actbl.h revision 281075
1/******************************************************************************
2 *
3 * Name: actbl.h - Basic ACPI Table Definitions
4 *
5 *****************************************************************************/
6
7/*
8 * Copyright (C) 2000 - 2015, Intel Corp.
9 * All rights reserved.
10 *
11 * Redistribution and use in source and binary forms, with or without
12 * modification, are permitted provided that the following conditions
13 * are met:
14 * 1. Redistributions of source code must retain the above copyright
15 *    notice, this list of conditions, and the following disclaimer,
16 *    without modification.
17 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
18 *    substantially similar to the "NO WARRANTY" disclaimer below
19 *    ("Disclaimer") and any redistribution must be conditioned upon
20 *    including a substantially similar Disclaimer requirement for further
21 *    binary redistribution.
22 * 3. Neither the names of the above-listed copyright holders nor the names
23 *    of any contributors may be used to endorse or promote products derived
24 *    from this software without specific prior written permission.
25 *
26 * Alternatively, this software may be distributed under the terms of the
27 * GNU General Public License ("GPL") version 2 as published by the Free
28 * Software Foundation.
29 *
30 * NO WARRANTY
31 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
32 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
33 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
34 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
35 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
36 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
37 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
38 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
39 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
40 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
41 * POSSIBILITY OF SUCH DAMAGES.
42 */
43
44#ifndef __ACTBL_H__
45#define __ACTBL_H__
46
47
48/*******************************************************************************
49 *
50 * Fundamental ACPI tables
51 *
52 * This file contains definitions for the ACPI tables that are directly consumed
53 * by ACPICA. All other tables are consumed by the OS-dependent ACPI-related
54 * device drivers and other OS support code.
55 *
56 * The RSDP and FACS do not use the common ACPI table header. All other ACPI
57 * tables use the header.
58 *
59 ******************************************************************************/
60
61
62/*
63 * Values for description table header signatures for tables defined in this
64 * file. Useful because they make it more difficult to inadvertently type in
65 * the wrong signature.
66 */
67#define ACPI_SIG_DSDT           "DSDT"      /* Differentiated System Description Table */
68#define ACPI_SIG_FADT           "FACP"      /* Fixed ACPI Description Table */
69#define ACPI_SIG_FACS           "FACS"      /* Firmware ACPI Control Structure */
70#define ACPI_SIG_PSDT           "PSDT"      /* Persistent System Description Table */
71#define ACPI_SIG_RSDP           "RSD PTR "  /* Root System Description Pointer */
72#define ACPI_SIG_RSDT           "RSDT"      /* Root System Description Table */
73#define ACPI_SIG_XSDT           "XSDT"      /* Extended  System Description Table */
74#define ACPI_SIG_SSDT           "SSDT"      /* Secondary System Description Table */
75#define ACPI_RSDP_NAME          "RSDP"      /* Short name for RSDP, not signature */
76
77
78/*
79 * All tables and structures must be byte-packed to match the ACPI
80 * specification, since the tables are provided by the system BIOS
81 */
82#pragma pack(1)
83
84/*
85 * Note: C bitfields are not used for this reason:
86 *
87 * "Bitfields are great and easy to read, but unfortunately the C language
88 * does not specify the layout of bitfields in memory, which means they are
89 * essentially useless for dealing with packed data in on-disk formats or
90 * binary wire protocols." (Or ACPI tables and buffers.) "If you ask me,
91 * this decision was a design error in C. Ritchie could have picked an order
92 * and stuck with it." Norman Ramsey.
93 * See http://stackoverflow.com/a/1053662/41661
94 */
95
96
97/*******************************************************************************
98 *
99 * Master ACPI Table Header. This common header is used by all ACPI tables
100 * except the RSDP and FACS.
