); 1393 1394 /* 1395 * Some SPI eeproms use the 8th address bit embedded 1396 * in the opcode 1397 */ 1398 if ((hw->eeprom.address_bits == 8) && 1399 ((offset + i) >= 128)) 1400 write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; 1401 1402 /* Send the Write command (8-bit opcode + addr) */ 1403 ixgbe_shift_out_eeprom_bits(hw, write_opcode, 1404 IXGBE_EEPROM_OPCODE_BITS); 1405 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), 1406 hw->eeprom.address_bits); 1407 1408 page_size = hw->eeprom.word_page_size; 1409 1410 /* Send the data in burst via SPI*/ 1411 do { 1412 word = data[i]; 1413 word = (word >> 8) | (word << 8); 1414 ixgbe_shift_out_eeprom_bits(hw, word, 16); 1415 1416 if (page_size == 0) 1417 break; 1418 1419 /* do not wrap around page */ 1420 if (((offset + i) & (page_size - 1)) == 1421 (page_size - 1)) 1422 break; 1423 } while (++i < words); 1424 1425 ixgbe_standby_eeprom(hw); 1426 msec_delay(10); 1427 } 1428 /* Done with writing - release the EEPROM */ 1429 ixgbe_release_eeprom(hw); 1430 } 1431 1432 return status; 1433} 1434 1435/** 1436 * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM 1437 * @hw: pointer to hardware structure 1438 * @offset: offset within the EEPROM to be written to 1439 * @data: 16 bit word to be written to the EEPROM 1440 * 1441 * If ixgbe_eeprom_update_checksum is not called after this function, the 1442 * EEPROM will most likely contain an invalid checksum. 1443 **/ 1444s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data) 1445{ 1446 s32 status; 1447 1448 DEBUGFUNC("ixgbe_write_eeprom_generic"); 1449 1450 hw->eeprom.ops.init_params(hw); 1451 1452 if (offset >= hw->eeprom.word_size) { 1453 status = IXGBE_ERR_EEPROM; 1454 goto out; 1455 } 1456 1457 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data); 1458 1459out: 1460 return status; 1461} 1462 1463/** 1464 * ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang 1465 * @hw: pointer to hardware structure 1466 * @offset: offset within the EEPROM to be read 1467 * @data: read 16 bit words(s) from EEPROM 1468 * @words: number of word(s) 1469 * 1470 * Reads 16 bit word(s) from EEPROM through bit-bang method 1471 **/ 1472s32 ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1473 u16 words, u16 *data) 1474{ 1475 s32 status = IXGBE_SUCCESS; 1476 u16 i, count; 1477 1478 DEBUGFUNC("ixgbe_read_eeprom_buffer_bit_bang_generic"); 1479 1480 hw->eeprom.ops.init_params(hw); 1481 1482 if (words == 0) { 1483 status = IXGBE_ERR_INVALID_ARGUMENT; 1484 goto out; 1485 } 1486 1487 if (offset + words > hw->eeprom.word_size) { 1488 status = IXGBE_ERR_EEPROM; 1489 goto out; 1490 } 1491 1492 /* 1493 * We cannot hold synchronization semaphores for too long 1494 * to avoid other entity starvation. However it is more efficient 1495 * to read in bursts than synchronizing access for each word. 1496 */ 1497 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { 1498 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? 1499 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); 1500 1501 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i, 1502 count, &data[i]); 1503 1504 if (status != IXGBE_SUCCESS) 1505 break; 1506 } 1507 1508out: 1509 return status; 1510} 1511 1512/** 1513 * ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang 1514 * @hw: pointer to hardware structure 1515 * @offset: offset within the EEPROM to be read 1516 * @words: number of word(s) 1517 * @data: read 16 bit word(s) from EEPROM 1518 * 1519 * Reads 16 bit word(s) from EEPROM through bit-bang method 1520 **/ 1521static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 1522 u16 words, u16 *data) 1523{ 1524 s32 status; 1525 u16 word_in; 1526 u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI; 1527 u16 i; 1528 1529 DEBUGFUNC("ixgbe_read_eeprom_buffer_bit_bang"); 1530 1531 /* Prepare the EEPROM for reading */ 1532 status = ixgbe_acquire_eeprom(hw); 1533 1534 if (status == IXGBE_SUCCESS) { 1535 if (ixgbe_ready_eeprom(hw) != IXGBE_SUCCESS) { 1536 ixgbe_release_eeprom(hw); 1537 status = IXGBE_ERR_EEPROM; 1538 } 1539 } 1540 1541 if (status == IXGBE_SUCCESS) { 1542 for (i = 0; i < words; i++) { 1543 ixgbe_standby_eeprom(hw); 1544 /* 1545 * Some SPI eeproms use the 8th address bit embedded 1546 * in the opcode 1547 */ 1548 if ((hw->eeprom.address_bits == 8) && 1549 ((offset + i) >= 128)) 1550 read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; 1551 1552 /* Send the READ command (opcode + addr) */ 1553 ixgbe_shift_out_eeprom_bits(hw, read_opcode, 1554 IXGBE_EEPROM_OPCODE_BITS); 1555 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), 1556 hw->eeprom.address_bits); 1557 1558 /* Read the data. */ 1559 word_in = ixgbe_shift_in_eeprom_bits(hw, 16); 1560 data[i] = (word_in >> 8) | (word_in << 8); 1561 } 1562 1563 /* End this read operation */ 1564 ixgbe_release_eeprom(hw); 1565 } 1566 1567 return status; 1568} 1569 1570/** 1571 * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang 1572 * @hw: pointer to hardware structure 1573 * @offset: offset within the EEPROM to be read 1574 * @data: read 16 bit value from EEPROM 1575 * 1576 * Reads 16 bit value from EEPROM through bit-bang method 1577 **/ 1578s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1579 u16 *data) 1580{ 1581 s32 status; 1582 1583 DEBUGFUNC("ixgbe_read_eeprom_bit_bang_generic"); 1584 1585 hw->eeprom.ops.init_params(hw); 1586 1587 if (offset >= hw->eeprom.word_size) { 1588 status = IXGBE_ERR_EEPROM; 1589 goto out; 1590 } 1591 1592 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); 1593 1594out: 1595 return status; 1596} 1597 1598/** 1599 * ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD 1600 * @hw: pointer to hardware structure 1601 * @offset: offset of word in the EEPROM to read 1602 * @words: number of word(s) 1603 * @data: 16 bit word(s) from the EEPROM 1604 * 1605 * Reads a 16 bit word(s) from the EEPROM using the EERD register. 1606 **/ 1607s32 ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset, 1608 u16 words, u16 *data) 1609{ 1610 u32 eerd; 1611 s32 status = IXGBE_SUCCESS; 1612 u32 i; 1613 1614 DEBUGFUNC("ixgbe_read_eerd_buffer_generic"); 1615 1616 hw->eeprom.ops.init_params(hw); 1617 1618 if (words == 0) { 1619 status = IXGBE_ERR_INVALID_ARGUMENT; 1620 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM words"); 1621 goto out; 1622 } 1623 1624 if (offset >= hw->eeprom.word_size) { 1625 status = IXGBE_ERR_EEPROM; 1626 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM offset"); 1627 goto out; 1628 } 1629 1630 for (i = 0; i < words; i++) { 1631 eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | 1632 IXGBE_EEPROM_RW_REG_START; 1633 1634 IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd); 1635 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ); 1636 1637 if (status == IXGBE_SUCCESS) { 1638 data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >> 1639 IXGBE_EEPROM_RW_REG_DATA); 1640 } else { 1641 DEBUGOUT("Eeprom read timed out\n"); 1642 goto out; 1643 } 1644 } 1645out: 1646 return status; 1647} 1648 1649/** 1650 * ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size 1651 * @hw: pointer to hardware structure 1652 * @offset: offset within the EEPROM to be used as a scratch pad 1653 * 1654 * Discover EEPROM page size by writing marching data at given offset. 1655 * This function is called only when we are writing a new large buffer 1656 * at given offset so the data would be overwritten anyway. 1657 **/ 1658static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, 1659 u16 offset) 1660{ 1661 u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX]; 1662 s32 status = IXGBE_SUCCESS; 1663 u16 i; 1664 1665 DEBUGFUNC("ixgbe_detect_eeprom_page_size_generic"); 1666 1667 for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++) 1668 data[i] = i; 1669 1670 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX; 1671 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1672 IXGBE_EEPROM_PAGE_SIZE_MAX, data); 1673 hw->eeprom.word_page_size = 0; 1674 if (status != IXGBE_SUCCESS) 1675 goto out; 1676 1677 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); 1678 if (status != IXGBE_SUCCESS) 1679 goto out; 1680 1681 /* 1682 * When writing in burst more than the actual page size 1683 * EEPROM address wraps around current page. 1684 */ 1685 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0]; 1686 1687 DEBUGOUT1("Detected EEPROM page size = %d words.", 1688 hw->eeprom.word_page_size); 1689out: 1690 return status; 1691} 1692 1693/** 1694 * ixgbe_read_eerd_generic - Read EEPROM word using EERD 1695 * @hw: pointer to hardware structure 1696 * @offset: offset of word in the EEPROM to read 1697 * @data: word read from the EEPROM 1698 * 1699 * Reads a 16 bit word from the EEPROM using the EERD register. 1700 **/ 1701s32 ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data) 1702{ 1703 return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data); 1704} 1705 1706/** 1707 * ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR 1708 * @hw: pointer to hardware structure 1709 * @offset: offset of word in the EEPROM to write 1710 * @words: number of word(s) 1711 * @data: word(s) write to the EEPROM 1712 * 1713 * Write a 16 bit word(s) to the EEPROM using the EEWR register. 1714 **/ 1715s32 ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset, 1716 u16 words, u16 *data) 1717{ 1718 u32 eewr; 1719 s32 status = IXGBE_SUCCESS; 1720 u16 i; 1721 1722 DEBUGFUNC("ixgbe_write_eewr_generic"); 1723 1724 hw->eeprom.ops.init_params(hw); 1725 1726 if (words == 0) { 1727 status = IXGBE_ERR_INVALID_ARGUMENT; 1728 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM words"); 1729 goto out; 1730 } 1731 1732 if (offset >= hw->eeprom.word_size) { 1733 status = IXGBE_ERR_EEPROM; 1734 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM offset"); 1735 goto out; 1736 } 1737 1738 for (i = 0; i < words; i++) { 1739 eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | 1740 (data[i] << IXGBE_EEPROM_RW_REG_DATA) | 1741 IXGBE_EEPROM_RW_REG_START; 1742 1743 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); 1744 if (status != IXGBE_SUCCESS) { 1745 DEBUGOUT("Eeprom write EEWR timed out\n"); 1746 goto out; 1747 } 1748 1749 IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr); 1750 1751 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); 1752 if (status != IXGBE_SUCCESS) { 1753 DEBUGOUT("Eeprom write EEWR timed out\n"); 1754 goto out; 1755 } 1756 } 1757 1758out: 1759 return status; 1760} 1761 1762/** 1763 * ixgbe_write_eewr_generic - Write EEPROM word using EEWR 1764 * @hw: pointer to hardware structure 1765 * @offset: offset of word in the EEPROM to write 1766 * @data: word write to the EEPROM 1767 * 1768 * Write a 16 bit word to the EEPROM using the EEWR register. 1769 **/ 1770s32 ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data) 1771{ 1772 return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data); 1773} 1774 1775/** 1776 * ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status 1777 * @hw: pointer to hardware structure 1778 * @ee_reg: EEPROM flag for polling 1779 * 1780 * Polls the status bit (bit 1) of the EERD or EEWR to determine when the 1781 * read or write is done respectively. 1782 **/ 1783s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg) 1784{ 1785 u32 i; 1786 u32 reg; 1787 s32 status = IXGBE_ERR_EEPROM; 1788 1789 DEBUGFUNC("ixgbe_poll_eerd_eewr_done"); 1790 1791 for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) { 1792 if (ee_reg == IXGBE_NVM_POLL_READ) 1793 reg = IXGBE_READ_REG(hw, IXGBE_EERD); 1794 else 1795 reg = IXGBE_READ_REG(hw, IXGBE_EEWR); 1796 1797 if (reg & IXGBE_EEPROM_RW_REG_DONE) { 1798 status = IXGBE_SUCCESS; 1799 break; 1800 } 1801 usec_delay(5); 1802 } 1803 1804 if (i == IXGBE_EERD_EEWR_ATTEMPTS) 1805 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1806 "EEPROM read/write done polling timed out"); 1807 1808 return status; 1809} 1810 1811/** 1812 * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang 1813 * @hw: pointer to hardware structure 1814 * 1815 * Prepares EEPROM for access using bit-bang method. This function should 1816 * be called before issuing a command to the EEPROM. 1817 **/ 1818static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) 1819{ 1820 s32 status = IXGBE_SUCCESS; 1821 u32 eec; 1822 u32 i; 1823 1824 DEBUGFUNC("ixgbe_acquire_eeprom"); 1825 1826 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) 1827 != IXGBE_SUCCESS) 1828 status = IXGBE_ERR_SWFW_SYNC; 1829 1830 if (status == IXGBE_SUCCESS) { 1831 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 1832 1833 /* Request EEPROM Access */ 1834 eec |= IXGBE_EEC_REQ; 1835 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 1836 1837 for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { 1838 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 1839 if (eec & IXGBE_EEC_GNT) 1840 break; 1841 usec_delay(5); 1842 } 1843 1844 /* Release if grant not acquired */ 1845 if (!(eec & IXGBE_EEC_GNT)) { 1846 eec &= ~IXGBE_EEC_REQ; 1847 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 1848 DEBUGOUT("Could not acquire EEPROM grant\n"); 1849 1850 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 1851 status = IXGBE_ERR_EEPROM; 1852 } 1853 1854 /* Setup EEPROM for Read/Write */ 1855 if (status == IXGBE_SUCCESS) { 1856 /* Clear CS and SK */ 1857 eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); 1858 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 1859 IXGBE_WRITE_FLUSH(hw); 1860 usec_delay(1); 1861 } 1862 } 1863 return status; 1864} 1865 1866/** 1867 * ixgbe_get_eeprom_semaphore - Get hardware semaphore 1868 * @hw: pointer to hardware structure 1869 * 1870 * Sets the hardware semaphores so EEPROM access can occur for bit-bang method 1871 **/ 1872static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) 1873{ 1874 s32 status = IXGBE_ERR_EEPROM; 1875 u32 timeout = 2000; 1876 u32 i; 1877 u32 swsm; 1878 1879 DEBUGFUNC("ixgbe_get_eeprom_semaphore"); 1880 1881 1882 /* Get SMBI software semaphore between device drivers first */ 1883 for (i = 0; i < timeout; i++) { 1884 /* 1885 * If the SMBI bit is 0 when we read it, then the bit will be 1886 * set and we have the semaphore 1887 */ 1888 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM_BY_MAC(hw)); 1889 if (!(swsm & IXGBE_SWSM_SMBI)) { 1890 status = IXGBE_SUCCESS; 1891 break; 1892 } 1893 usec_delay(50); 1894 } 1895 1896 if (i == timeout) { 1897 DEBUGOUT("Driver can't access the Eeprom - SMBI Semaphore " 1898 "not granted.\n"); 1899 /* 1900 * this release is particularly important because our attempts 1901 * above to get the semaphore may have succeeded, and if there 1902 * was a timeout, we should unconditionally clear the semaphore 1903 * bits to free the driver to make progress 1904 */ 1905 ixgbe_release_eeprom_semaphore(hw); 1906 1907 usec_delay(50); 1908 /* 1909 * one last try 1910 * If the SMBI bit is 0 when we read it, then the bit will be 1911 * set and we have the semaphore 1912 */ 1913 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM_BY_MAC(hw)); 1914 if (!(swsm & IXGBE_SWSM_SMBI)) 1915 status = IXGBE_SUCCESS; 1916 } 1917 1918 /* Now get the semaphore between SW/FW through the SWESMBI bit */ 1919 if (status == IXGBE_SUCCESS) { 1920 for (i = 0; i < timeout; i++) { 1921 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM_BY_MAC(hw)); 1922 1923 /* Set the SW EEPROM semaphore bit to request access */ 1924 swsm |= IXGBE_SWSM_SWESMBI; 1925 IXGBE_WRITE_REG(hw, IXGBE_SWSM_BY_MAC(hw), swsm); 1926 1927 /* 1928 * If we set the bit successfully then we got the 1929 * semaphore. 