ti_sdhci.c revision 318198
1/*- 2 * Copyright (c) 2013 Ian Lepore <ian@freebsd.org> 3 * Copyright (c) 2011 Ben Gray <ben.r.gray@gmail.com>. 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 18 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 25 * SUCH DAMAGE. 26 * 27 */ 28#include <sys/cdefs.h> 29__FBSDID("$FreeBSD: stable/10/sys/arm/ti/ti_sdhci.c 318198 2017-05-11 21:01:02Z marius $"); 30 31#include <sys/param.h> 32#include <sys/systm.h> 33#include <sys/bus.h> 34#include <sys/gpio.h> 35#include <sys/kernel.h> 36#include <sys/malloc.h> 37#include <sys/module.h> 38#include <sys/resource.h> 39#include <sys/rman.h> 40#include <sys/sysctl.h> 41#include <sys/taskqueue.h> 42 43#include <machine/bus.h> 44#include <machine/resource.h> 45#include <machine/intr.h> 46 47#include <dev/fdt/fdt_common.h> 48#include <dev/ofw/ofw_bus.h> 49#include <dev/ofw/ofw_bus_subr.h> 50 51#include <dev/mmc/bridge.h> 52#include <dev/mmc/mmcreg.h> 53#include <dev/mmc/mmcbrvar.h> 54 55#include <dev/sdhci/sdhci.h> 56#include "sdhci_if.h" 57 58#include <arm/ti/ti_cpuid.h> 59#include <arm/ti/ti_prcm.h> 60#include "gpio_if.h" 61 62struct ti_sdhci_softc { 63 device_t dev; 64 device_t gpio_dev; 65 struct resource * mem_res; 66 struct resource * irq_res; 67 void * intr_cookie; 68 struct sdhci_slot slot; 69 uint32_t mmchs_device_id; 70 uint32_t mmchs_reg_off; 71 uint32_t sdhci_reg_off; 72 uint32_t baseclk_hz; 73 uint32_t wp_gpio_pin; 74 uint32_t cmd_and_mode; 75 uint32_t sdhci_clkdiv; 76 boolean_t disable_highspeed; 77 boolean_t force_card_present; 78}; 79 80/* 81 * Table of supported FDT compat strings. 82 * 83 * Note that "ti,mmchs" is our own invention, and should be phased out in favor 84 * of the documented names. 85 * 86 * Note that vendor Beaglebone dtsi files use "ti,omap3-hsmmc" for the am335x. 87 */ 88static struct ofw_compat_data compat_data[] = { 89 {"ti,omap3-hsmmc", 1}, 90 {"ti,omap4-hsmmc", 1}, 91 {"ti,mmchs", 1}, 92 {NULL, 0}, 93}; 94 95/* 96 * The MMCHS hardware has a few control and status registers at the beginning of 97 * the device's memory map, followed by the standard sdhci register block. 98 * Different SoCs have the register blocks at different offsets from the 99 * beginning of the device. Define some constants to map out the registers we 100 * access, and the various per-SoC offsets. The SDHCI_REG_OFFSET is how far 101 * beyond the MMCHS block the SDHCI block is found; it's the same on all SoCs. 102 */ 103#define OMAP3_MMCHS_REG_OFFSET 0x000 104#define OMAP4_MMCHS_REG_OFFSET 0x100 105#define AM335X_MMCHS_REG_OFFSET 0x100 106#define SDHCI_REG_OFFSET 0x100 107 108#define MMCHS_SYSCONFIG 0x010 109#define MMCHS_SYSCONFIG_RESET (1 << 1) 110#define MMCHS_SYSSTATUS 0x014 111#define MMCHS_SYSSTATUS_RESETDONE (1 << 0) 112#define MMCHS_CON 0x02C 113#define MMCHS_CON_DW8 (1 << 5) 114#define MMCHS_CON_DVAL_8_4MS (3 << 9) 115#define MMCHS_CON_OD (1 << 0) 116#define MMCHS_SYSCTL 0x12C 117#define MMCHS_SYSCTL_CLKD_MASK 0x3FF 118#define