101 *
102 ******************************************************************************/
103
104typedef struct acpi_table_header
105{
106    char                    Signature[ACPI_NAME_SIZE];          /* ASCII table signature */
107    UINT32                  Length;                             /* Length of table in bytes, including this header */
108    UINT8                   Revision;                           /* ACPI Specification minor version number */
109    UINT8                   Checksum;                           /* To make sum of entire table == 0 */
110    char                    OemId[ACPI_OEM_ID_SIZE];            /* ASCII OEM identification */
111    char                    OemTableId[ACPI_OEM_TABLE_ID_SIZE]; /* ASCII OEM table identification */
112    UINT32                  OemRevision;                        /* OEM revision number */
113    char                    AslCompilerId[ACPI_NAME_SIZE];      /* ASCII ASL compiler vendor ID */
114    UINT32                  AslCompilerRevision;                /* ASL compiler version */
115
116} ACPI_TABLE_HEADER;
117
118
119/*******************************************************************************
120 *
121 * GAS - Generic Address Structure (ACPI 2.0+)
122 *
123 * Note: Since this structure is used in the ACPI tables, it is byte aligned.
124 * If misaligned access is not supported by the hardware, accesses to the
125 * 64-bit Address field must be performed with care.
126 *
127 ******************************************************************************/
128
129typedef struct acpi_generic_address
130{
131    UINT8                   SpaceId;                /* Address space where struct or register exists */
132    UINT8                   BitWidth;               /* Size in bits of given register */
133    UINT8                   BitOffset;              /* Bit offset within the register */
134    UINT8                   AccessWidth;            /* Minimum Access size (ACPI 3.0) */
135    UINT64                  Address;                /* 64-bit address of struct or register */
136
137} ACPI_GENERIC_ADDRESS;
138
139
140/*******************************************************************************
141 *
142 * RSDP - Root System Description Pointer (Signature is "RSD PTR ")
143 *        Version 2
144 *
145 ******************************************************************************/
146
147typedef struct acpi_table_rsdp
148{
149    char                    Signature[8];               /* ACPI signature, contains "RSD PTR " */
150    UINT8                   Checksum;                   /* ACPI 1.0 checksum */
151    char                    OemId[ACPI_OEM_ID_SIZE];    /* OEM identification */
152    UINT8                   Revision;                   /* Must be (0) for ACPI 1.0 or (2) for ACPI 2.0+ */
153    UINT32                  RsdtPhysicalAddress;        /* 32-bit physical address of the RSDT */
154    UINT32                  Length;                     /* Table length in bytes, including header (ACPI 2.0+) */
155    UINT64                  XsdtPhysicalAddress;        /* 64-bit physical address of the XSDT (ACPI 2.0+) */
156    UINT8                   ExtendedChecksum;           /* Checksum of entire table (ACPI 2.0+) */
157    UINT8                   Reserved[3];                /* Reserved, must be zero */
158
159} ACPI_TABLE_RSDP;
160
161/* Standalone struct for the ACPI 1.0 RSDP */
162
163typedef struct acpi_rsdp_common
164{
165    char                    Signature[8];
166    UINT8                   Checksum;
167    char                    OemId[ACPI_OEM_ID_SIZE];
168    UINT8                   Revision;
169    UINT32                  RsdtPhysicalAddress;
170
171} ACPI_RSDP_COMMON;
172
173/* Standalone struct for the extended part of the RSDP (ACPI 2.0+) */
174
175typedef struct acpi_rsdp_extension
176{
177    UINT32                  Length;
178    UINT64                  XsdtPhysicalAddress;