1930 */ 1931 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM_BY_MAC(hw)); 1932 if (swsm & IXGBE_SWSM_SWESMBI) 1933 break; 1934 1935 usec_delay(50); 1936 } 1937 1938 /* 1939 * Release semaphores and return error if SW EEPROM semaphore 1940 * was not granted because we don't have access to the EEPROM 1941 */ 1942 if (i >= timeout) { 1943 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1944 "SWESMBI Software EEPROM semaphore not granted.\n"); 1945 ixgbe_release_eeprom_semaphore(hw); 1946 status = IXGBE_ERR_EEPROM; 1947 } 1948 } else { 1949 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1950 "Software semaphore SMBI between device drivers " 1951 "not granted.\n"); 1952 } 1953 1954 return status; 1955} 1956 1957/** 1958 * ixgbe_release_eeprom_semaphore - Release hardware semaphore 1959 * @hw: pointer to hardware structure 1960 * 1961 * This function clears hardware semaphore bits. 1962 **/ 1963static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) 1964{ 1965 u32 swsm; 1966 1967 DEBUGFUNC("ixgbe_release_eeprom_semaphore"); 1968 1969 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1970 1971 /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */ 1972 swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI); 1973 IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); 1974 IXGBE_WRITE_FLUSH(hw); 1975} 1976 1977/** 1978 * ixgbe_ready_eeprom - Polls for EEPROM ready 1979 * @hw: pointer to hardware structure 1980 **/ 1981static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw) 1982{ 1983 s32 status = IXGBE_SUCCESS; 1984 u16 i; 1985 u8 spi_stat_reg; 1986 1987 DEBUGFUNC("ixgbe_ready_eeprom"); 1988 1989 /* 1990 * Read "Status Register" repeatedly until the LSB is cleared. The 1991 * EEPROM will signal that the command has been completed by clearing 1992 * bit 0 of the internal status register. If it's not cleared within 1993 * 5 milliseconds, then error out. 1994 */ 1995 for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) { 1996 ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI, 1997 IXGBE_EEPROM_OPCODE_BITS); 1998 spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8); 1999 if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI)) 2000 break; 2001 2002 usec_delay(5); 2003 ixgbe_standby_eeprom(hw); 2004 }; 2005 2006 /* 2007 * On some parts, SPI write time could vary from 0-20mSec on 3.3V 2008 * devices (and only 0-5mSec on 5V devices) 2009 */ 2010 if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) { 2011 DEBUGOUT("SPI EEPROM Status error\n"); 2012 status = IXGBE_ERR_EEPROM; 2013 } 2014 2015 return status; 2016} 2017 2018/** 2019 * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state 2020 * @hw: pointer to hardware structure 2021 **/ 2022static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) 2023{ 2024 u32 eec; 2025 2026 DEBUGFUNC("ixgbe_standby_eeprom"); 2027 2028 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 2029 2030 /* Toggle CS to flush commands */ 2031 eec |= IXGBE_EEC_CS; 2032 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2033 IXGBE_WRITE_FLUSH(hw); 2034 usec_delay(1); 2035 eec &= ~IXGBE_EEC_CS; 2036 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2037 IXGBE_WRITE_FLUSH(hw); 2038 usec_delay(1); 2039} 2040 2041/** 2042 * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM. 2043 * @hw: pointer to hardware structure 2044 * @data: data to send to the EEPROM 2045 * @count: number of bits to shift out 2046 **/ 2047static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, 2048 u16 count) 2049{ 2050 u32 eec; 2051 u32 mask; 2052 u32 i; 2053 2054 DEBUGFUNC("ixgbe_shift_out_eeprom_bits"); 2055 2056 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 2057 2058 /* 2059 * Mask is used to shift "count" bits of "data" out to the EEPROM 2060 * one bit at a time. Determine the starting bit based on count 2061 */ 2062 mask = 0x01 << (count - 1); 2063 2064 for (i = 0; i < count; i++) { 2065 /* 2066 * A "1" is shifted out to the EEPROM by setting bit "DI" to a 2067 * "1", and then raising and then lowering the clock (the SK 2068 * bit controls the clock input to the EEPROM). A "0" is 2069 * shifted out to the EEPROM by setting "DI" to "0" and then 2070 * raising and then lowering the clock. 2071 */ 2072 if (data & mask) 2073 eec |= IXGBE_EEC_DI; 2074 else 2075 eec &= ~IXGBE_EEC_DI; 2076 2077 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2078 IXGBE_WRITE_FLUSH(hw); 2079 2080 usec_delay(1); 2081 2082 ixgbe_raise_eeprom_clk(hw, &eec); 2083 ixgbe_lower_eeprom_clk(hw, &eec); 2084 2085 /* 2086 * Shift mask to signify next bit of data to shift in to the 2087 * EEPROM 2088 */ 2089 mask = mask >> 1; 2090 }; 2091 2092 /* We leave the "DI" bit set to "0" when we leave this routine. */ 2093 eec &= ~IXGBE_EEC_DI; 2094 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2095 IXGBE_WRITE_FLUSH(hw); 2096} 2097 2098/** 2099 * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM 2100 * @hw: pointer to hardware structure 2101 **/ 2102static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) 2103{ 2104 u32 eec; 2105 u32 i; 2106 u16 data = 0; 2107 2108 DEBUGFUNC("ixgbe_shift_in_eeprom_bits"); 2109 2110 /* 2111 * In order to read a register from the EEPROM, we need to shift 2112 * 'count' bits in from the EEPROM. Bits are "shifted in" by raising 2113 * the clock input to the EEPROM (setting the SK bit), and then reading 2114 * the value of the "DO" bit. During this "shifting in" process the 2115 * "DI" bit should always be clear. 2116 */ 2117 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 2118 2119 eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); 2120 2121 for (i = 0; i < count; i++) { 2122 data = data << 1; 2123 ixgbe_raise_eeprom_clk(hw, &eec); 2124 2125 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 2126 2127 eec &= ~(IXGBE_EEC_DI); 2128 if (eec & IXGBE_EEC_DO) 2129 data |= 1; 2130 2131 ixgbe_lower_eeprom_clk(hw, &eec); 2132 } 2133 2134 return data; 2135} 2136 2137/** 2138 * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input. 2139 * @hw: pointer to hardware structure 2140 * @eec: EEC register's current value 2141 **/ 2142static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) 2143{ 2144 DEBUGFUNC("ixgbe_raise_eeprom_clk"); 2145 2146 /* 2147 * Raise the clock input to the EEPROM 2148 * (setting the SK bit), then delay 2149 */ 2150 *eec = *eec | IXGBE_EEC_SK; 2151 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), *eec); 2152 IXGBE_WRITE_FLUSH(hw); 2153 usec_delay(1); 2154} 2155 2156/** 2157 * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input. 2158 * @hw: pointer to hardware structure 2159 * @eecd: EECD's current value 2160 **/ 2161static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) 2162{ 2163 DEBUGFUNC("ixgbe_lower_eeprom_clk"); 2164 2165 /* 2166 * Lower the clock input to the EEPROM (clearing the SK bit), then 2167 * delay 2168 */ 2169 *eec = *eec & ~IXGBE_EEC_SK; 2170 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), *eec); 2171 IXGBE_WRITE_FLUSH(hw); 2172 usec_delay(1); 2173} 2174 2175/** 2176 * ixgbe_release_eeprom - Release EEPROM, release semaphores 2177 * @hw: pointer to hardware structure 2178 **/ 2179static void ixgbe_release_eeprom(struct ixgbe_hw *hw) 2180{ 2181 u32 eec; 2182 2183 DEBUGFUNC("ixgbe_release_eeprom"); 2184 2185 eec = IXGBE_READ_REG(hw, IXGBE_EEC_BY_MAC(hw)); 2186 2187 eec |= IXGBE_EEC_CS; /* Pull CS high */ 2188 eec &= ~IXGBE_EEC_SK; /* Lower SCK */ 2189 2190 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2191 IXGBE_WRITE_FLUSH(hw); 2192 2193 usec_delay(1); 2194 2195 /* Stop requesting EEPROM access */ 2196 eec &= ~IXGBE_EEC_REQ; 2197 IXGBE_WRITE_REG(hw, IXGBE_EEC_BY_MAC(hw), eec); 2198 2199 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2200 2201 /* Delay before attempt to obtain semaphore again to allow FW access */ 2202 msec_delay(hw->eeprom.semaphore_delay); 2203} 2204 2205/** 2206 * ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum 2207 * @hw: pointer to hardware structure 2208 * 2209 * Returns a negative error code on error, or the 16-bit checksum 2210 **/ 2211s32 ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw) 2212{ 2213 u16 i; 2214 u16 j; 2215 u16 checksum = 0; 2216 u16 length = 0; 2217 u16 pointer = 0; 2218 u16 word = 0; 2219 2220 DEBUGFUNC("ixgbe_calc_eeprom_checksum_generic"); 2221 2222 /* Include 0x0-0x3F in the checksum */ 2223 for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) { 2224 if (hw->eeprom.ops.read(hw, i, &word)) { 2225 DEBUGOUT("EEPROM read failed\n"); 2226 return IXGBE_ERR_EEPROM; 2227 } 2228 checksum += word; 2229 } 2230 2231 /* Include all data from pointers except for the fw pointer */ 2232 for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) { 2233 if (hw->eeprom.ops.read(hw, i, &pointer)) { 2234 DEBUGOUT("EEPROM read failed\n"); 2235 return IXGBE_ERR_EEPROM; 2236 } 2237 2238 /* If the pointer seems invalid */ 2239 if (pointer == 0xFFFF || pointer == 0) 2240 continue; 2241 2242 if (hw->eeprom.ops.read(hw, pointer, &length)) { 2243 DEBUGOUT("EEPROM read failed\n"); 2244 return IXGBE_ERR_EEPROM; 2245 } 2246 2247 if (length == 0xFFFF || length == 0) 2248 continue; 2249 2250 for (j = pointer + 1; j <= pointer + length; j++) { 2251 if (hw->eeprom.ops.read(hw, j, &word)) { 2252 DEBUGOUT("EEPROM read failed\n"); 2253 return IXGBE_ERR_EEPROM; 2254 } 2255 checksum += word; 2256 } 2257 } 2258 2259 checksum = (u16)IXGBE_EEPROM_SUM - checksum; 2260 2261 return (s32)checksum; 2262} 2263 2264/** 2265 * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum 2266 * @hw: pointer to hardware structure 2267 * @checksum_val: calculated checksum 2268 * 2269 * Performs checksum calculation and validates the EEPROM checksum. If the 2270 * caller does not need checksum_val, the value can be NULL. 2271 **/ 2272s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw, 2273 u16 *checksum_val) 2274{ 2275 s32 status; 2276 u16 checksum; 2277 u16 read_checksum = 0; 2278 2279 DEBUGFUNC("ixgbe_validate_eeprom_checksum_generic"); 2280 2281 /* Read the first word from the EEPROM. If this times out or fails, do 2282 * not continue or we could be in for a very long wait while every 2283 * EEPROM read fails 2284 */ 2285 status = hw->eeprom.ops.read(hw, 0, &checksum); 2286 if (status) { 2287 DEBUGOUT("EEPROM read failed\n"); 2288 return status; 2289 } 2290 2291 status = hw->eeprom.ops.calc_checksum(hw); 2292 if (status < 0) 2293 return status; 2294 2295 checksum = (u16)(status & 0xffff); 2296 2297 status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); 2298 if (status) { 2299 DEBUGOUT("EEPROM read failed\n"); 2300 return status; 2301 } 2302 2303 /* Verify read checksum from EEPROM is the same as 2304 * calculated checksum 2305 */ 2306 if (read_checksum != checksum) 2307 status = IXGBE_ERR_EEPROM_CHECKSUM; 2308 2309 /* If the user cares, return the calculated checksum */ 2310 if (checksum_val) 2311 *checksum_val = checksum; 2312 2313 return status; 2314} 2315 2316/** 2317 * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum 2318 * @hw: pointer to hardware structure 2319 **/ 2320s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw) 2321{ 2322 s32 status; 2323 u16 checksum; 2324 2325 DEBUGFUNC("ixgbe_update_eeprom_checksum_generic"); 2326 2327 /* Read the first word from the EEPROM. If this times out or fails, do 2328 * not continue or we could be in for a very long wait while every 2329 * EEPROM read fails 2330 */ 2331 status = hw->eeprom.ops.read(hw, 0, &checksum); 2332 if (status) { 2333 DEBUGOUT("EEPROM read failed\n"); 2334 return status; 2335 } 2336 2337 status = hw->eeprom.ops.calc_checksum(hw); 2338 if (status < 0) 2339 return status; 2340 2341 checksum = (u16)(status & 0xffff); 2342 2343 status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum); 2344 2345 return status; 2346} 2347 2348/** 2349 * ixgbe_validate_mac_addr - Validate MAC address 2350 * @mac_addr: pointer to MAC address. 2351 * 2352 * Tests a MAC address to ensure it is a valid Individual Address. 2353 **/ 2354s32 ixgbe_validate_mac_addr(u8 *mac_addr) 2355{ 2356 s32 status = IXGBE_SUCCESS; 2357 2358 DEBUGFUNC("ixgbe_validate_mac_addr"); 2359 2360 /* Make sure it is not a multicast address */ 2361 if (IXGBE_IS_MULTICAST(mac_addr)) { 2362 status = IXGBE_ERR_INVALID_MAC_ADDR; 2363 /* Not a broadcast address */ 2364 } else if (IXGBE_IS_BROADCAST(mac_addr)) { 2365 status = IXGBE_ERR_INVALID_MAC_ADDR; 2366 /* Reject the zero address */ 2367 } else if (mac_addr[0] == 0 && mac_addr[1] == 0 && mac_addr[2] == 0 && 2368 mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0) { 2369 status = IXGBE_ERR_INVALID_MAC_ADDR; 2370 } 2371 return status; 2372} 2373 2374/** 2375 * ixgbe_set_rar_generic - Set Rx address register 2376 * @hw: pointer to hardware structure 2377 * @index: Receive address register to write 2378 * @addr: Address to put into receive address register 2379 * @vmdq: VMDq "set" or "pool" index 2380 * @enable_addr: set flag that address is active 2381 * 2382 * Puts an ethernet address into a receive address register. 2383 **/ 2384s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, 2385 u32 enable_addr) 2386{ 2387 u32 rar_low, rar_high; 2388 u32 rar_entries = hw->mac.num_rar_entries; 2389 2390 DEBUGFUNC("ixgbe_set_rar_generic"); 2391 2392 /* Make sure we are using a valid rar index range */ 2393 if (index >= rar_entries) { 2394 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 2395 "RAR index %d is out of range.\n", index); 2396 return IXGBE_ERR_INVALID_ARGUMENT; 2397 } 2398 2399 /* setup VMDq pool selection before this RAR gets enabled */ 2400 hw->mac.ops.set_vmdq(hw, index, vmdq); 2401 2402 /* 2403 * HW expects these in little endian so we reverse the byte 2404 * order from network order (big endian) to little endian 2405 */ 2406 rar_low = ((u32)addr[0] | 2407 ((u32)addr[1] << 8) | 2408 ((u32)addr[2] << 16) | 2409 ((u32)addr[3] << 24)); 2410 /* 2411 * Some parts put the VMDq setting in the extra RAH bits, 2412 * so save everything except the lower 16 bits that hold part 2413 * of the address and the address valid bit. 2414 */ 2415 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); 2416 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); 2417 rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8)); 2418 2419 if (enable_addr != 0) 2420 rar_high |= IXGBE_RAH_AV; 2421 2422 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); 2423 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); 2424 2425 return IXGBE_SUCCESS; 2426} 2427 2428/** 2429 * ixgbe_clear_rar_generic - Remove Rx address register 2430 * @hw: pointer to hardware structure 2431 * @index: Receive address register to write 2432 * 2433 * Clears an ethernet address from a receive address register. 2434 **/ 2435s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) 2436{ 2437 u32 rar_high; 2438 u32 rar_entries = hw->mac.num_rar_entries; 2439 2440 DEBUGFUNC("ixgbe_clear_rar_generic"); 2441 2442 /* Make sure we are using a valid rar index range */ 2443 if (index >= rar_entries) { 2444 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 2445 "RAR index %d is out of range.\n", index); 2446 return IXGBE_ERR_INVALID_ARGUMENT; 2447 } 2448 2449 /* 2450 * Some parts put the VMDq setting in the extra RAH bits, 2451 * so save everything except the lower 16 bits that hold part 2452 * of the address and the address valid bit. 2453 */ 2454 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); 2455 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); 2456 2457 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); 2458 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); 2459 2460 /* clear VMDq pool/queue selection for this RAR */ 2461 hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); 2462 2463 return IXGBE_SUCCESS; 2464} 2465 2466/** 2467 * ixgbe_init_rx_addrs_generic - Initializes receive address filters. 