omap3-cm-t3517.dts revision 284090 
1/*
2 * Support for CompuLab CM-T3517
3 */
4/dts-v1/;
5
6#include "am3517.dtsi"
7#include "omap3-cm-t3x.dtsi"
8
9/ {
10	model = "CompuLab CM-T3517";
11	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
12
13	vmmc:  regulator-vmmc {
14                compatible = "regulator-fixed";
15                regulator-name = "vmmc";
16                regulator-min-microvolt = <3300000>;
17                regulator-max-microvolt = <3300000>;
18        };
19
20	wl12xx_vmmc2: wl12xx_vmmc2 {
21		compatible = "regulator-fixed";
22		regulator-name = "vw1271";
23		pinctrl-names = "default";
24		pinctrl-0 = <
25				&wl12xx_wkup_pins
26				&wl12xx_core_pins
27			    >;
28		regulator-min-microvolt = <1800000>;
29		regulator-max-microvolt = <1800000>;
30		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
31		startup-delay-us = <20000>;
32		enable-active-high;
33	};
34
35	wl12xx_vaux2: wl12xx_vaux2 {
36		compatible = "regulator-fixed";
37		regulator-name = "vwl1271_vaux2";
38		regulator-min-microvolt = <1800000>;
39		regulator-max-microvolt = <1800000>;
40	};
41};
42
43&omap3_pmx_wkup {
44
45	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
46		pinctrl-single,pins = <
47			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
48			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4)	/* sys_boot4.gpio_6 */
49		>;
50	};
51};
52
53&omap3_pmx_core {
54
55	phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
56		pinctrl-single,pins = <
57			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4)	/* uart2_tx.gpio_146 */
58		>;
59	};
60
61	phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
62		pinctrl-single,pins = <
63			OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4)	/* uart2_rx.gpio_147 */
64		>;
65	};
66
67	otg_drv_vbus: pinmux_otg_drv_vbus {
68		pinctrl-single,pins = <
69			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
70		>;
71	};
72
73	mmc2_pins: pinmux_mmc2_pins {
74		pinctrl-single,pins = <
75			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
76			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
77			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
78			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
79			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
80			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
81		>;
82	};
83
84	wl12xx_core_pins: pinmux_wl12xx_core_pins {
85		pinctrl-single,pins = <
86			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs5.gpio_56 */
87			OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart2_rts.gpio_145 */
88		>;
89	};
90
91	usb_hub_pins: pinmux_usb_hub_pins {
92		pinctrl-single,pins = <
93			OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 - USB HUB RST */
94		>;
95	};
96};
97
98&hsusb1_phy {
99	pinctrl-names = "default";
100	pinctrl-0 = <&phy1_reset_pins>;
101	reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
102};
103
104&hsusb2_phy {
105	pinctrl-names = "default";
106	pinctrl-0 = <&phy2_reset_pins>;
107	reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
108};
109
110&davinci_emac {
111	status = "okay";
112};
113
114&davinci_mdio {
115	status = "okay";
116};
117
118&am35x_otg_hs {
119	status = "okay";
120	pinctrl-names = "default";
121	pinctrl-0 = <&otg_drv_vbus>;
122};
123
124&mmc1 {
125	vmmc-supply = <&vmmc>;
126};
127
128&mmc2 {
129	pinctrl-names = "default";
130	pinctrl-0 = <&mmc2_pins>;
131	vmmc-supply = <&wl12xx_vmmc2>;
132	vmmc_aux-supply = <&wl12xx_vaux2>;
133	non-removable;
134	bus-width = <4>;
135	cap-power-off-card;
136};
137
138&dss {
139	status = "ok";
140
141	pinctrl-names = "default";
142	pinctrl-0 = <
143		&dss_dpi_pins_common
144		&dss_dpi_pins_cm_t35x
145	>;
146};
147
148