179    UINT8                   ExtendedChecksum;
180    UINT8                   Reserved[3];
181
182} ACPI_RSDP_EXTENSION;
183
184
185/*******************************************************************************
186 *
187 * RSDT/XSDT - Root System Description Tables
188 *             Version 1 (both)
189 *
190 ******************************************************************************/
191
192typedef struct acpi_table_rsdt
193{
194    ACPI_TABLE_HEADER       Header;                 /* Common ACPI table header */
195    UINT32                  TableOffsetEntry[1];    /* Array of pointers to ACPI tables */
196
197} ACPI_TABLE_RSDT;
198
199typedef struct acpi_table_xsdt
200{
201    ACPI_TABLE_HEADER       Header;                 /* Common ACPI table header */
202    UINT64                  TableOffsetEntry[1];    /* Array of pointers to ACPI tables */
203
204} ACPI_TABLE_XSDT;
205
206#define ACPI_RSDT_ENTRY_SIZE        (sizeof (UINT32))
207#define ACPI_XSDT_ENTRY_SIZE        (sizeof (UINT64))
208
209
210/*******************************************************************************
211 *
212 * FACS - Firmware ACPI Control Structure (FACS)
213 *
214 ******************************************************************************/
215
216typedef struct acpi_table_facs
217{
218    char                    Signature[4];           /* ASCII table signature */
219    UINT32                  Length;                 /* Length of structure, in bytes */
220    UINT32                  HardwareSignature;      /* Hardware configuration signature */
221    UINT32                  FirmwareWakingVector;   /* 32-bit physical address of the Firmware Waking Vector */
222    UINT32                  GlobalLock;             /* Global Lock for shared hardware resources */
223    UINT32                  Flags;
224    UINT64                  XFirmwareWakingVector;  /* 64-bit version of the Firmware Waking Vector (ACPI 2.0+) */
225    UINT8                   Version;                /* Version of this table (ACPI 2.0+) */
226    UINT8                   Reserved[3];            /* Reserved, must be zero */
227    UINT32                  OspmFlags;              /* Flags to be set by OSPM (ACPI 4.0) */
228    UINT8                   Reserved1[24];          /* Reserved, must be zero */
229
230} ACPI_TABLE_FACS;
231
232/* Masks for GlobalLock flag field above */
233
234#define ACPI_GLOCK_PENDING          (1)             /* 00: Pending global lock ownership */
235#define ACPI_GLOCK_OWNED            (1<<1)          /* 01: Global lock is owned */
236
237/* Masks for Flags field above  */
238
239#define ACPI_FACS_S4_BIOS_PRESENT   (1)             /* 00: S4BIOS support is present */
240#define ACPI_FACS_64BIT_WAKE        (1<<1)          /* 01: 64-bit wake vector supported (ACPI 4.0) */
241
242/* Masks for OspmFlags field above */
243
244#define ACPI_FACS_64BIT_ENVIRONMENT (1)             /* 00: 64-bit wake environment is required (ACPI 4.0) */
245
246
247/*******************************************************************************
248 *
249 * FADT - Fixed ACPI Description Table (Signature "FACP")
250 *        Version 4
251 *
252 ******************************************************************************/
253
254/* Fields common to all versions of the FADT */
255
256typedef struct acpi_table_fadt
257{
258    ACPI_TABLE_HEADER       Header;             /* Common ACPI table header */
259    UINT32                  Facs;               /* 32-bit physical address of FACS */
260    UINT32                  Dsdt;               /* 32-bit physical address of DSDT */
261    UINT8                   Model;              /* System Interrupt Model (ACPI 1.0) - not used in ACPI 2.0+ */
262    UINT8                   PreferredProfile;   /* Conveys preferred power management profile to OSPM. */
263    UINT16                  SciInterrupt;       /* System vector of SCI interrupt */