2468 * @hw: pointer to hardware structure 2469 * 2470 * Places the MAC address in receive address register 0 and clears the rest 2471 * of the receive address registers. Clears the multicast table. Assumes 2472 * the receiver is in reset when the routine is called. 2473 **/ 2474s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw) 2475{ 2476 u32 i; 2477 u32 rar_entries = hw->mac.num_rar_entries; 2478 2479 DEBUGFUNC("ixgbe_init_rx_addrs_generic"); 2480 2481 /* 2482 * If the current mac address is valid, assume it is a software override 2483 * to the permanent address. 2484 * Otherwise, use the permanent address from the eeprom. 2485 */ 2486 if (ixgbe_validate_mac_addr(hw->mac.addr) == 2487 IXGBE_ERR_INVALID_MAC_ADDR) { 2488 /* Get the MAC address from the RAR0 for later reference */ 2489 hw->mac.ops.get_mac_addr(hw, hw->mac.addr); 2490 2491 DEBUGOUT3(" Keeping Current RAR0 Addr =%.2X %.2X %.2X ", 2492 hw->mac.addr[0], hw->mac.addr[1], 2493 hw->mac.addr[2]); 2494 DEBUGOUT3("%.2X %.2X %.2X\n", hw->mac.addr[3], 2495 hw->mac.addr[4], hw->mac.addr[5]); 2496 } else { 2497 /* Setup the receive address. */ 2498 DEBUGOUT("Overriding MAC Address in RAR[0]\n"); 2499 DEBUGOUT3(" New MAC Addr =%.2X %.2X %.2X ", 2500 hw->mac.addr[0], hw->mac.addr[1], 2501 hw->mac.addr[2]); 2502 DEBUGOUT3("%.2X %.2X %.2X\n", hw->mac.addr[3], 2503 hw->mac.addr[4], hw->mac.addr[5]); 2504 2505 hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); 2506 } 2507 2508 /* clear VMDq pool/queue selection for RAR 0 */ 2509 hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL); 2510 2511 hw->addr_ctrl.overflow_promisc = 0; 2512 2513 hw->addr_ctrl.rar_used_count = 1; 2514 2515 /* Zero out the other receive addresses. */ 2516 DEBUGOUT1("Clearing RAR[1-%d]\n", rar_entries - 1); 2517 for (i = 1; i < rar_entries; i++) { 2518 IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); 2519 IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); 2520 } 2521 2522 /* Clear the MTA */ 2523 hw->addr_ctrl.mta_in_use = 0; 2524 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); 2525 2526 DEBUGOUT(" Clearing MTA\n"); 2527 for (i = 0; i < hw->mac.mcft_size; i++) 2528 IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); 2529 2530 ixgbe_init_uta_tables(hw); 2531 2532 return IXGBE_SUCCESS; 2533} 2534 2535/** 2536 * ixgbe_add_uc_addr - Adds a secondary unicast address. 2537 * @hw: pointer to hardware structure 2538 * @addr: new address 2539 * 2540 * Adds it to unused receive address register or goes into promiscuous mode. 2541 **/ 2542void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) 2543{ 2544 u32 rar_entries = hw->mac.num_rar_entries; 2545 u32 rar; 2546 2547 DEBUGFUNC("ixgbe_add_uc_addr"); 2548 2549 DEBUGOUT6(" UC Addr = %.2X %.2X %.2X %.2X %.2X %.2X\n", 2550 addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); 2551 2552 /* 2553 * Place this address in the RAR if there is room, 2554 * else put the controller into promiscuous mode 2555 */ 2556 if (hw->addr_ctrl.rar_used_count < rar_entries) { 2557 rar = hw->addr_ctrl.rar_used_count; 2558 hw->mac.ops.set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 2559 DEBUGOUT1("Added a secondary address to RAR[%d]\n", rar); 2560 hw->addr_ctrl.rar_used_count++; 2561 } else { 2562 hw->addr_ctrl.overflow_promisc++; 2563 } 2564 2565 DEBUGOUT("ixgbe_add_uc_addr Complete\n"); 2566} 2567 2568/** 2569 * ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses 2570 * @hw: pointer to hardware structure 2571 * @addr_list: the list of new addresses 2572 * @addr_count: number of addresses 2573 * @next: iterator function to walk the address list 2574 * 2575 * The given list replaces any existing list. Clears the secondary addrs from 2576 * receive address registers. Uses unused receive address registers for the 2577 * first secondary addresses, and falls back to promiscuous mode as needed. 2578 * 2579 * Drivers using secondary unicast addresses must set user_set_promisc when 2580 * manually putting the device into promiscuous mode. 2581 **/ 2582s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list, 2583 u32 addr_count, ixgbe_mc_addr_itr next) 2584{ 2585 u8 *addr; 2586 u32 i; 2587 u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc; 2588 u32 uc_addr_in_use; 2589 u32 fctrl; 2590 u32 vmdq; 2591 2592 DEBUGFUNC("ixgbe_update_uc_addr_list_generic"); 2593 2594 /* 2595 * Clear accounting of old secondary address list, 2596 * don't count RAR[0] 2597 */ 2598 uc_addr_in_use = hw->addr_ctrl.rar_used_count - 1; 2599 hw->addr_ctrl.rar_used_count -= uc_addr_in_use; 2600 hw->addr_ctrl.overflow_promisc = 0; 2601 2602 /* Zero out the other receive addresses */ 2603 DEBUGOUT1("Clearing RAR[1-%d]\n", uc_addr_in_use+1); 2604 for (i = 0; i < uc_addr_in_use; i++) { 2605 IXGBE_WRITE_REG(hw, IXGBE_RAL(1+i), 0); 2606 IXGBE_WRITE_REG(hw, IXGBE_RAH(1+i), 0); 2607 } 2608 2609 /* Add the new addresses */ 2610 for (i = 0; i < addr_count; i++) { 2611 DEBUGOUT(" Adding the secondary addresses:\n"); 2612 addr = next(hw, &addr_list, &vmdq); 2613 ixgbe_add_uc_addr(hw, addr, vmdq); 2614 } 2615 2616 if (hw->addr_ctrl.overflow_promisc) { 2617 /* enable promisc if not already in overflow or set by user */ 2618 if (!old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { 2619 DEBUGOUT(" Entering address overflow promisc mode\n"); 2620 fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); 2621 fctrl |= IXGBE_FCTRL_UPE; 2622 IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); 2623 } 2624 } else { 2625 /* only disable if set by overflow, not by user */ 2626 if (old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { 2627 DEBUGOUT(" Leaving address overflow promisc mode\n"); 2628 fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); 2629 fctrl &= ~IXGBE_FCTRL_UPE; 2630 IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); 2631 } 2632 } 2633 2634 DEBUGOUT("ixgbe_update_uc_addr_list_generic Complete\n"); 2635 return IXGBE_SUCCESS; 2636} 2637 2638/** 2639 * ixgbe_mta_vector - Determines bit-vector in multicast table to set 2640 * @hw: pointer to hardware structure 2641 * @mc_addr: the multicast address 2642 * 2643 * Extracts the 12 bits, from a multicast address, to determine which 2644 * bit-vector to set in the multicast table. The hardware uses 12 bits, from 2645 * incoming rx multicast addresses, to determine the bit-vector to check in 2646 * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set 2647 * by the MO field of the MCSTCTRL. The MO field is set during initialization 2648 * to mc_filter_type. 2649 **/ 2650static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) 2651{ 2652 u32 vector = 0; 2653 2654 DEBUGFUNC("ixgbe_mta_vector"); 2655 2656 switch (hw->mac.mc_filter_type) { 2657 case 0: /* use bits [47:36] of the address */ 2658 vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); 2659 break; 2660 case 1: /* use bits [46:35] of the address */ 2661 vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); 2662 break; 2663 case 2: /* use bits [45:34] of the address */ 2664 vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); 2665 break; 2666 case 3: /* use bits [43:32] of the address */ 2667 vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); 2668 break; 2669 default: /* Invalid mc_filter_type */ 2670 DEBUGOUT("MC filter type param set incorrectly\n"); 2671 ASSERT(0); 2672 break; 2673 } 2674 2675 /* vector can only be 12-bits or boundary will be exceeded */ 2676 vector &= 0xFFF; 2677 return vector; 2678} 2679 2680/** 2681 * ixgbe_set_mta - Set bit-vector in multicast table 2682 * @hw: pointer to hardware structure 2683 * @hash_value: Multicast address hash value 2684 * 2685 * Sets the bit-vector in the multicast table. 2686 **/ 2687void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr) 2688{ 2689 u32 vector; 2690 u32 vector_bit; 2691 u32 vector_reg; 2692 2693 DEBUGFUNC("ixgbe_set_mta"); 2694 2695 hw->addr_ctrl.mta_in_use++; 2696 2697 vector = ixgbe_mta_vector(hw, mc_addr); 2698 DEBUGOUT1(" bit-vector = 0x%03X\n", vector); 2699 2700 /* 2701 * The MTA is a register array of 128 32-bit registers. It is treated 2702 * like an array of 4096 bits. We want to set bit 2703 * BitArray[vector_value]. So we figure out what register the bit is 2704 * in, read it, OR in the new bit, then write back the new value. The 2705 * register is determined by the upper 7 bits of the vector value and 2706 * the bit within that register are determined by the lower 5 bits of 2707 * the value. 2708 */ 2709 vector_reg = (vector >> 5) & 0x7F; 2710 vector_bit = vector & 0x1F; 2711 hw->mac.mta_shadow[vector_reg] |= (1 << vector_bit); 2712} 2713 2714/** 2715 * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses 2716 * @hw: pointer to hardware structure 2717 * @mc_addr_list: the list of new multicast addresses 2718 * @mc_addr_count: number of addresses 2719 * @next: iterator function to walk the multicast address list 2720 * @clear: flag, when set clears the table beforehand 2721 * 2722 * When the clear flag is set, the given list replaces any existing list. 2723 * Hashes the given addresses into the multicast table. 2724 **/ 2725s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw, u8 *mc_addr_list, 2726 u32 mc_addr_count, ixgbe_mc_addr_itr next, 2727 bool clear) 2728{ 2729 u32 i; 2730 u32 vmdq; 2731 2732 DEBUGFUNC("ixgbe_update_mc_addr_list_generic"); 2733 2734 /* 2735 * Set the new number of MC addresses that we are being requested to 2736 * use. 2737 */ 2738 hw->addr_ctrl.num_mc_addrs = mc_addr_count; 2739 hw->addr_ctrl.mta_in_use = 0; 2740 2741 /* Clear mta_shadow */ 2742 if (clear) { 2743 DEBUGOUT(" Clearing MTA\n"); 2744 memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); 2745 } 2746 2747 /* Update mta_shadow */ 2748 for (i = 0; i < mc_addr_count; i++) { 2749 DEBUGOUT(" Adding the multicast addresses:\n"); 2750 ixgbe_set_mta(hw, next(hw, &mc_addr_list, &vmdq)); 2751 } 2752 2753 /* Enable mta */ 2754 for (i = 0; i < hw->mac.mcft_size; i++) 2755 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i, 2756 hw->mac.mta_shadow[i]); 2757 2758 if (hw->addr_ctrl.mta_in_use > 0) 2759 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, 2760 IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); 2761 2762 DEBUGOUT("ixgbe_update_mc_addr_list_generic Complete\n"); 2763 return IXGBE_SUCCESS; 2764} 2765 2766/** 2767 * ixgbe_enable_mc_generic - Enable multicast address in RAR 2768 * @hw: pointer to hardware structure 2769 * 2770 * Enables multicast address in RAR and the use of the multicast hash table. 2771 **/ 2772s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw) 2773{ 2774 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; 2775 2776 DEBUGFUNC("ixgbe_enable_mc_generic"); 2777 2778 if (a->mta_in_use > 0) 2779 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE | 2780 hw->mac.mc_filter_type); 2781 2782 return IXGBE_SUCCESS; 2783} 2784 2785/** 2786 * ixgbe_disable_mc_generic - Disable multicast address in RAR 2787 * @hw: pointer to hardware structure 2788 * 2789 * Disables multicast address in RAR and the use of the multicast hash table. 2790 **/ 2791s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) 2792{ 2793 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; 2794 2795 DEBUGFUNC("ixgbe_disable_mc_generic"); 2796 2797 if (a->mta_in_use > 0) 2798 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); 2799 2800 return IXGBE_SUCCESS; 2801} 2802 2803/** 2804 * ixgbe_fc_enable_generic - Enable flow control 2805 * @hw: pointer to hardware structure 2806 * 2807 * Enable flow control according to the current settings. 2808 **/ 2809s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) 2810{ 2811 s32 ret_val = IXGBE_SUCCESS; 2812 u32 mflcn_reg, fccfg_reg; 2813 u32 reg; 2814 u32 fcrtl, fcrth; 2815 int i; 2816 2817 DEBUGFUNC("ixgbe_fc_enable_generic"); 2818 2819 /* Validate the water mark configuration */ 2820 if (!hw->fc.pause_time) { 2821 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 2822 goto out; 2823 } 2824 2825 /* Low water mark of zero causes XOFF floods */ 2826 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 2827 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 2828 hw->fc.high_water[i]) { 2829 if (!hw->fc.low_water[i] || 2830 hw->fc.low_water[i] >= hw->fc.high_water[i]) { 2831 DEBUGOUT("Invalid water mark configuration\n"); 2832 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 2833 goto out; 2834 } 2835 } 2836 } 2837 2838 /* Negotiate the fc mode to use */ 2839 hw->mac.ops.fc_autoneg(hw); 2840 2841 /* Disable any previous flow control settings */ 2842 mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); 2843 mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE); 2844 2845 fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG); 2846 fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY); 2847 2848 /* 2849 * The possible values of fc.current_mode are: 2850 * 0: Flow control is completely disabled 2851 * 1: Rx flow control is enabled (we can receive pause frames, 2852 * but not send pause frames). 2853 * 2: Tx flow control is enabled (we can send pause frames but 2854 * we do not support receiving pause frames). 2855 * 3: Both Rx and Tx flow control (symmetric) are enabled. 2856 * other: Invalid. 2857 */ 2858 switch (hw->fc.current_mode) { 2859 case ixgbe_fc_none: 2860 /* 2861 * Flow control is disabled by software override or autoneg. 2862 * The code below will actually disable it in the HW. 2863 */ 2864 break; 2865 case ixgbe_fc_rx_pause: 2866 /* 2867 * Rx Flow control is enabled and Tx Flow control is 2868 * disabled by software override. Since there really 2869 * isn't a way to advertise that we are capable of RX 2870 * Pause ONLY, we will advertise that we support both 2871 * symmetric and asymmetric Rx PAUSE. Later, we will 2872 * disable the adapter's ability to send PAUSE frames. 2873 */ 2874 mflcn_reg |= IXGBE_MFLCN_RFCE; 2875 break; 2876 case ixgbe_fc_tx_pause: 2877 /* 2878 * Tx Flow control is enabled, and Rx Flow control is 2879 * disabled by software override. 2880 */ 2881 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; 2882 break; 2883 case ixgbe_fc_full: 2884 /* Flow control (both Rx and Tx) is enabled by SW override. */ 2885 mflcn_reg |= IXGBE_MFLCN_RFCE; 2886 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; 2887 break; 2888 default: 2889 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, 2890 "Flow control param set incorrectly\n"); 2891 ret_val = IXGBE_ERR_CONFIG; 2892 goto out; 2893 break; 2894 } 2895 2896 /* Set 802.3x based flow control settings. */ 2897 mflcn_reg |= IXGBE_MFLCN_DPF; 2898 IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); 2899 IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); 2900 2901 2902 /* Set up and enable Rx high/low water mark thresholds, enable XON. */ 2903 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 2904 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 2905 hw->fc.high_water[i]) { 2906 fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE; 2907 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl); 2908 fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; 2909 } else { 2910 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0); 2911 /* 2912 * In order to prevent Tx hangs when the internal Tx 2913 * switch is enabled we must set the high water mark 2914 * to the Rx packet buffer size - 24KB. This allows 2915 * the Tx switch to function even under heavy Rx 2916 * workloads. 