264    UINT32                  SmiCommand;         /* 32-bit Port address of SMI command port */
265    UINT8                   AcpiEnable;         /* Value to write to SMI_CMD to enable ACPI */
266    UINT8                   AcpiDisable;        /* Value to write to SMI_CMD to disable ACPI */
267    UINT8                   S4BiosRequest;      /* Value to write to SMI_CMD to enter S4BIOS state */
268    UINT8                   PstateControl;      /* Processor performance state control*/
269    UINT32                  Pm1aEventBlock;     /* 32-bit port address of Power Mgt 1a Event Reg Blk */
270    UINT32                  Pm1bEventBlock;     /* 32-bit port address of Power Mgt 1b Event Reg Blk */
271    UINT32                  Pm1aControlBlock;   /* 32-bit port address of Power Mgt 1a Control Reg Blk */
272    UINT32                  Pm1bControlBlock;   /* 32-bit port address of Power Mgt 1b Control Reg Blk */
273    UINT32                  Pm2ControlBlock;    /* 32-bit port address of Power Mgt 2 Control Reg Blk */
274    UINT32                  PmTimerBlock;       /* 32-bit port address of Power Mgt Timer Ctrl Reg Blk */
275    UINT32                  Gpe0Block;          /* 32-bit port address of General Purpose Event 0 Reg Blk */
276    UINT32                  Gpe1Block;          /* 32-bit port address of General Purpose Event 1 Reg Blk */
277    UINT8                   Pm1EventLength;     /* Byte Length of ports at Pm1xEventBlock */
278    UINT8                   Pm1ControlLength;   /* Byte Length of ports at Pm1xControlBlock */
279    UINT8                   Pm2ControlLength;   /* Byte Length of ports at Pm2ControlBlock */
280    UINT8                   PmTimerLength;      /* Byte Length of ports at PmTimerBlock */
281    UINT8                   Gpe0BlockLength;    /* Byte Length of ports at Gpe0Block */
282    UINT8                   Gpe1BlockLength;    /* Byte Length of ports at Gpe1Block */
283    UINT8                   Gpe1Base;           /* Offset in GPE number space where GPE1 events start */
284    UINT8                   CstControl;         /* Support for the _CST object and C-States change notification */
285    UINT16                  C2Latency;          /* Worst case HW latency to enter/exit C2 state */
286    UINT16                  C3Latency;          /* Worst case HW latency to enter/exit C3 state */
287    UINT16                  FlushSize;          /* Processor memory cache line width, in bytes */
288    UINT16                  FlushStride;        /* Number of flush strides that need to be read */
289    UINT8                   DutyOffset;         /* Processor duty cycle index in processor P_CNT reg */
290    UINT8                   DutyWidth;          /* Processor duty cycle value bit width in P_CNT register */
291    UINT8                   DayAlarm;           /* Index to day-of-month alarm in RTC CMOS RAM */
292    UINT8                   MonthAlarm;         /* Index to month-of-year alarm in RTC CMOS RAM */
293    UINT8                   Century;            /* Index to century in RTC CMOS RAM */
294    UINT16                  BootFlags;          /* IA-PC Boot Architecture Flags (see below for individual flags) */
295    UINT8                   Reserved;           /* Reserved, must be zero */
296    UINT32                  Flags;              /* Miscellaneous flag bits (see below for individual flags) */
297    ACPI_GENERIC_ADDRESS    ResetRegister;      /* 64-bit address of the Reset register */
298    UINT8                   ResetValue;         /* Value to write to the ResetRegister port to reset the system */
299    UINT16                  ArmBootFlags;       /* ARM-Specific Boot Flags (see below for individual flags) (ACPI 5.1) */
300    UINT8                   MinorRevision;      /* FADT Minor Revision (ACPI 5.1) */
301    UINT64                  XFacs;              /* 64-bit physical address of FACS */
302    UINT64                  XDsdt;              /* 64-bit physical address of DSDT */
303    ACPI_GENERIC_ADDRESS    XPm1aEventBlock;    /* 64-bit Extended Power Mgt 1a Event Reg Blk address */
304    ACPI_GENERIC_ADDRESS    XPm1bEventBlock;    /* 64-bit Extended Power Mgt 1b Event Reg Blk address */
305    ACPI_GENERIC_ADDRESS    XPm1aControlBlock;  /* 64-bit Extended Power Mgt 1a Control Reg Blk address */
306    ACPI_GENERIC_ADDRESS    XPm1bControlBlock;  /* 64-bit Extended Power Mgt 1b Control Reg Blk address */
307    ACPI_GENERIC_ADDRESS    XPm2ControlBlock;   /* 64-bit Extended Power Mgt 2 Control Reg Blk address */
308    ACPI_GENERIC_ADDRESS    XPmTimerBlock;      /* 64-bit Extended Power Mgt Timer Ctrl Reg Blk address */
309    ACPI_GENERIC_ADDRESS    XGpe0Block;         /* 64-bit Extended General Purpose Event 0 Reg Blk address */
310    ACPI_GENERIC_ADDRESS    XGpe1Block;         /* 64-bit Extended General Purpose Event 1 Reg Blk address */
311    ACPI_GENERIC_ADDRESS    SleepControl;       /* 64-bit Sleep Control register (ACPI 5.0) */
312    ACPI_GENERIC_ADDRESS    SleepStatus;        /* 64-bit Sleep Status register (ACPI 5.0) */
313
314} ACPI_TABLE_FADT;
315
316
317/* Masks for FADT IA-PC Boot Architecture Flags (boot_flags) [Vx]=Introduced in this FADT revision */
318
319#define ACPI_FADT_LEGACY_DEVICES    (1)         /* 00: [V2] System has LPC or ISA bus devices */
320#define ACPI_FADT_8042              (1<<1)      /* 01: [V3] System has an 8042 controller on port 60/64 */
321#define ACPI_FADT_NO_VGA            (1<<2)      /* 02: [V4] It is not safe to probe for VGA hardware */
322#define ACPI_FADT_NO_MSI            (1<<3)      /* 03: [V4] Message Signaled Interrupts (MSI) must not be enabled */
323#define ACPI_FADT_NO_ASPM           (1<<4)      /* 04: [V4] PCIe ASPM control must not be enabled */
324#define ACPI_FADT_NO_CMOS_RTC       (1<<5)      /* 05: [V5] No CMOS real-time clock present */
325
326/* Masks for FADT ARM Boot Architecture Flags (arm_boot_flags) ACPI 5.1 */
327
328#define ACPI_FADT_PSCI_COMPLIANT    (1)         /* 00: [V5+] PSCI 0.2+ is implemented */
329#define ACPI_FADT_PSCI_USE_HVC      (1<<1)      /* 01: [V5+] HVC must be used instead of SMC as the PSCI conduit */
330
331/* Masks for FADT flags */
332
333#define ACPI_FADT_WBINVD            (1)         /* 00: [V1] The WBINVD instruction works properly */
334#define ACPI_FADT_WBINVD_FLUSH      (1<<1)      /* 01: [V1] WBINVD flushes but does not invalidate caches */
335#define ACPI_FADT_C1_SUPPORTED      (1<<2)      /* 02: [V1] All processors support C1 state */
336#define ACPI_FADT_C2_MP_SUPPORTED   (1<<3)      /* 03: [V1] C2 state works on MP system */
337#define ACPI_FADT_POWER_BUTTON      (1<<4)      /* 04: [V1] Power button is handled as a control method device */
338#define ACPI_FADT_SLEEP_BUTTON      (1<<5)      /* 05: [V1] Sleep button is handled as a control method device */
339#define ACPI_FADT_FIXED_RTC         (1<<6)      /* 06: [V1] RTC wakeup status is not in fixed register space */
340#define ACPI_FADT_S4_RTC_WAKE       (1<<7)      /* 07: [V1] RTC alarm can wake system from S4 */
341#define ACPI_FADT_32BIT_TIMER       (1<<8)      /* 08: [V1] ACPI timer width is 32-bit (0=24-bit) */
342#define ACPI_FADT_DOCKING_SUPPORTED (1<<9)      /* 09: [V1] Docking supported */
343#define ACPI_FADT_RESET_REGISTER    (1<<10)     /* 10: [V2] System reset via the FADT RESET_REG supported */
344#define ACPI_FADT_SEALED_CASE       (1<<11)     /* 11: [V3] No internal expansion capabilities and case is sealed */
345#define ACPI_FADT_HEADLESS          (1<<12)     /* 12: [V3] No local video capabilities or local input devices */
346#define ACPI_FADT_SLEEP_TYPE        (1<<13)     /* 13: [V3] Must execute native instruction after writing  SLP_TYPx register */
347#define ACPI_FADT_PCI_EXPRESS_WAKE  (1<<14)     /* 14: [V4] System supports PCIEXP_WAKE (STS/EN) bits (ACPI 3.0) */
348#define ACPI_FADT_PLATFORM_CLOCK    (1<<15)     /* 15: [V4] OSPM should use platform-provided timer (ACPI 3.0) */