2917 */ 2918 fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576; 2919 } 2920 2921 IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth); 2922 } 2923 2924 /* Configure pause time (2 TCs per register) */ 2925 reg = hw->fc.pause_time * 0x00010001; 2926 for (i = 0; i < (IXGBE_DCB_MAX_TRAFFIC_CLASS / 2); i++) 2927 IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); 2928 2929 /* Configure flow control refresh threshold value */ 2930 IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); 2931 2932out: 2933 return ret_val; 2934} 2935 2936/** 2937 * ixgbe_negotiate_fc - Negotiate flow control 2938 * @hw: pointer to hardware structure 2939 * @adv_reg: flow control advertised settings 2940 * @lp_reg: link partner's flow control settings 2941 * @adv_sym: symmetric pause bit in advertisement 2942 * @adv_asm: asymmetric pause bit in advertisement 2943 * @lp_sym: symmetric pause bit in link partner advertisement 2944 * @lp_asm: asymmetric pause bit in link partner advertisement 2945 * 2946 * Find the intersection between advertised settings and link partner's 2947 * advertised settings 2948 **/ 2949s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, 2950 u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) 2951{ 2952 if ((!(adv_reg)) || (!(lp_reg))) { 2953 ERROR_REPORT3(IXGBE_ERROR_UNSUPPORTED, 2954 "Local or link partner's advertised flow control " 2955 "settings are NULL. Local: %x, link partner: %x\n", 2956 adv_reg, lp_reg); 2957 return IXGBE_ERR_FC_NOT_NEGOTIATED; 2958 } 2959 2960 if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { 2961 /* 2962 * Now we need to check if the user selected Rx ONLY 2963 * of pause frames. In this case, we had to advertise 2964 * FULL flow control because we could not advertise RX 2965 * ONLY. Hence, we must now check to see if we need to 2966 * turn OFF the TRANSMISSION of PAUSE frames. 2967 */ 2968 if (hw->fc.requested_mode == ixgbe_fc_full) { 2969 hw->fc.current_mode = ixgbe_fc_full; 2970 DEBUGOUT("Flow Control = FULL.\n"); 2971 } else { 2972 hw->fc.current_mode = ixgbe_fc_rx_pause; 2973 DEBUGOUT("Flow Control=RX PAUSE frames only\n"); 2974 } 2975 } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && 2976 (lp_reg & lp_sym) && (lp_reg & lp_asm)) { 2977 hw->fc.current_mode = ixgbe_fc_tx_pause; 2978 DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); 2979 } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && 2980 !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { 2981 hw->fc.current_mode = ixgbe_fc_rx_pause; 2982 DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); 2983 } else { 2984 hw->fc.current_mode = ixgbe_fc_none; 2985 DEBUGOUT("Flow Control = NONE.\n"); 2986 } 2987 return IXGBE_SUCCESS; 2988} 2989 2990/** 2991 * ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber 2992 * @hw: pointer to hardware structure 2993 * 2994 * Enable flow control according on 1 gig fiber. 2995 **/ 2996static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw) 2997{ 2998 u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; 2999 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 3000 3001 /* 3002 * On multispeed fiber at 1g, bail out if 3003 * - link is up but AN did not complete, or if 3004 * - link is up and AN completed but timed out 3005 */ 3006 3007 linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); 3008 if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || 3009 (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) { 3010 DEBUGOUT("Auto-Negotiation did not complete or timed out\n"); 3011 goto out; 3012 } 3013 3014 pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); 3015 pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); 3016 3017 ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg, 3018 pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE, 3019 IXGBE_PCS1GANA_ASM_PAUSE, 3020 IXGBE_PCS1GANA_SYM_PAUSE, 3021 IXGBE_PCS1GANA_ASM_PAUSE); 3022 3023out: 3024 return ret_val; 3025} 3026 3027/** 3028 * ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37 3029 * @hw: pointer to hardware structure 3030 * 3031 * Enable flow control according to IEEE clause 37. 3032 **/ 3033static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw) 3034{ 3035 u32 links2, anlp1_reg, autoc_reg, links; 3036 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 3037 3038 /* 3039 * On backplane, bail out if 3040 * - backplane autoneg was not completed, or if 3041 * - we are 82599 and link partner is not AN enabled 3042 */ 3043 links = IXGBE_READ_REG(hw, IXGBE_LINKS); 3044 if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) { 3045 DEBUGOUT("Auto-Negotiation did not complete\n"); 3046 goto out; 3047 } 3048 3049 if (hw->mac.type == ixgbe_mac_82599EB) { 3050 links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2); 3051 if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) { 3052 DEBUGOUT("Link partner is not AN enabled\n"); 3053 goto out; 3054 } 3055 } 3056 /* 3057 * Read the 10g AN autoc and LP ability registers and resolve 3058 * local flow control settings accordingly 3059 */ 3060 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 3061 anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); 3062 3063 ret_val = ixgbe_negotiate_fc(hw, autoc_reg, 3064 anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE, 3065 IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE); 3066 3067out: 3068 return ret_val; 3069} 3070 3071/** 3072 * ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37 3073 * @hw: pointer to hardware structure 3074 * 3075 * Enable flow control according to IEEE clause 37. 3076 **/ 3077static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw) 3078{ 3079 u16 technology_ability_reg = 0; 3080 u16 lp_technology_ability_reg = 0; 3081 3082 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 3083 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 3084 &technology_ability_reg); 3085 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_LP, 3086 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 3087 &lp_technology_ability_reg); 3088 3089 return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg, 3090 (u32)lp_technology_ability_reg, 3091 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE, 3092 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE); 3093} 3094 3095/** 3096 * ixgbe_fc_autoneg - Configure flow control 3097 * @hw: pointer to hardware structure 3098 * 3099 * Compares our advertised flow control capabilities to those advertised by 3100 * our link partner, and determines the proper flow control mode to use. 3101 **/ 3102void ixgbe_fc_autoneg(struct ixgbe_hw *hw) 3103{ 3104 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 3105 ixgbe_link_speed speed; 3106 bool link_up; 3107 3108 DEBUGFUNC("ixgbe_fc_autoneg"); 3109 3110 /* 3111 * AN should have completed when the cable was plugged in. 3112 * Look for reasons to bail out. Bail out if: 3113 * - FC autoneg is disabled, or if 3114 * - link is not up. 3115 */ 3116 if (hw->fc.disable_fc_autoneg) { 3117 ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, 3118 "Flow control autoneg is disabled"); 3119 goto out; 3120 } 3121 3122 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 3123 if (!link_up) { 3124 ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down"); 3125 goto out; 3126 } 3127 3128 switch (hw->phy.media_type) { 3129 /* Autoneg flow control on fiber adapters */ 3130 case ixgbe_media_type_fiber_fixed: 3131 case ixgbe_media_type_fiber_qsfp: 3132 case ixgbe_media_type_fiber: 3133 if (speed == IXGBE_LINK_SPEED_1GB_FULL) 3134 ret_val = ixgbe_fc_autoneg_fiber(hw); 3135 break; 3136 3137 /* Autoneg flow control on backplane adapters */ 3138 case ixgbe_media_type_backplane: 3139 ret_val = ixgbe_fc_autoneg_backplane(hw); 3140 break; 3141 3142 /* Autoneg flow control on copper adapters */ 3143 case ixgbe_media_type_copper: 3144 if (ixgbe_device_supports_autoneg_fc(hw)) 3145 ret_val = ixgbe_fc_autoneg_copper(hw); 3146 break; 3147 3148 default: 3149 break; 3150 } 3151 3152out: 3153 if (ret_val == IXGBE_SUCCESS) { 3154 hw->fc.fc_was_autonegged = TRUE; 3155 } else { 3156 hw->fc.fc_was_autonegged = FALSE; 3157 hw->fc.current_mode = hw->fc.requested_mode; 3158 } 3159} 3160 3161/* 3162 * ixgbe_pcie_timeout_poll - Return number of times to poll for completion 3163 * @hw: pointer to hardware structure 3164 * 3165 * System-wide timeout range is encoded in PCIe Device Control2 register. 3166 * 3167 * Add 10% to specified maximum and return the number of times to poll for 3168 * completion timeout, in units of 100 microsec. Never return less than 3169 * 800 = 80 millisec. 3170 */ 3171static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw) 3172{ 3173 s16 devctl2; 3174 u32 pollcnt; 3175 3176 devctl2 = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_CONTROL2); 3177 devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK; 3178 3179 switch (devctl2) { 3180 case IXGBE_PCIDEVCTRL2_65_130ms: 3181 pollcnt = 1300; /* 130 millisec */ 3182 break; 3183 case IXGBE_PCIDEVCTRL2_260_520ms: 3184 pollcnt = 5200; /* 520 millisec */ 3185 break; 3186 case IXGBE_PCIDEVCTRL2_1_2s: 3187 pollcnt = 20000; /* 2 sec */ 3188 break; 3189 case IXGBE_PCIDEVCTRL2_4_8s: 3190 pollcnt = 80000; /* 8 sec */ 3191 break; 3192 case IXGBE_PCIDEVCTRL2_17_34s: 3193 pollcnt = 34000; /* 34 sec */ 3194 break; 3195 case IXGBE_PCIDEVCTRL2_50_100us: /* 100 microsecs */ 3196 case IXGBE_PCIDEVCTRL2_1_2ms: /* 2 millisecs */ 3197 case IXGBE_PCIDEVCTRL2_16_32ms: /* 32 millisec */ 3198 case IXGBE_PCIDEVCTRL2_16_32ms_def: /* 32 millisec default */ 3199 default: 3200 pollcnt = 800; /* 80 millisec minimum */ 3201 break; 3202 } 3203 3204 /* add 10% to spec maximum */ 3205 return (pollcnt * 11) / 10; 3206} 3207 3208/** 3209 * ixgbe_disable_pcie_master - Disable PCI-express master access 3210 * @hw: pointer to hardware structure 3211 * 3212 * Disables PCI-Express master access and verifies there are no pending 3213 * requests. IXGBE_ERR_MASTER_REQUESTS_PENDING is returned if master disable 3214 * bit hasn't caused the master requests to be disabled, else IXGBE_SUCCESS 3215 * is returned signifying master requests disabled. 3216 **/ 3217s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) 3218{ 3219 s32 status = IXGBE_SUCCESS; 3220 u32 i, poll; 3221 u16 value; 3222 3223 DEBUGFUNC("ixgbe_disable_pcie_master"); 3224 3225 /* Always set this bit to ensure any future transactions are blocked */ 3226 IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS); 3227 3228 /* Exit if master requests are blocked */ 3229 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) || 3230 IXGBE_REMOVED(hw->hw_addr)) 3231 goto out; 3232 3233 /* Poll for master request bit to clear */ 3234 for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) { 3235 usec_delay(100); 3236 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO)) 3237 goto out; 3238 } 3239 3240 /* 3241 * Two consecutive resets are required via CTRL.RST per datasheet 3242 * 5.2.5.3.2 Master Disable. We set a flag to inform the reset routine 3243 * of this need. The first reset prevents new master requests from 3244 * being issued by our device. We then must wait 1usec or more for any 3245 * remaining completions from the PCIe bus to trickle in, and then reset 3246 * again to clear out any effects they may have had on our device. 3247 */ 3248 DEBUGOUT("GIO Master Disable bit didn't clear - requesting resets\n"); 3249 hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; 3250 3251 if (hw->mac.type >= ixgbe_mac_X550) 3252 goto out; 3253 3254 /* 3255 * Before proceeding, make sure that the PCIe block does not have 3256 * transactions pending. 3257 */ 3258 poll = ixgbe_pcie_timeout_poll(hw); 3259 for (i = 0; i < poll; i++) { 3260 usec_delay(100); 3261 value = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_STATUS); 3262 if (IXGBE_REMOVED(hw->hw_addr)) 3263 goto out; 3264 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) 3265 goto out; 3266 } 3267 3268 ERROR_REPORT1(IXGBE_ERROR_POLLING, 3269 "PCIe transaction pending bit also did not clear.\n"); 3270 status = IXGBE_ERR_MASTER_REQUESTS_PENDING; 3271 3272out: 3273 return status; 3274} 3275 3276/** 3277 * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore 3278 * @hw: pointer to hardware structure 3279 * @mask: Mask to specify which semaphore to acquire 3280 * 3281 * Acquires the SWFW semaphore through the GSSR register for the specified 3282 * function (CSR, PHY0, PHY1, EEPROM, Flash) 3283 **/ 3284s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask) 3285{ 3286 u32 gssr = 0; 3287 u32 swmask = mask; 3288 u32 fwmask = mask << 5; 3289 u32 timeout = 200; 3290 u32 i; 3291 3292 DEBUGFUNC("ixgbe_acquire_swfw_sync"); 3293 3294 for (i = 0; i < timeout; i++) { 3295 /* 3296 * SW NVM semaphore bit is used for access to all 3297 * SW_FW_SYNC bits (not just NVM) 3298 */ 3299 if (ixgbe_get_eeprom_semaphore(hw)) 3300 return IXGBE_ERR_SWFW_SYNC; 3301 3302 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); 3303 if (!(gssr & (fwmask | swmask))) { 3304 gssr |= swmask; 3305 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); 3306 ixgbe_release_eeprom_semaphore(hw); 3307 return IXGBE_SUCCESS; 3308 } else { 3309 /* Resource is currently in use by FW or SW */ 3310 ixgbe_release_eeprom_semaphore(hw); 3311 msec_delay(5); 3312 } 3313 } 3314 3315 /* If time expired clear the bits holding the lock and retry */ 3316 if (gssr & (fwmask | swmask)) 3317 ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask)); 3318 3319 msec_delay(5); 3320 return IXGBE_ERR_SWFW_SYNC; 3321} 3322 3323/** 3324 * ixgbe_release_swfw_sync - Release SWFW semaphore 3325 * @hw: pointer to hardware structure 3326 * @mask: Mask to specify which semaphore to release 3327 * 3328 * Releases the SWFW semaphore through the GSSR register for the specified 3329 * function (CSR, PHY0, PHY1, EEPROM, Flash) 3330 **/ 3331void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask) 3332{ 3333 u32 gssr; 3334 u32 swmask = mask; 3335 3336 DEBUGFUNC("ixgbe_release_swfw_sync"); 3337 3338 ixgbe_get_eeprom_semaphore(hw); 3339 3340 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); 3341 gssr &= ~swmask; 3342 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); 3343 3344 ixgbe_release_eeprom_semaphore(hw); 3345} 3346 3347/** 3348 * ixgbe_disable_sec_rx_path_generic - Stops the receive data path 3349 * @hw: pointer to hardware structure 3350 * 3351 * Stops the receive data path and waits for the HW to internally empty 3352 * the Rx security block 3353 **/ 3354s32 ixgbe_disable_sec_rx_path_generic(struct ixgbe_hw *hw) 3355{ 3356#define IXGBE_MAX_SECRX_POLL 40 3357 3358 int i; 3359 int secrxreg; 3360 3361 DEBUGFUNC("ixgbe_disable_sec_rx_path_generic"); 3362 3363 3364 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); 3365 secrxreg |= IXGBE_SECRXCTRL_RX_DIS; 3366 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); 3367 for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) { 3368 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT); 3369 if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY) 3370 break; 3371 else 3372 /* Use interrupt-safe sleep just in case */ 3373 usec_delay(1000); 3374 } 3375 3376 /* For informational purposes only */ 3377 if (i >= IXGBE_MAX_SECRX_POLL) 3378 DEBUGOUT("Rx unit being enabled before security " 3379 "path fully disabled. Continuing with init.\n"); 3380 3381 return IXGBE_SUCCESS; 3382} 3383 3384/** 3385 * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read 3386 * @hw: pointer to hardware structure 3387 * @reg_val: Value we read from AUTOC 3388 * 3389 * The default case requires no protection so just to the register read. 3390 */ 3391s32 prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val) 3392{ 3393 *locked = FALSE; 3394 *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC); 3395 return IXGBE_SUCCESS; 3396} 3397 3398/** 3399 * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write 3400 * @hw: pointer to hardware structure 3401 * @reg_val: value to write to AUTOC 3402 * @locked: bool to indicate whether the SW/FW lock was already taken by 3403 * previous read. 3404 * 3405 * The default case requires no protection so just to the register write. 3406 */ 3407s32 prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked) 3408{ 3409 UNREFERENCED_1PARAMETER(locked); 3410 3411 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val); 3412 return IXGBE_SUCCESS; 3413} 3414 3415/** 3416 * ixgbe_enable_sec_rx_path_generic - Enables the receive data path 3417 * @hw: pointer to hardware structure 3418 * 3419 * Enables the receive data path. 3420 **/ 3421s32 ixgbe_enable_sec_rx_path_generic(struct ixgbe_hw *hw) 3422{ 3423 u32 secrxreg; 3424 3425 DEBUGFUNC("ixgbe_enable_sec_rx_path_generic"); 3426 3427 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); 3428 secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS; 3429 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); 3430 IXGBE_WRITE_FLUSH(hw); 3431 3432 return IXGBE_SUCCESS; 3433} 3434 3435/** 3436 * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit 3437 * @hw: pointer to hardware structure 3438 * @regval: register value to write to RXCTRL 3439 * 3440 * Enables the Rx DMA unit 3441 **/ 3442s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval) 3443{ 3444 DEBUGFUNC("ixgbe_enable_rx_dma_generic"); 3445 3446 if (regval & IXGBE_RXCTRL_RXEN) 3447 ixgbe_enable_rx(hw); 3448 else 3449 ixgbe_disable_rx(hw); 3450 3451 return IXGBE_SUCCESS; 3452} 3453 3454/** 3455 * ixgbe_blink_led_start_generic - Blink LED based on index. 3456 * @hw: pointer to hardware structure 3457 * @index: led number to blink 3458 **/ 3459s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index) 3460{ 3461 ixgbe_link_speed speed = 0; 3462 bool link_up = 0; 3463 u32 autoc_reg = 0; 3464 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 3465 s32 ret_val = IXGBE_SUCCESS; 3466 bool locked = FALSE; 3467 3468 DEBUGFUNC("ixgbe_blink_led_start_generic"); 3469 3470 if (index > 3) 3471 return IXGBE_ERR_PARAM; 3472 3473 /* 3474 * Link must be up to auto-blink the LEDs; 3475 * Force it if link is down. 3476 */ 3477 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 3478 3479 if (!link_up) { 3480 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); 3481 if (ret_val != IXGBE_SUCCESS) 3482 goto out; 3483 3484 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 3485 autoc_reg |= IXGBE_AUTOC_FLU; 3486 3487 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); 3488 if (ret_val != IXGBE_SUCCESS) 3489 goto out; 3490 3491 IXGBE_WRITE_FLUSH(hw); 3492 msec_delay(10); 3493 } 3494 3495 led_reg &= ~IXGBE_LED_MODE_MASK(index); 3496 led_reg |= IXGBE_LED_BLINK(index); 3497 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 3498 IXGBE_WRITE_FLUSH(hw); 3499 3500out: 3501 return ret_val; 3502} 3503 3504/** 3505 * ixgbe_blink_led_stop_generic - Stop blinking LED based on index. 3506 * @hw: pointer to hardware structure 3507 * @index: led number to stop blinking 3508 **/ 3509s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index) 3510{ 3511 u32 autoc_reg = 0; 3512 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 3513 s32 ret_val = IXGBE_SUCCESS; 3514 bool locked = FALSE; 3515 3516 DEBUGFUNC("ixgbe_blink_led_stop_generic"); 3517 3518 if (index > 3) 3519 return IXGBE_ERR_PARAM; 3520 3521 3522 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); 3523 if (ret_val != IXGBE_SUCCESS) 3524 goto out; 3525 3526 autoc_reg &= ~IXGBE_AUTOC_FLU; 3527 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 3528 3529 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); 3530 if (ret_val != IXGBE_SUCCESS) 3531 goto out; 3532 3533 led_reg &= ~IXGBE_LED_MODE_MASK(index); 3534 led_reg &= ~IXGBE_LED_BLINK(index); 3535 led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index); 3536 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 3537 IXGBE_WRITE_FLUSH(hw); 3538 3539out: 3540 return ret_val; 3541} 3542 3543/** 3544 * ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM 3545 * @hw: pointer to hardware structure 3546 * @san_mac_offset: SAN MAC address offset 3547 * 3548 * This function will read the EEPROM location for the SAN MAC address 3549 * pointer, and returns the value at that location. This is used in both 3550 * get and set mac_addr routines. 3551 **/ 3552static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw, 3553 u16 *san_mac_offset) 3554{ 3555 s32 ret_val; 3556 3557 DEBUGFUNC("ixgbe_get_san_mac_addr_offset"); 3558 3559 /* 3560 * First read the EEPROM pointer to see if the MAC addresses are 3561 * available. 3562 */ 3563 ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR, 3564 san_mac_offset); 3565 if (ret_val) { 3566 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 3567 "eeprom at offset %d failed", 3568 IXGBE_SAN_MAC_ADDR_PTR); 3569 } 3570 3571 return ret_val; 3572} 3573 3574/** 3575 * ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM 3576 * @hw: pointer to hardware structure 3577 * @san_mac_addr: SAN MAC address 3578 * 3579 * Reads the SAN MAC address from the EEPROM, if it's available. This is 3580 * per-port, so set_lan_id() must be called before reading the addresses. 3581 * set_lan_id() is called by identify_sfp(), but this cannot be relied 3582 * upon for non-SFP connections, so we must call it here. 3583 **/ 3584s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr) 3585{ 3586 u16 san_mac_data, san_mac_offset; 3587 u8 i; 3588 s32 ret_val; 3589 3590 DEBUGFUNC("ixgbe_get_san_mac_addr_generic"); 3591 3592 /* 3593 * First read the EEPROM pointer to see if the MAC addresses are 3594 * available. If they're not, no point in calling set_lan_id() here. 3595 */ 3596 ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset); 3597 if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF) 3598 goto san_mac_addr_out; 3599 3600 /* make sure we know which port we need to program */ 3601 hw->mac.ops.set_lan_id(hw); 3602 /* apply the port offset to the address offset */ 3603 (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : 3604 (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); 3605 for (i = 0; i < 3; i++) { 3606 ret_val = hw->eeprom.ops.read(hw, san_mac_offset, 3607 &san_mac_data); 3608 if (ret_val) { 3609 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 3610 "eeprom read at offset %d failed", 3611 san_mac_offset); 3612 goto san_mac_addr_out; 3613 } 3614 san_mac_addr[i * 2] = (u8)(san_mac_data); 3615 san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8); 3616 san_mac_offset++; 3617 } 3618 return IXGBE_SUCCESS; 3619 3620san_mac_addr_out: 3621 /* 3622 * No addresses available in this EEPROM. It's not an 3623 * error though, so just wipe the local address and return. 3624 */ 3625 for (i = 0; i < 6; i++) 3626 san_mac_addr[i] = 0xFF; 3627 return IXGBE_SUCCESS; 3628} 3629 3630/** 3631 * ixgbe_set_san_mac_addr_generic - Write the SAN MAC address to the EEPROM 3632 * @hw: pointer to hardware structure 3633 * @san_mac_addr: SAN MAC address 3634 * 3635 * Write a SAN MAC address to the EEPROM. 3636 **/ 3637s32 ixgbe_set_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr) 3638{ 3639 s32 ret_val; 3640 u16 san_mac_data, san_mac_offset; 3641 u8 i; 3642 3643 DEBUGFUNC("ixgbe_set_san_mac_addr_generic"); 3644 3645 /* Look for SAN mac address pointer. If not defined, return */ 3646 ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset); 3647 if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF) 3648 return IXGBE_ERR_NO_SAN_ADDR_PTR; 3649 3650 /* Make sure we know which port we need to write */ 3651 hw->mac.ops.set_lan_id(hw); 3652 /* Apply the port offset to the address offset */ 3653 (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : 3654 (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); 3655 3656 for (i = 0; i < 3; i++) { 3657 san_mac_data = (u16)((u16)(san_mac_addr[i * 2 + 1]) << 8); 3658 san_mac_data |= (u16)(san_mac_addr[i * 2]); 3659 hw->eeprom.ops.write(hw, san_mac_offset, san_mac_data); 3660 san_mac_offset++; 3661 } 3662 3663 return IXGBE_SUCCESS; 3664} 3665 3666/** 3667 * ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count 3668 * @hw: pointer to hardware structure 3669 * 3670 * Read PCIe configuration space, and get the MSI-X vector count from 3671 * the capabilities table. 3672 **/ 3673u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw) 3674{ 3675 u16 msix_count = 1; 3676 u16 max_msix_count; 3677 u16 pcie_offset; 3678 3679 switch (hw->mac.type) { 3680 case ixgbe_mac_82598EB: 3681 pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS; 3682 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598; 3683 break; 3684 case ixgbe_mac_82599EB: 3685 case ixgbe_mac_X540: 3686 case ixgbe_mac_X550: 3687 case ixgbe_mac_X550EM_x: 3688 case ixgbe_mac_X550EM_a: 3689 pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS; 3690 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599; 3691 break; 3692 default: 3693 return msix_count; 3694 } 3695 3696 DEBUGFUNC("ixgbe_get_pcie_msix_count_generic"); 3697 msix_count = IXGBE_READ_PCIE_WORD(hw, pcie_offset); 3698 if (IXGBE_REMOVED(hw->hw_addr)) 3699 msix_count = 0; 3700 msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK; 3701 3702 /* MSI-X count is zero-based in HW */ 3703 msix_count++; 3704 3705 if (msix_count > max_msix_count) 3706 msix_count = max_msix_count; 3707 3708 return msix_count; 3709} 3710 3711/** 3712 * ixgbe_insert_mac_addr_generic - Find a RAR for this mac address 3713 * @hw: pointer to hardware structure 3714 * @addr: Address to put into receive address register 3715 * @vmdq: VMDq pool to assign 3716 * 3717 * Puts an ethernet address into a receive address register, or 3718 * finds the rar that it is aleady in; adds to the pool list 3719 **/ 3720s32 ixgbe_insert_mac_addr_generic(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) 3721{ 3722 static const u32 NO_EMPTY_RAR_FOUND = 0xFFFFFFFF; 3723 u32 first_empty_rar = NO_EMPTY_RAR_FOUND; 3724 u32 rar; 3725 u32 rar_low, rar_high; 3726 u32 addr_low, addr_high; 3727 3728 DEBUGFUNC("ixgbe_insert_mac_addr_generic"); 3729 3730 /* swap bytes for HW little endian */ 3731 addr_low = addr[0] | (addr[1] << 8) 3732 | (addr[2] << 16) 3733 | (addr[3] << 24); 3734 addr_high = addr[4] | (addr[5] << 8); 3735 3736 /* 3737 * Either find the mac_id in rar or find the first empty space. 3738 * rar_highwater points to just after the highest currently used 3739 * rar in order to shorten the search. It grows when we add a new 3740 * rar to the top. 3741 */ 3742 for (rar = 0; rar < hw->mac.rar_highwater; rar++) { 3743 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar)); 3744 3745 if (((IXGBE_RAH_AV & rar_high) == 0) 3746 && first_empty_rar == NO_EMPTY_RAR_FOUND) { 3747 first_empty_rar = rar; 3748 } else if ((rar_high & 0xFFFF) == addr_high) { 3749 rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(rar)); 3750 if (rar_low == addr_low) 3751 break; /* found it already in the rars */ 3752 } 3753 } 3754 3755 if (rar < hw->mac.rar_highwater) { 3756 /* already there so just add to the pool bits */ 3757 ixgbe_set_vmdq(hw, rar, vmdq); 3758 } else if (first_empty_rar != NO_EMPTY_RAR_FOUND) { 3759 /* stick it into first empty RAR slot we found */ 3760 rar = first_empty_rar; 3761 ixgbe_set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 3762 } else if (rar == hw->mac.rar_highwater) { 3763 /* add it to the top of the list and inc the highwater mark */ 3764 ixgbe_set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 3765 hw->mac.rar_highwater++; 3766 } else if (rar >= hw->mac.num_rar_entries) { 3767 return IXGBE_ERR_INVALID_MAC_ADDR; 3768 } 3769 3770 /* 3771 * If we found rar[0], make sure the default pool bit (we use pool 0) 3772 * remains cleared to be sure default pool packets will get delivered 3773 */ 3774 if (rar == 0) 3775 ixgbe_clear_vmdq(hw, rar, 0); 3776 3777 return rar; 3778} 3779 3780/** 3781 * ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address 3782 * @hw: pointer to hardware struct 3783 * @rar: receive address register index to disassociate 3784 * @vmdq: VMDq pool index to remove from the rar 3785 **/ 3786s32 ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 3787{ 3788 u32 mpsar_lo, mpsar_hi; 3789 u32 rar_entries = hw->mac.num_rar_entries; 3790 3791 DEBUGFUNC("ixgbe_clear_vmdq_generic"); 3792 3793 /* Make sure we are using a valid rar index range */ 3794 if (rar >= rar_entries) { 3795 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 3796 "RAR index %d is out of range.\n", rar); 3797 return IXGBE_ERR_INVALID_ARGUMENT; 3798 } 3799 3800 mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); 3801 mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); 3802 3803 if (IXGBE_REMOVED(hw->hw_addr)) 3804 goto done; 3805 3806 if (!mpsar_lo && !mpsar_hi) 3807 goto done; 3808 3809 if (vmdq == IXGBE_CLEAR_VMDQ_ALL) { 3810 if (mpsar_lo) { 3811 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); 3812 mpsar_lo = 0; 3813 } 3814 if (mpsar_hi) { 3815 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); 3816 mpsar_hi = 0; 3817 } 3818 } else if (vmdq < 32) { 3819 mpsar_lo &= ~(1 << vmdq); 3820 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo); 3821 } else { 3822 mpsar_hi &= ~(1 << (vmdq - 32)); 3823 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi); 3824 } 3825 3826 /* was that the last pool using this rar? */ 3827 if (mpsar_lo == 0 && mpsar_hi == 0 && 3828 rar != 0 && rar != hw->mac.san_mac_rar_index) 3829 hw->mac.ops.clear_rar(hw, rar); 3830done: 3831 return IXGBE_SUCCESS; 3832} 3833 3834/** 3835 * ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address 3836 * @hw: pointer to hardware struct 3837 * @rar: receive address register index to associate with a VMDq index 3838 * @vmdq: VMDq pool index 3839 **/ 3840s32 ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 3841{ 3842 u32 mpsar; 3843 u32 rar_entries = hw->mac.num_rar_entries; 3844 3845 DEBUGFUNC("ixgbe_set_vmdq_generic"); 3846 3847 /* Make sure we are using a valid rar index range */ 3848 if (rar >= rar_entries) { 3849 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 3850 "RAR index %d is out of range.\n", rar); 3851 return IXGBE_ERR_INVALID_ARGUMENT; 3852 } 3853 3854 if (vmdq < 32) { 3855 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); 3856 mpsar |= 1 << vmdq; 3857 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar); 3858 } else { 3859 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); 3860 mpsar |= 1 << (vmdq - 32); 3861 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar); 3862 } 3863 return IXGBE_SUCCESS; 3864} 3865 3866/** 3867 * This function should only be involved in the IOV mode. 3868 * In IOV mode, Default pool is next pool after the number of 3869 * VFs advertized and not 0. 