349#define ACPI_FADT_S4_RTC_VALID      (1<<16)     /* 16: [V4] Contents of RTC_STS valid after S4 wake (ACPI 3.0) */
350#define ACPI_FADT_REMOTE_POWER_ON   (1<<17)     /* 17: [V4] System is compatible with remote power on (ACPI 3.0) */
351#define ACPI_FADT_APIC_CLUSTER      (1<<18)     /* 18: [V4] All local APICs must use cluster model (ACPI 3.0) */
352#define ACPI_FADT_APIC_PHYSICAL     (1<<19)     /* 19: [V4] All local xAPICs must use physical dest mode (ACPI 3.0) */
353#define ACPI_FADT_HW_REDUCED        (1<<20)     /* 20: [V5] ACPI hardware is not implemented (ACPI 5.0) */
354#define ACPI_FADT_LOW_POWER_S0      (1<<21)     /* 21: [V5] S0 power savings are equal or better than S3 (ACPI 5.0) */
355
356
357/* Values for PreferredProfile (Preferred Power Management Profiles) */
358
359enum AcpiPreferredPmProfiles
360{
361    PM_UNSPECIFIED          = 0,
362    PM_DESKTOP              = 1,
363    PM_MOBILE               = 2,
364    PM_WORKSTATION          = 3,
365    PM_ENTERPRISE_SERVER    = 4,
366    PM_SOHO_SERVER          = 5,
367    PM_APPLIANCE_PC         = 6,
368    PM_PERFORMANCE_SERVER   = 7,
369    PM_TABLET               = 8
370};
371
372/* Values for SleepStatus and SleepControl registers (V5 FADT) */
373
374#define ACPI_X_WAKE_STATUS          0x80
375#define ACPI_X_SLEEP_TYPE_MASK      0x1C
376#define ACPI_X_SLEEP_TYPE_POSITION  0x02
377#define ACPI_X_SLEEP_ENABLE         0x20
378
379
380/* Reset to default packing */
381
382#pragma pack()
383
384
385/*
386 * Internal table-related structures
387 */
388typedef union acpi_name_union
389{
390    UINT32                          Integer;
391    char                            Ascii[4];
392
393} ACPI_NAME_UNION;
394
395
396/* Internal ACPI Table Descriptor. One per ACPI table. */
397
398typedef struct acpi_table_desc
399{
400    ACPI_PHYSICAL_ADDRESS           Address;
401    ACPI_TABLE_HEADER               *Pointer;
402    UINT32                          Length;     /* Length fixed at 32 bits (fixed in table header) */
403    ACPI_NAME_UNION                 Signature;
404    ACPI_OWNER_ID                   OwnerId;
405    UINT8                           Flags;
406
407} ACPI_TABLE_DESC;
408
409/* Masks for Flags field above */
410
411#define ACPI_TABLE_ORIGIN_EXTERNAL_VIRTUAL  (0) /* Virtual address, external maintained */
412#define ACPI_TABLE_ORIGIN_INTERNAL_PHYSICAL (1) /* Physical address, internally mapped */
413#define ACPI_TABLE_ORIGIN_INTERNAL_VIRTUAL  (2) /* Virtual address, internallly allocated */
414#define ACPI_TABLE_ORIGIN_MASK              (3)
415#define ACPI_TABLE_IS_LOADED                (8)
416
417
418/*
419 * Get the remaining ACPI tables
420 */
421#include <contrib/dev/acpica/include/actbl1.h>
422#include <contrib/dev/acpica/include/actbl2.h>
423#include <contrib/dev/acpica/include/actbl3.h>
424
425/* Macros used to generate offsets to specific table fields */
426
427#define ACPI_FADT_OFFSET(f)             (UINT16) ACPI_OFFSET (ACPI_TABLE_FADT, f)
428
429/*
430 * Sizes of the various flavors of FADT. We need to look closely
431 * at the FADT length because the version number essentially tells
432 * us nothing because of many BIOS bugs where the version does not
433 * match the expected length. In other words, the length of the
434 * FADT is the bottom line as to what the version really is.
435 *
436 * For reference, the values below are as follows:
437 *     FADT V1  size: 0x074
438 *     FADT V2  size: 0x084
439 *     FADT V3  size: 0x0F4
440 *     FADT V4  size: 0x0F4
441 *     FADT V5  size: 0x10C
442 */
443#define ACPI_FADT_V1_SIZE       (UINT32) (ACPI_FADT_OFFSET (Flags) + 4)
444#define ACPI_FADT_V2_SIZE       (UINT32) (ACPI_FADT_OFFSET (MinorRevision) + 1)
445#define ACPI_FADT_V3_SIZE       (UINT32) (ACPI_FADT_OFFSET (SleepControl))
446#define ACPI_FADT_V5_SIZE       (UINT32) (sizeof (ACPI_TABLE_FADT))
447
448#endif /* __ACTBL_H__ */
449