3870 * MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index] 3871 * 3872 * ixgbe_set_vmdq_san_mac - Associate default VMDq pool index with a rx address 3873 * @hw: pointer to hardware struct 3874 * @vmdq: VMDq pool index 3875 **/ 3876s32 ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq) 3877{ 3878 u32 rar = hw->mac.san_mac_rar_index; 3879 3880 DEBUGFUNC("ixgbe_set_vmdq_san_mac"); 3881 3882 if (vmdq < 32) { 3883 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 1 << vmdq); 3884 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); 3885 } else { 3886 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); 3887 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 1 << (vmdq - 32)); 3888 } 3889 3890 return IXGBE_SUCCESS; 3891} 3892 3893/** 3894 * ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array 3895 * @hw: pointer to hardware structure 3896 **/ 3897s32 ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw) 3898{ 3899 int i; 3900 3901 DEBUGFUNC("ixgbe_init_uta_tables_generic"); 3902 DEBUGOUT(" Clearing UTA\n"); 3903 3904 for (i = 0; i < 128; i++) 3905 IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0); 3906 3907 return IXGBE_SUCCESS; 3908} 3909 3910/** 3911 * ixgbe_find_vlvf_slot - find the vlanid or the first empty slot 3912 * @hw: pointer to hardware structure 3913 * @vlan: VLAN id to write to VLAN filter 3914 * 3915 * return the VLVF index where this VLAN id should be placed 3916 * 3917 **/ 3918s32 ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass) 3919{ 3920 s32 regindex, first_empty_slot; 3921 u32 bits; 3922 3923 /* short cut the special case */ 3924 if (vlan == 0) 3925 return 0; 3926 3927 /* if vlvf_bypass is set we don't want to use an empty slot, we 3928 * will simply bypass the VLVF if there are no entries present in the 3929 * VLVF that contain our VLAN 3930 */ 3931 first_empty_slot = vlvf_bypass ? IXGBE_ERR_NO_SPACE : 0; 3932 3933 /* add VLAN enable bit for comparison */ 3934 vlan |= IXGBE_VLVF_VIEN; 3935 3936 /* Search for the vlan id in the VLVF entries. Save off the first empty 3937 * slot found along the way. 3938 * 3939 * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1 3940 */ 3941 for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) { 3942 bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex)); 3943 if (bits == vlan) 3944 return regindex; 3945 if (!first_empty_slot && !bits) 3946 first_empty_slot = regindex; 3947 } 3948 3949 /* If we are here then we didn't find the VLAN. Return first empty 3950 * slot we found during our search, else error. 3951 */ 3952 if (!first_empty_slot) 3953 ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "No space in VLVF.\n"); 3954 3955 return first_empty_slot ? first_empty_slot : IXGBE_ERR_NO_SPACE; 3956} 3957 3958/** 3959 * ixgbe_set_vfta_generic - Set VLAN filter table 3960 * @hw: pointer to hardware structure 3961 * @vlan: VLAN id to write to VLAN filter 3962 * @vind: VMDq output index that maps queue to VLAN id in VLVFB 3963 * @vlan_on: boolean flag to turn on/off VLAN 3964 * @vlvf_bypass: boolean flag indicating updating default pool is okay 3965 * 3966 * Turn on/off specified VLAN in the VLAN filter table. 3967 **/ 3968s32 ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind, 3969 bool vlan_on, bool vlvf_bypass) 3970{ 3971 u32 regidx, vfta_delta, vfta; 3972 s32 ret_val; 3973 3974 DEBUGFUNC("ixgbe_set_vfta_generic"); 3975 3976 if (vlan > 4095 || vind > 63) 3977 return IXGBE_ERR_PARAM; 3978 3979 /* 3980 * this is a 2 part operation - first the VFTA, then the 3981 * VLVF and VLVFB if VT Mode is set 3982 * We don't write the VFTA until we know the VLVF part succeeded. 3983 */ 3984 3985 /* Part 1 3986 * The VFTA is a bitstring made up of 128 32-bit registers 3987 * that enable the particular VLAN id, much like the MTA: 3988 * bits[11-5]: which register 3989 * bits[4-0]: which bit in the register 3990 */ 3991 regidx = vlan / 32; 3992 vfta_delta = 1 << (vlan % 32); 3993 vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx)); 3994 3995 /* 3996 * vfta_delta represents the difference between the current value 3997 * of vfta and the value we want in the register. Since the diff 3998 * is an XOR mask we can just update the vfta using an XOR 3999 */ 4000 vfta_delta &= vlan_on ? ~vfta : vfta; 4001 vfta ^= vfta_delta; 4002 4003 /* Part 2 4004 * Call ixgbe_set_vlvf_generic to set VLVFB and VLVF 4005 */ 4006 ret_val = ixgbe_set_vlvf_generic(hw, vlan, vind, vlan_on, &vfta_delta, 4007 vfta, vlvf_bypass); 4008 if (ret_val != IXGBE_SUCCESS) { 4009 if (vlvf_bypass) 4010 goto vfta_update; 4011 return ret_val; 4012 } 4013 4014vfta_update: 4015 /* Update VFTA now that we are ready for traffic */ 4016 if (vfta_delta) 4017 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta); 4018 4019 return IXGBE_SUCCESS; 4020} 4021 4022/** 4023 * ixgbe_set_vlvf_generic - Set VLAN Pool Filter 4024 * @hw: pointer to hardware structure 4025 * @vlan: VLAN id to write to VLAN filter 4026 * @vind: VMDq output index that maps queue to VLAN id in VLVFB 4027 * @vlan_on: boolean flag to turn on/off VLAN in VLVF 4028 * @vfta_delta: pointer to the difference between the current value of VFTA 4029 * and the desired value 4030 * @vfta: the desired value of the VFTA 4031 * @vlvf_bypass: boolean flag indicating updating default pool is okay 4032 * 4033 * Turn on/off specified bit in VLVF table. 4034 **/ 4035s32 ixgbe_set_vlvf_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind, 4036 bool vlan_on, u32 *vfta_delta, u32 vfta, 4037 bool vlvf_bypass) 4038{ 4039 u32 bits; 4040 s32 vlvf_index; 4041 4042 DEBUGFUNC("ixgbe_set_vlvf_generic"); 4043 4044 if (vlan > 4095 || vind > 63) 4045 return IXGBE_ERR_PARAM; 4046 4047 /* If VT Mode is set 4048 * Either vlan_on 4049 * make sure the vlan is in VLVF 4050 * set the vind bit in the matching VLVFB 4051 * Or !vlan_on 4052 * clear the pool bit and possibly the vind 4053 */ 4054 if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE)) 4055 return IXGBE_SUCCESS; 4056 4057 vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass); 4058 if (vlvf_index < 0) 4059 return vlvf_index; 4060 4061 bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32)); 4062 4063 /* set the pool bit */ 4064 bits |= 1 << (vind % 32); 4065 if (vlan_on) 4066 goto vlvf_update; 4067 4068 /* clear the pool bit */ 4069 bits ^= 1 << (vind % 32); 4070 4071 if (!bits && 4072 !IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) { 4073 /* Clear VFTA first, then disable VLVF. Otherwise 4074 * we run the risk of stray packets leaking into 4075 * the PF via the default pool 4076 */ 4077 if (*vfta_delta) 4078 IXGBE_WRITE_REG(hw, IXGBE_VFTA(vlan / 32), vfta); 4079 4080 /* disable VLVF and clear remaining bit from pool */ 4081 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0); 4082 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0); 4083 4084 return IXGBE_SUCCESS; 4085 } 4086 4087 /* If there are still bits set in the VLVFB registers 4088 * for the VLAN ID indicated we need to see if the 4089 * caller is requesting that we clear the VFTA entry bit. 4090 * If the caller has requested that we clear the VFTA 4091 * entry bit but there are still pools/VFs using this VLAN 4092 * ID entry then ignore the request. We're not worried 4093 * about the case where we're turning the VFTA VLAN ID 4094 * entry bit on, only when requested to turn it off as 4095 * there may be multiple pools and/or VFs using the 4096 * VLAN ID entry. In that case we cannot clear the 4097 * VFTA bit until all pools/VFs using that VLAN ID have also 4098 * been cleared. This will be indicated by "bits" being 4099 * zero. 4100 */ 4101 *vfta_delta = 0; 4102 4103vlvf_update: 4104 /* record pool change and enable VLAN ID if not already enabled */ 4105 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits); 4106 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan); 4107 4108 return IXGBE_SUCCESS; 4109} 4110 4111/** 4112 * ixgbe_clear_vfta_generic - Clear VLAN filter table 4113 * @hw: pointer to hardware structure 4114 * 4115 * Clears the VLAN filer table, and the VMDq index associated with the filter 4116 **/ 4117s32 ixgbe_clear_vfta_generic(struct ixgbe_hw *hw) 4118{ 4119 u32 offset; 4120 4121 DEBUGFUNC("ixgbe_clear_vfta_generic"); 4122 4123 for (offset = 0; offset < hw->mac.vft_size; offset++) 4124 IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0); 4125 4126 for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) { 4127 IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0); 4128 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0); 4129 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0); 4130 } 4131 4132 return IXGBE_SUCCESS; 4133} 4134 4135/** 4136 * ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix 4137 * @hw: pointer to hardware structure 4138 * 4139 * Contains the logic to identify if we need to verify link for the 4140 * crosstalk fix 4141 **/ 4142static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw) 4143{ 4144 4145 /* Does FW say we need the fix */ 4146 if (!hw->need_crosstalk_fix) 4147 return FALSE; 4148 4149 /* Only consider SFP+ PHYs i.e. media type fiber */ 4150 switch (hw->mac.ops.get_media_type(hw)) { 4151 case ixgbe_media_type_fiber: 4152 case ixgbe_media_type_fiber_qsfp: 4153 break; 4154 default: 4155 return FALSE; 4156 } 4157 4158 return TRUE; 4159} 4160 4161/** 4162 * ixgbe_check_mac_link_generic - Determine link and speed status 4163 * @hw: pointer to hardware structure 4164 * @speed: pointer to link speed 4165 * @link_up: TRUE when link is up 4166 * @link_up_wait_to_complete: bool used to wait for link up or not 4167 * 4168 * Reads the links register to determine if link is up and the current speed 4169 **/ 4170s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed, 4171 bool *link_up, bool link_up_wait_to_complete) 4172{ 4173 u32 links_reg, links_orig; 4174 u32 i; 4175 4176 DEBUGFUNC("ixgbe_check_mac_link_generic"); 4177 4178 /* If Crosstalk fix enabled do the sanity check of making sure 4179 * the SFP+ cage is full. 4180 */ 4181 if (ixgbe_need_crosstalk_fix(hw)) { 4182 u32 sfp_cage_full; 4183 4184 switch (hw->mac.type) { 4185 case ixgbe_mac_82599EB: 4186 sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) & 4187 IXGBE_ESDP_SDP2; 4188 break; 4189 case ixgbe_mac_X550EM_x: 4190 case ixgbe_mac_X550EM_a: 4191 sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) & 4192 IXGBE_ESDP_SDP0; 4193 break; 4194 default: 4195 /* sanity check - No SFP+ devices here */ 4196 sfp_cage_full = FALSE; 4197 break; 4198 } 4199 4200 if (!sfp_cage_full) { 4201 *link_up = FALSE; 4202 *speed = IXGBE_LINK_SPEED_UNKNOWN; 4203 return IXGBE_SUCCESS; 4204 } 4205 } 4206 4207 /* clear the old state */ 4208 links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS); 4209 4210 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 4211 4212 if (links_orig != links_reg) { 4213 DEBUGOUT2("LINKS changed from %08X to %08X\n", 4214 links_orig, links_reg); 4215 } 4216 4217 if (link_up_wait_to_complete) { 4218 for (i = 0; i < hw->mac.max_link_up_time; i++) { 4219 if (links_reg & IXGBE_LINKS_UP) { 4220 *link_up = TRUE; 4221 break; 4222 } else { 4223 *link_up = FALSE; 4224 } 4225 msec_delay(100); 4226 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 4227 } 4228 } else { 4229 if (links_reg & IXGBE_LINKS_UP) 4230 *link_up = TRUE; 4231 else 4232 *link_up = FALSE; 4233 } 4234 4235 switch (links_reg & IXGBE_LINKS_SPEED_82599) { 4236 case IXGBE_LINKS_SPEED_10G_82599: 4237 *speed = IXGBE_LINK_SPEED_10GB_FULL; 4238 if (hw->mac.type >= ixgbe_mac_X550) { 4239 if (links_reg & IXGBE_LINKS_SPEED_NON_STD) 4240 *speed = IXGBE_LINK_SPEED_2_5GB_FULL; 4241 } 4242 break; 4243 case IXGBE_LINKS_SPEED_1G_82599: 4244 *speed = IXGBE_LINK_SPEED_1GB_FULL; 4245 break; 4246 case IXGBE_LINKS_SPEED_100_82599: 4247 *speed = IXGBE_LINK_SPEED_100_FULL; 4248 if (hw->mac.type == ixgbe_mac_X550) { 4249 if (links_reg & IXGBE_LINKS_SPEED_NON_STD) 4250 *speed = IXGBE_LINK_SPEED_5GB_FULL; 4251 } 4252 break; 4253 case IXGBE_LINKS_SPEED_10_X550EM_A: 4254 *speed = IXGBE_LINK_SPEED_UNKNOWN; 4255 if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T || 4256 hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) { 4257 *speed = IXGBE_LINK_SPEED_10_FULL; 4258 } 4259 break; 4260 default: 4261 *speed = IXGBE_LINK_SPEED_UNKNOWN; 4262 } 4263 4264 return IXGBE_SUCCESS; 4265} 4266 4267/** 4268 * ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from 4269 * the EEPROM 4270 * @hw: pointer to hardware structure 4271 * @wwnn_prefix: the alternative WWNN prefix 4272 * @wwpn_prefix: the alternative WWPN prefix 4273 * 4274 * This function will read the EEPROM from the alternative SAN MAC address 4275 * block to check the support for the alternative WWNN/WWPN prefix support. 4276 **/ 4277s32 ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix, 4278 u16 *wwpn_prefix) 4279{ 4280 u16 offset, caps; 4281 u16 alt_san_mac_blk_offset; 4282 4283 DEBUGFUNC("ixgbe_get_wwn_prefix_generic"); 4284 4285 /* clear output first */ 4286 *wwnn_prefix = 0xFFFF; 4287 *wwpn_prefix = 0xFFFF; 4288 4289 /* check if alternative SAN MAC is supported */ 4290 offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR; 4291 if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset)) 4292 goto wwn_prefix_err; 4293 4294 if ((alt_san_mac_blk_offset == 0) || 4295 (alt_san_mac_blk_offset == 0xFFFF)) 4296 goto wwn_prefix_out; 4297 4298 /* check capability in alternative san mac address block */ 4299 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET; 4300 if (hw->eeprom.ops.read(hw, offset, &caps)) 4301 goto wwn_prefix_err; 4302 if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN)) 4303 goto wwn_prefix_out; 4304 4305 /* get the corresponding prefix for WWNN/WWPN */ 4306 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET; 4307 if (hw->eeprom.ops.read(hw, offset, wwnn_prefix)) { 4308 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 4309 "eeprom read at offset %d failed", offset); 4310 } 4311 4312 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET; 4313 if (hw->eeprom.ops.read(hw, offset, wwpn_prefix)) 4314 goto wwn_prefix_err; 4315 4316wwn_prefix_out: 4317 return IXGBE_SUCCESS; 4318 4319wwn_prefix_err: 4320 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 4321 "eeprom read at offset %d failed", offset); 4322 return IXGBE_SUCCESS; 4323} 4324 4325/** 4326 * ixgbe_get_fcoe_boot_status_generic - Get FCOE boot status from EEPROM 4327 * @hw: pointer to hardware structure 4328 * @bs: the fcoe boot status 4329 * 4330 * This function will read the FCOE boot status from the iSCSI FCOE block 4331 **/ 4332s32 ixgbe_get_fcoe_boot_status_generic(struct ixgbe_hw *hw, u16 *bs) 4333{ 4334 u16 offset, caps, flags; 4335 s32 status; 4336 4337 DEBUGFUNC("ixgbe_get_fcoe_boot_status_generic"); 4338 4339 /* clear output first */ 4340 *bs = ixgbe_fcoe_bootstatus_unavailable; 4341 4342 /* check if FCOE IBA block is present */ 4343 offset = IXGBE_FCOE_IBA_CAPS_BLK_PTR; 4344 status = hw->eeprom.ops.read(hw, offset, &caps); 4345 if (status != IXGBE_SUCCESS) 4346 goto out; 4347 4348 if (!(caps & IXGBE_FCOE_IBA_CAPS_FCOE)) 4349 goto out; 4350 4351 /* check if iSCSI FCOE block is populated */ 4352 status = hw->eeprom.ops.read(hw, IXGBE_ISCSI_FCOE_BLK_PTR, &offset); 4353 if (status != IXGBE_SUCCESS) 4354 goto out; 4355 4356 if ((offset == 0) || (offset == 0xFFFF)) 4357 goto out; 4358 4359 /* read fcoe flags in iSCSI FCOE block */ 4360 offset = offset + IXGBE_ISCSI_FCOE_FLAGS_OFFSET; 4361 status = hw->eeprom.ops.read(hw, offset, &flags); 4362 if (status != IXGBE_SUCCESS) 4363 goto out; 4364 4365 if (flags & IXGBE_ISCSI_FCOE_FLAGS_ENABLE) 4366 *bs = ixgbe_fcoe_bootstatus_enabled; 4367 else 4368 *bs = ixgbe_fcoe_bootstatus_disabled; 4369 4370out: 4371 return status; 4372} 4373 4374/** 4375 * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing 4376 * @hw: pointer to hardware structure 4377 * @enable: enable or disable switch for MAC anti-spoofing 4378 * @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing 4379 * 4380 **/ 4381void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf) 4382{ 4383 int vf_target_reg = vf >> 3; 4384 int vf_target_shift = vf % 8; 4385 u32 pfvfspoof; 4386 4387 if (hw->mac.type == ixgbe_mac_82598EB) 4388 return; 4389 4390 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); 4391 if (enable) 4392 pfvfspoof |= (1 << vf_target_shift); 4393 else 4394 pfvfspoof &= ~(1 << vf_target_shift); 4395 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); 4396} 4397 4398/** 4399 * ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing 4400 * @hw: pointer to hardware structure 4401 * @enable: enable or disable switch for VLAN anti-spoofing 4402 * @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing 4403 * 4404 **/ 4405void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf) 4406{ 4407 int vf_target_reg = vf >> 3; 4408 int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT; 4409 u32 pfvfspoof; 4410 4411 if (hw->mac.type == ixgbe_mac_82598EB) 4412 return; 4413 4414 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); 4415 if (enable) 4416 pfvfspoof |= (1 << vf_target_shift); 4417 else 4418 pfvfspoof &= ~(1 << vf_target_shift); 4419 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); 4420} 4421 4422/** 4423 * ixgbe_get_device_caps_generic - Get additional device capabilities 4424 * @hw: pointer to hardware structure 4425 * @device_caps: the EEPROM word with the extra device capabilities 4426 * 4427 * This function will read the EEPROM location for the device capabilities, 4428 * and return the word through device_caps. 4429 **/ 4430s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps) 4431{ 4432 DEBUGFUNC("ixgbe_get_device_caps_generic"); 4433 4434 hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps); 4435 4436 return IXGBE_SUCCESS; 4437} 4438 4439/** 4440 * ixgbe_enable_relaxed_ordering_gen2 - Enable relaxed ordering 4441 * @hw: pointer to hardware structure 4442 * 4443 **/ 4444void ixgbe_enable_relaxed_ordering_gen2(struct ixgbe_hw *hw) 4445{ 4446 u32 regval; 4447 u32 i; 4448 4449 DEBUGFUNC("ixgbe_enable_relaxed_ordering_gen2"); 4450 4451 /* Enable relaxed ordering */ 4452 for (i = 0; i < hw->mac.max_tx_queues; i++) { 4453 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(i)); 4454 regval |= IXGBE_DCA_TXCTRL_DESC_WRO_EN; 4455 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(i), regval); 4456 } 4457 4458 for (i = 0; i < hw->mac.max_rx_queues; i++) { 4459 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 4460 regval |= IXGBE_DCA_RXCTRL_DATA_WRO_EN | 4461 IXGBE_DCA_RXCTRL_HEAD_WRO_EN; 4462 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 4463 } 4464 4465} 4466 4467/** 4468 * ixgbe_calculate_checksum - Calculate checksum for buffer 4469 * @buffer: pointer to EEPROM 4470 * @length: size of EEPROM to calculate a checksum for 4471 * Calculates the checksum for some buffer on a specified length. The 4472 * checksum calculated is returned. 4473 **/ 4474u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) 4475{ 4476 u32 i; 4477 u8 sum = 0; 4478 4479 DEBUGFUNC("ixgbe_calculate_checksum"); 4480 4481 if (!buffer) 4482 return 0; 4483 4484 for (i = 0; i < length; i++) 4485 sum += buffer[i]; 4486 4487 return (u8) (0 - sum); 4488} 4489 4490/** 4491 * ixgbe_hic_unlocked - Issue command to manageability block unlocked 4492 * @hw: pointer to the HW structure 4493 * @buffer: command to write and where the return status will be placed 4494 * @length: length of buffer, must be multiple of 4 bytes 4495 * @timeout: time in ms to wait for command completion 4496 * 4497 * Communicates with the manageability block. On success return IXGBE_SUCCESS 4498 * else returns semaphore error when encountering an error acquiring 4499 * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. 4500 * 4501 * This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held 4502 * by the caller. 4503 **/ 4504s32 ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length, 4505 u32 timeout) 4506{ 4507 u32 hicr, i, fwsts; 4508 u16 dword_len; 4509 4510 DEBUGFUNC("ixgbe_hic_unlocked"); 4511 4512 if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { 4513 DEBUGOUT1("Buffer length failure buffersize=%d.\n", length); 4514 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4515 } 4516 4517 /* Set bit 9 of FWSTS clearing FW reset indication */ 4518 fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS); 4519 IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI); 4520 4521 /* Check that the host interface is enabled. */ 4522 hicr = IXGBE_READ_REG(hw, IXGBE_HICR); 4523 if (!(hicr & IXGBE_HICR_EN)) { 4524 DEBUGOUT("IXGBE_HOST_EN bit disabled.\n"); 4525 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4526 } 4527 4528 /* Calculate length in DWORDs. We must be DWORD aligned */ 4529 if (length % sizeof(u32)) { 4530 DEBUGOUT("Buffer length failure, not aligned to dword"); 4531 return IXGBE_ERR_INVALID_ARGUMENT; 4532 } 4533 4534 dword_len = length >> 2; 4535 4536 /* The device driver writes the relevant command block 4537 * into the ram area. 4538 */ 4539 for (i = 0; i < dword_len; i++) 4540 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG, 4541 i, IXGBE_CPU_TO_LE32(buffer[i])); 4542 4543 /* Setting this bit tells the ARC that a new command is pending. */ 4544 IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C); 4545 4546 for (i = 0; i < timeout; i++) { 4547 hicr = IXGBE_READ_REG(hw, IXGBE_HICR); 4548 if (!(hicr & IXGBE_HICR_C)) 4549 break; 4550 msec_delay(1); 4551 } 4552 4553 /* Check command completion */ 4554 if ((timeout && i == timeout) || 4555 !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) { 4556 ERROR_REPORT1(IXGBE_ERROR_CAUTION, 4557 "Command has failed with no status valid.\n"); 4558 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4559 } 4560 4561 return IXGBE_SUCCESS; 4562} 4563 4564/** 4565 * ixgbe_host_interface_command - Issue command to manageability block 4566 * @hw: pointer to the HW structure 4567 * @buffer: contains the command to write and where the return status will 4568 * be placed 4569 * @length: length of buffer, must be multiple of 4 bytes 4570 * @timeout: time in ms to wait for command completion 4571 * @return_data: read and return data from the buffer (TRUE) or not (FALSE) 4572 * Needed because FW structures are big endian and decoding of 4573 * these fields can be 8 bit or 16 bit based on command. Decoding 4574 * is not easily understood without making a table of commands. 4575 * So we will leave this up to the caller to read back the data 4576 * in these cases. 4577 * 4578 * Communicates with the manageability block. On success return IXGBE_SUCCESS 4579 * else returns semaphore error when encountering an error acquiring 4580 * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. 4581 **/ 4582s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, u32 *buffer, 4583 u32 length, u32 timeout, bool return_data) 4584{ 4585 u32 hdr_size = sizeof(struct ixgbe_hic_hdr); 4586 u16 dword_len; 4587 u16 buf_len; 4588 s32 status; 4589 u32 bi; 4590 4591 DEBUGFUNC("ixgbe_host_interface_command"); 4592 4593 if (length == 0 || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { 4594 DEBUGOUT1("Buffer length failure buffersize=%d.\n", length); 4595 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4596 } 4597 4598 /* Take management host interface semaphore */ 4599 status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); 4600 if (status) 4601 return status; 4602 4603 status = ixgbe_hic_unlocked(hw, buffer, length, timeout); 4604 if (status) 4605 goto rel_out; 4606 4607 if (!return_data) 4608 goto rel_out; 4609 4610 /* Calculate length in DWORDs */ 4611 dword_len = hdr_size >> 2; 4612 4613 /* first pull in the header so we know the buffer length */ 4614 for (bi = 0; bi < dword_len; bi++) { 4615 buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); 4616 IXGBE_LE32_TO_CPUS(&buffer[bi]); 4617 } 4618 4619 /* If there is any thing in data position pull it in */ 4620 buf_len = ((struct ixgbe_hic_hdr *)buffer)->buf_len; 4621 if (!buf_len) 4622 goto rel_out; 4623 4624 if (length < buf_len + hdr_size) { 4625 DEBUGOUT("Buffer not large enough for reply message.\n"); 4626 status = IXGBE_ERR_HOST_INTERFACE_COMMAND; 4627 goto rel_out; 4628 } 4629 4630 /* Calculate length in DWORDs, add 3 for odd lengths */ 4631 dword_len = (buf_len + 3) >> 2; 4632 4633 /* Pull in the rest of the buffer (bi is where we left off) */ 4634 for (; bi <= dword_len; bi++) { 4635 buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); 4636 IXGBE_LE32_TO_CPUS(&buffer[bi]); 4637 } 4638 4639rel_out: 4640 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); 4641 4642 return status; 4643} 4644 4645/** 4646 * ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware 4647 * @hw: pointer to the HW structure 4648 * @maj: driver version major number 4649 * @min: driver version minor number 4650 * @build: driver version build number 4651 * @sub: driver version sub build number 4652 * 4653 * Sends driver version number to firmware through the manageability 4654 * block. On success return IXGBE_SUCCESS 4655 * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring 4656 * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. 4657 **/ 4658s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min, 4659 u8 build, u8 sub, u16 len, 4660 const char *driver_ver) 4661{ 4662 struct ixgbe_hic_drv_info fw_cmd; 4663 int i; 4664 s32 ret_val = IXGBE_SUCCESS; 4665 4666 DEBUGFUNC("ixgbe_set_fw_drv_ver_generic"); 4667 UNREFERENCED_2PARAMETER(len, driver_ver); 4668 4669 fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO; 4670 fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN; 4671 fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED; 4672 fw_cmd.port_num = (u8)hw->bus.func; 4673 fw_cmd.ver_maj = maj; 4674 fw_cmd.ver_min = min; 4675 fw_cmd.ver_build = build; 4676 fw_cmd.ver_sub = sub; 4677 fw_cmd.hdr.checksum = 0; 4678 fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd, 4679 (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len)); 4680 fw_cmd.pad = 0; 4681 fw_cmd.pad2 = 0; 4682 4683 for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) { 4684 ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd, 4685 sizeof(fw_cmd), 4686 IXGBE_HI_COMMAND_TIMEOUT, 4687 TRUE); 4688 if (ret_val != IXGBE_SUCCESS) 4689 continue; 4690 4691 if (fw_cmd.hdr.cmd_or_resp.ret_status == 4692 FW_CEM_RESP_STATUS_SUCCESS) 4693 ret_val = IXGBE_SUCCESS; 4694 else 4695 ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND; 4696 4697 break; 4698 } 4699 4700 return ret_val; 4701} 4702 4703/** 4704 * ixgbe_set_rxpba_generic - Initialize Rx packet buffer 4705 * @hw: pointer to hardware structure 4706 * @num_pb: number of packet buffers to allocate 4707 * @headroom: reserve n KB of headroom 4708 * @strategy: packet buffer allocation strategy 4709 **/ 4710void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, int num_pb, u32 headroom, 4711 int strategy) 4712{ 4713 u32 pbsize = hw->mac.rx_pb_size; 4714 int i = 0; 4715 u32 rxpktsize, txpktsize, txpbthresh; 4716 4717 /* Reserve headroom */ 4718 pbsize -= headroom; 4719 4720 if (!num_pb) 4721 num_pb = 1; 4722 4723 /* Divide remaining packet buffer space amongst the number of packet 4724 * buffers requested using supplied strategy. 4725 */ 4726 switch (strategy) { 4727 case PBA_STRATEGY_WEIGHTED: 4728 /* ixgbe_dcb_pba_80_48 strategy weight first half of packet 4729 * buffer with 5/8 of the packet buffer space. 4730 */ 4731 rxpktsize = (pbsize * 5) / (num_pb * 4); 4732 pbsize -= rxpktsize * (num_pb / 2); 4733 rxpktsize <<= IXGBE_RXPBSIZE_SHIFT; 4734 for (; i < (num_pb / 2); i++) 4735 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 4736 /* fall through - configure remaining packet buffers */ 4737 case PBA_STRATEGY_EQUAL: 4738 rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT; 4739 for (; i < num_pb; i++) 4740 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 4741 break; 4742 default: 4743 break; 4744 } 4745 4746 /* Only support an equally distributed Tx packet buffer strategy. */ 4747 txpktsize = IXGBE_TXPBSIZE_MAX / num_pb; 4748 txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX; 4749 for (i = 0; i < num_pb; i++) { 4750 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize); 4751 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh); 4752 } 4753 4754 /* Clear unused TCs, if any, to zero buffer size*/ 4755 for (; i < IXGBE_MAX_PB; i++) { 4756 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0); 4757 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0); 4758 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0); 4759 } 4760} 4761 4762/** 4763 * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo 4764 * @hw: pointer to the hardware structure 4765 * 4766 * The 82599 and x540 MACs can experience issues if TX work is still pending 4767 * when a reset occurs. This function prevents this by flushing the PCIe 4768 * buffers on the system. 4769 **/ 4770void ixgbe_clear_tx_pending(struct ixgbe_hw *hw) 4771{ 4772 u32 gcr_ext, hlreg0, i, poll; 4773 u16 value; 4774 4775 /* 4776 * If double reset is not requested then all transactions should 4777 * already be clear and as such there is no work to do 4778 */ 4779 if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED)) 4780 return; 4781 4782 /* 4783 * Set loopback enable to prevent any transmits from being sent 4784 * should the link come up. This assumes that the RXCTRL.RXEN bit 4785 * has already been cleared. 4786 */ 4787 hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0); 4788 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK); 4789 4790 /* Wait for a last completion before clearing buffers */ 4791 IXGBE_WRITE_FLUSH(hw); 4792 msec_delay(3); 4793 4794 /* 4795 * Before proceeding, make sure that the PCIe block does not have 4796 * transactions pending. 4797 */ 4798 poll = ixgbe_pcie_timeout_poll(hw); 4799 for (i = 0; i < poll; i++) { 4800 usec_delay(100); 4801 value = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_STATUS); 4802 if (IXGBE_REMOVED(hw->hw_addr)) 4803 goto out; 4804 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) 4805 goto out; 4806 } 4807 4808out: 4809 /* initiate cleaning flow for buffers in the PCIe transaction layer */ 4810 gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT); 4811 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, 4812 gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR); 4813 4814 /* Flush all writes and allow 20usec for all transactions to clear */ 4815 IXGBE_WRITE_FLUSH(hw); 4816 usec_delay(20); 4817 4818 /* restore previous register values */ 4819 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext); 4820 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); 4821} 4822 4823/** 4824 * ixgbe_bypass_rw_generic - Bit bang data into by_pass FW 4825 * 4826 * @hw: pointer to hardware structure 4827 * @cmd: Command we send to the FW 4828 * @status: The reply from the FW 4829 * 4830 * Bit-bangs the cmd to the by_pass FW status points to what is returned. 4831 **/ 4832#define IXGBE_BYPASS_BB_WAIT 1 4833s32 ixgbe_bypass_rw_generic(struct ixgbe_hw *hw, u32 cmd, u32 *status) 4834{ 4835 int i; 4836 u32 sck, sdi, sdo, dir_sck, dir_sdi, dir_sdo; 4837 u32 esdp; 4838 4839 if (!status) 4840 return IXGBE_ERR_PARAM; 4841 4842 *status = 0; 4843 4844 /* SDP vary by MAC type */ 4845 switch (hw->mac.type) { 4846 case ixgbe_mac_82599EB: 4847 sck = IXGBE_ESDP_SDP7; 4848 sdi = IXGBE_ESDP_SDP0; 4849 sdo = IXGBE_ESDP_SDP6; 4850 dir_sck = IXGBE_ESDP_SDP7_DIR; 4851 dir_sdi = IXGBE_ESDP_SDP0_DIR; 4852 dir_sdo = IXGBE_ESDP_SDP6_DIR; 4853 break; 4854 case ixgbe_mac_X540: 4855 sck = IXGBE_ESDP_SDP2; 4856 sdi = IXGBE_ESDP_SDP0; 4857 sdo = IXGBE_ESDP_SDP1; 4858 dir_sck = IXGBE_ESDP_SDP2_DIR; 4859 dir_sdi = IXGBE_ESDP_SDP0_DIR; 4860 dir_sdo = IXGBE_ESDP_SDP1_DIR; 4861 break; 4862 default: 4863 return IXGBE_ERR_DEVICE_NOT_SUPPORTED; 4864 } 4865 4866 /* Set SDP pins direction */ 4867 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 4868 esdp |= dir_sck; /* SCK as output */ 4869 esdp |= dir_sdi; /* SDI as output */ 4870 esdp &= ~dir_sdo; /* SDO as input */ 4871 esdp |= sck; 4872 esdp |= sdi; 4873 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4874 IXGBE_WRITE_FLUSH(hw); 4875 msec_delay(IXGBE_BYPASS_BB_WAIT); 4876 4877 /* Generate start condition */ 4878 esdp &= ~sdi; 4879 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4880 IXGBE_WRITE_FLUSH(hw); 4881 msec_delay(IXGBE_BYPASS_BB_WAIT); 4882 4883 esdp &= ~sck; 4884 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4885 IXGBE_WRITE_FLUSH(hw); 4886 msec_delay(IXGBE_BYPASS_BB_WAIT); 4887 4888 /* Clock out the new control word and clock in the status */ 4889 for (i = 0; i < 32; i++) { 4890 if ((cmd >> (31 - i)) & 0x01) { 4891 esdp |= sdi; 4892 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4893 } else { 4894 esdp &= ~sdi; 4895 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4896 } 4897 IXGBE_WRITE_FLUSH(hw); 4898 msec_delay(IXGBE_BYPASS_BB_WAIT); 4899 4900 esdp |= sck; 4901 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4902 IXGBE_WRITE_FLUSH(hw); 4903 msec_delay(IXGBE_BYPASS_BB_WAIT); 4904 4905 esdp &= ~sck; 4906 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4907 IXGBE_WRITE_FLUSH(hw); 4908 msec_delay(IXGBE_BYPASS_BB_WAIT); 4909 4910 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 4911 if (esdp & sdo) 4912 *status = (*status << 1) | 0x01; 4913 else 4914 *status = (*status << 1) | 0x00; 4915 msec_delay(IXGBE_BYPASS_BB_WAIT); 4916 } 4917 4918 /* stop condition */ 4919 esdp |= sck; 4920 esdp &= ~sdi; 4921 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4922 IXGBE_WRITE_FLUSH(hw); 4923 msec_delay(IXGBE_BYPASS_BB_WAIT); 4924 4925 esdp |= sdi; 4926 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 4927 IXGBE_WRITE_FLUSH(hw); 4928 4929 /* set the page bits to match the cmd that the status it belongs to */ 4930 *status = (*status & 0x3fffffff) | (cmd & 0xc0000000); 4931 4932 return IXGBE_SUCCESS; 4933} 4934 4935/** 4936 * ixgbe_bypass_valid_rd_generic - Verify valid return from bit-bang. 4937 * 4938 * If we send a write we can't be sure it took until we can read back 4939 * that same register. It can be a problem as some of the feilds may 4940 * for valid reasons change inbetween the time wrote the register and 4941 * we read it again to verify. So this function check everything we 4942 * can check and then assumes it worked. 4943 * 4944 * @u32 in_reg - The register cmd for the bit-bang read. 4945 * @u32 out_reg - The register returned from a bit-bang read. 4946 **/ 4947bool ixgbe_bypass_valid_rd_generic(u32 in_reg, u32 out_reg) 4948{ 4949 u32 mask; 4950 4951 /* Page must match for all control pages */ 4952 if ((in_reg & BYPASS_PAGE_M) != (out_reg & BYPASS_PAGE_M)) 4953 return FALSE; 4954 4955 switch (in_reg & BYPASS_PAGE_M) { 4956 case BYPASS_PAGE_CTL0: 4957 /* All the following can't change since the last write 4958 * - All the event actions 4959 * - The timeout value 4960 */ 4961 mask = BYPASS_AUX_ON_M | BYPASS_MAIN_ON_M | 4962 BYPASS_MAIN_OFF_M | BYPASS_AUX_OFF_M | 4963 BYPASS_WDTIMEOUT_M | 4964 BYPASS_WDT_VALUE_M; 4965 if ((out_reg & mask) != (in_reg & mask)) 4966 return FALSE; 4967 4968 /* 0x0 is never a valid value for bypass status */ 4969 if (!(out_reg & BYPASS_STATUS_OFF_M)) 4970 return FALSE; 4971 break; 4972 case BYPASS_PAGE_CTL1: 4973 /* All the following can't change since the last write 4974 * - time valid bit 4975 * - time we last sent 4976 */ 4977 mask = BYPASS_CTL1_VALID_M | BYPASS_CTL1_TIME_M; 4978 if ((out_reg & mask) != (in_reg & mask)) 4979 return FALSE; 4980 break; 4981 case BYPASS_PAGE_CTL2: 4982 /* All we can check in this page is control number 4983 * which is already done above. 4984 */ 4985 break; 4986 } 4987 4988 /* We are as sure as we can be return TRUE */ 4989 return TRUE; 4990} 4991 4992/** 4993 * ixgbe_bypass_set_generic - Set a bypass field in the FW CTRL Regiter. 4994 * 4995 * @hw: pointer to hardware structure 4996 * @cmd: The control word we are setting. 4997 * @event: The event we are setting in the FW. This also happens to 4998 * be the mask for the event we are setting (handy) 4999 * @action: The action we set the event to in the FW. This is in a 5000 * bit field that happens to be what we want to put in 5001 * the event spot (also handy) 5002 **/ 5003s32 ixgbe_bypass_set_generic(struct ixgbe_hw *hw, u32 ctrl, u32 event, 5004 u32 action) 5005{ 5006 u32 by_ctl = 0; 5007 u32 cmd, verify; 5008 u32 count = 0; 5009 5010 /* Get current values */ 5011 cmd = ctrl; /* just reading only need control number */ 5012 if (ixgbe_bypass_rw_generic(hw, cmd, &by_ctl)) 5013 return IXGBE_ERR_INVALID_ARGUMENT; 5014 5015 /* Set to new action */ 5016 cmd = (by_ctl & ~event) | BYPASS_WE | action; 5017 if (ixgbe_bypass_rw_generic(hw, cmd, &by_ctl)) 5018 return IXGBE_ERR_INVALID_ARGUMENT; 5019 5020 /* Page 0 force a FW eeprom write which is slow so verify */ 5021 if ((cmd & BYPASS_PAGE_M) == BYPASS_PAGE_CTL0) { 5022 verify = BYPASS_PAGE_CTL0; 5023 do { 5024 if (count++ > 5) 5025 return IXGBE_BYPASS_FW_WRITE_FAILURE; 5026 5027 if (ixgbe_bypass_rw_generic(hw, verify, &by_ctl)) 5028 return IXGBE_ERR_INVALID_ARGUMENT; 5029 } while (!ixgbe_bypass_valid_rd_generic(cmd, by_ctl)); 5030 } else { 5031 /* We have give the FW time for the write to stick */ 5032 msec_delay(100); 5033 } 5034 5035 return IXGBE_SUCCESS; 5036} 5037 5038/** 5039 * ixgbe_bypass_rd_eep_generic - Read the bypass FW eeprom addres. 5040 * 5041 * @hw: pointer to hardware structure 5042 * @addr: The bypass eeprom address to read. 5043 * @value: The 8b of data at the address above. 5044 **/ 5045s32 ixgbe_bypass_rd_eep_generic(struct ixgbe_hw *hw, u32 addr, u8 *value) 5046{ 5047 u32 cmd; 5048 u32 status; 5049 5050 5051 /* send the request */ 5052 cmd = BYPASS_PAGE_CTL2 | BYPASS_WE; 5053 cmd |= (addr << BYPASS_CTL2_OFFSET_SHIFT) & BYPASS_CTL2_OFFSET_M; 5054 if (ixgbe_bypass_rw_generic(hw, cmd, &status)) 5055 return IXGBE_ERR_INVALID_ARGUMENT; 5056 5057 /* We have give the FW time for the write to stick */ 5058 msec_delay(100); 5059 5060 /* now read the results */ 5061 cmd &= ~BYPASS_WE; 5062 if (ixgbe_bypass_rw_generic(hw, cmd, &status)) 5063 return IXGBE_ERR_INVALID_ARGUMENT; 5064 5065 *value = status & BYPASS_CTL2_DATA_M; 5066 5067 return IXGBE_SUCCESS; 5068} 5069 5070 5071/** 5072 * ixgbe_dcb_get_rtrup2tc_generic - read rtrup2tc reg 5073 * @hw: pointer to hardware structure 5074 * @map: pointer to u8 arr for returning map 5075 * 5076 * Read the rtrup2tc HW register and resolve its content into map 5077 **/ 5078void ixgbe_dcb_get_rtrup2tc_generic(struct ixgbe_hw *hw, u8 *map) 5079{ 5080 u32 reg, i; 5081 5082 reg = IXGBE_READ_REG(hw, IXGBE_RTRUP2TC); 5083 for (i = 0; i < IXGBE_DCB_MAX_USER_PRIORITY; i++) 5084 map[i] = IXGBE_RTRUP2TC_UP_MASK & 5085 (reg >> (i * IXGBE_RTRUP2TC_UP_SHIFT)); 5086 return; 5087} 5088 5089void ixgbe_disable_rx_generic(struct ixgbe_hw *hw) 5090{ 5091 u32 pfdtxgswc; 5092 u32 rxctrl; 5093 5094 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 5095 if (rxctrl & IXGBE_RXCTRL_RXEN) { 5096 if (hw->mac.type != ixgbe_mac_82598EB) { 5097 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); 5098 if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) { 5099 pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN; 5100 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); 5101 hw->mac.set_lben = TRUE; 5102 } else { 5103 hw->mac.set_lben = FALSE; 5104 } 5105 } 5106 rxctrl &= ~IXGBE_RXCTRL_RXEN; 5107 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl); 5108 } 5109} 5110 5111void ixgbe_enable_rx_generic(struct ixgbe_hw *hw) 5112{ 5113 u32 pfdtxgswc; 5114 u32 rxctrl; 5115 5116 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 5117 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN)); 5118 5119 if (hw->mac.type != ixgbe_mac_82598EB) { 5120 if (hw->mac.set_lben) { 5121 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); 5122 pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN; 5123 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); 5124 hw->mac.set_lben = FALSE; 5125 } 5126 } 5127} 5128 5129/** 5130 * ixgbe_mng_present - returns TRUE when management capability is present 5131 * @hw: pointer to hardware structure 5132 */ 5133bool ixgbe_mng_present(struct ixgbe_hw *hw) 5134{ 5135 u32 fwsm; 5136 5137 if (hw->mac.type < ixgbe_mac_82599EB) 5138 return FALSE; 5139 5140 fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw)); 5141 fwsm &= IXGBE_FWSM_MODE_MASK; 5142 return fwsm == IXGBE_FWSM_FW_MODE_PT; 5143} 5144 5145/** 5146 * ixgbe_mng_enabled - Is the manageability engine enabled? 5147 * @hw: pointer to hardware structure 5148 * 5149 * Returns TRUE if the manageability engine is enabled. 5150 **/ 5151bool ixgbe_mng_enabled(struct ixgbe_hw *hw) 5152{ 5153 u32 fwsm, manc, factps; 5154 5155 fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw)); 5156 if ((fwsm & IXGBE_FWSM_MODE_MASK) != IXGBE_FWSM_FW_MODE_PT) 5157 return FALSE; 5158 5159 manc = IXGBE_READ_REG(hw, IXGBE_MANC); 5160 if (!(manc & IXGBE_MANC_RCV_TCO_EN)) 5161 return FALSE; 5162 5163 if (hw->mac.type <= ixgbe_mac_X540) { 5164 factps = IXGBE_READ_REG(hw, IXGBE_FACTPS_BY_MAC(hw)); 5165 if (factps & IXGBE_FACTPS_MNGCG) 5166 return FALSE; 5167 } 5168 5169 return TRUE; 5170} 5171 5172/** 5173 * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed 5174 * @hw: pointer to hardware structure 5175 * @speed: new link speed 5176 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 5177 * 5178 * Set the link speed in the MAC and/or PHY register and restarts link. 5179 **/ 5180s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, 5181 ixgbe_link_speed speed, 5182 bool autoneg_wait_to_complete) 5183{ 5184 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; 5185 ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; 5186 s32 status = IXGBE_SUCCESS; 5187 u32 speedcnt = 0; 5188 u32 i = 0; 5189 bool autoneg, link_up = FALSE; 5190 5191 DEBUGFUNC("ixgbe_setup_mac_link_multispeed_fiber"); 5192 5193 /* Mask off requested but non-supported speeds */ 5194 status = ixgbe_get_link_capabilities(hw, &link_speed, &autoneg); 5195 if (status != IXGBE_SUCCESS) 5196 return status; 5197 5198 speed &= link_speed; 5199 5200 /* Try each speed one by one, highest priority first. We do this in 5201 * software because 10Gb fiber doesn't support speed autonegotiation. 5202 */ 5203 if (speed & IXGBE_LINK_SPEED_10GB_FULL) { 5204 speedcnt++; 5205 highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; 5206 5207 /* Set the module link speed */ 5208 switch (hw->phy.media_type) { 5209 case ixgbe_media_type_fiber_fixed: 5210 case ixgbe_media_type_fiber: 5211 ixgbe_set_rate_select_speed(hw, 5212 IXGBE_LINK_SPEED_10GB_FULL); 5213 break; 5214 case ixgbe_media_type_fiber_qsfp: 5215 /* QSFP module automatically detects MAC link speed */ 5216 break; 5217 default: 5218 DEBUGOUT("Unexpected media type.\n"); 5219 break; 5220 } 5221 5222 /* Allow module to change analog characteristics (1G->10G) */ 5223 msec_delay(40); 5224 5225 status = ixgbe_setup_mac_link(hw, 5226 IXGBE_LINK_SPEED_10GB_FULL, 5227 autoneg_wait_to_complete); 5228 if (status != IXGBE_SUCCESS) 5229 return status; 5230 5231 /* Flap the Tx laser if it has not already been done */ 5232 ixgbe_flap_tx_laser(hw); 5233 5234 /* Wait for the controller to acquire link. Per IEEE 802.3ap, 5235 * Section 73.10.2, we may have to wait up to 500ms if KR is 5236 * attempted. 82599 uses the same timing for 10g SFI. 5237 */ 5238 for (i = 0; i < 5; i++) { 5239 /* Wait for the link partner to also set speed */ 5240 msec_delay(100); 5241 5242 /* If we have link, just jump out */ 5243 status = ixgbe_check_link(hw, &link_speed, 5244 &link_up, FALSE); 5245 if (status != IXGBE_SUCCESS) 5246 return status; 5247 5248 if (link_up) 5249 goto out; 5250 } 5251 } 5252 5253 if (speed & IXGBE_LINK_SPEED_1GB_FULL) { 5254 speedcnt++; 5255 if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) 5256 highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; 5257 5258 /* Set the module link speed */ 5259 switch (hw->phy.media_type) { 5260 case ixgbe_media_type_fiber_fixed: 5261 case ixgbe_media_type_fiber: 5262 ixgbe_set_rate_select_speed(hw, 5263 IXGBE_LINK_SPEED_1GB_FULL); 5264 break; 5265 case ixgbe_media_type_fiber_qsfp: 5266 /* QSFP module automatically detects link speed */ 5267 break; 5268 default: 5269 DEBUGOUT("Unexpected media type.\n"); 5270 break; 5271 } 5272 5273 /* Allow module to change analog characteristics (10G->1G) */ 5274 msec_delay(40); 5275 5276 status = ixgbe_setup_mac_link(hw, 5277 IXGBE_LINK_SPEED_1GB_FULL, 5278 autoneg_wait_to_complete); 5279 if (status != IXGBE_SUCCESS) 5280 return status; 5281 5282 /* Flap the Tx laser if it has not already been done */ 5283 ixgbe_flap_tx_laser(hw); 5284 5285 /* Wait for the link partner to also set speed */ 5286 msec_delay(100); 5287 5288 /* If we have link, just jump out */ 5289 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE); 5290 if (status != IXGBE_SUCCESS) 5291 return status; 5292 5293 if (link_up) 5294 goto out; 5295 } 5296 5297 /* We didn't get link. Configure back to the highest speed we tried, 5298 * (if there was more than one). We call ourselves back with just the 5299 * single highest speed that the user requested. 5300 */ 5301 if (speedcnt > 1) 5302 status = ixgbe_setup_mac_link_multispeed_fiber(hw, 5303 highest_link_speed, 5304 autoneg_wait_to_complete); 5305 5306out: 5307 /* Set autoneg_advertised value based on input link speed */ 5308 hw->phy.autoneg_advertised = 0; 5309 5310 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 5311 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; 5312 5313 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 5314 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; 5315 5316 return status; 5317} 5318 5319/** 5320 * ixgbe_set_soft_rate_select_speed - Set module link speed 5321 * @hw: pointer to hardware structure 5322 * @speed: link speed to set 5323 * 5324 * Set module link speed via the soft rate select. 5325 */ 5326void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, 5327 ixgbe_link_speed speed) 5328{ 5329 s32 status; 5330 u8 rs, eeprom_data; 5331 5332 switch (speed) { 5333 case IXGBE_LINK_SPEED_10GB_FULL: 5334 /* one bit mask same as setting on */ 5335 rs = IXGBE_SFF_SOFT_RS_SELECT_10G; 5336 break; 5337 case IXGBE_LINK_SPEED_1GB_FULL: 5338 rs = IXGBE_SFF_SOFT_RS_SELECT_1G; 5339 break; 5340 default: 5341 DEBUGOUT("Invalid fixed module speed\n"); 5342 return; 5343 } 5344 5345 /* Set RS0 */ 5346 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, 5347 IXGBE_I2C_EEPROM_DEV_ADDR2, 5348 &eeprom_data); 5349 if (status) { 5350 DEBUGOUT("Failed to read Rx Rate Select RS0\n"); 5351 goto out; 5352 } 5353 5354 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; 5355 5356 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, 5357 IXGBE_I2C_EEPROM_DEV_ADDR2, 5358 eeprom_data); 5359 if (status) { 5360 DEBUGOUT("Failed to write Rx Rate Select RS0\n"); 5361 goto out; 5362 } 5363 5364 /* Set RS1 */ 5365 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, 5366 IXGBE_I2C_EEPROM_DEV_ADDR2, 5367 &eeprom_data); 5368 if (status) { 5369 DEBUGOUT("Failed to read Rx Rate Select RS1\n"); 5370 goto out; 5371 } 5372 5373 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; 5374 5375 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, 5376 IXGBE_I2C_EEPROM_DEV_ADDR2, 5377 eeprom_data); 5378 if (status) { 5379 DEBUGOUT("Failed to write Rx Rate Select RS1\n"); 5380 goto out; 5381 } 5382out: 5383 return; 5384} 5385