MMCHS_SYSCTL_CLKD_SHIFT 6 119#define MMCHS_SD_CAPA 0x140 120#define MMCHS_SD_CAPA_VS18 (1 << 26) 121#define MMCHS_SD_CAPA_VS30 (1 << 25) 122#define MMCHS_SD_CAPA_VS33 (1 << 24) 123 124static inline uint32_t 125ti_mmchs_read_4(struct ti_sdhci_softc *sc, bus_size_t off) 126{ 127 128 return (bus_read_4(sc->mem_res, off + sc->mmchs_reg_off)); 129} 130 131static inline void 132ti_mmchs_write_4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) 133{ 134 135 bus_write_4(sc->mem_res, off + sc->mmchs_reg_off, val); 136} 137 138static inline uint32_t 139RD4(struct ti_sdhci_softc *sc, bus_size_t off) 140{ 141 142 return (bus_read_4(sc->mem_res, off + sc->sdhci_reg_off)); 143} 144 145static inline void 146WR4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) 147{ 148 149 bus_write_4(sc->mem_res, off + sc->sdhci_reg_off, val); 150} 151 152static uint8_t 153ti_sdhci_read_1(device_t dev, struct sdhci_slot *slot, bus_size_t off) 154{ 155 struct ti_sdhci_softc *sc = device_get_softc(dev); 156 157 return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xff); 158} 159 160static uint16_t 161ti_sdhci_read_2(device_t dev, struct sdhci_slot *slot, bus_size_t off) 162{ 163 struct ti_sdhci_softc *sc = device_get_softc(dev); 164 uint32_t clkdiv, val32; 165 166 /* 167 * The MMCHS hardware has a non-standard interpretation of the sdclock 168 * divisor bits. It uses the same bit positions as SDHCI 3.0 (15..6) 169 * but doesn't split them into low:high fields. Instead they're a 170 * single number in the range 0..1023 and the number is exactly the 171 * clock divisor (with 0 and 1 both meaning divide by 1). The SDHCI 172 * driver code expects a v2.0 or v3.0 divisor. The shifting and masking 173 * here extracts the MMCHS representation from the hardware word, cleans 174 * those bits out, applies the 2N adjustment, and plugs the result into 175 * the bit positions for the 2.0 or 3.0 divisor in the returned register 176 * value. The ti_sdhci_write_2() routine performs the opposite 177 * transformation when the SDHCI driver writes to the register. 178 */ 179 if (off == SDHCI_CLOCK_CONTROL) { 180 val32 = RD4(sc, SDHCI_CLOCK_CONTROL); 181 clkdiv = ((val32 >> MMCHS_SYSCTL_CLKD_SHIFT) & 182 MMCHS_SYSCTL_CLKD_MASK) / 2; 183 val32 &= ~(MMCHS_SYSCTL_CLKD_MASK << MMCHS_SYSCTL_CLKD_SHIFT); 184 val32 |= (clkdiv & SDHCI_DIVIDER_MASK) << SDHCI_DIVIDER_SHIFT; 185 if (slot->version >= SDHCI_SPEC_300) 186 val32 |= ((clkdiv >> SDHCI_DIVIDER_MASK_LEN) & 187 SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_HI_SHIFT; 188 return (val32 & 0xffff); 189 } 190 191 /* 192 * Standard 32-bit handling of command and transfer mode. 193 */ 194 if (off == SDHCI_TRANSFER_MODE) { 195 return (sc->cmd_and_mode >> 16); 196 } else if (off == SDHCI_COMMAND_FLAGS) { 197 return (sc->cmd_and_mode & 0x0000ffff); 198 } 199 200 return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xffff); 201} 202 203static uint32_t 204ti_sdhci_read_4(device_t dev, struct sdhci_slot *slot, bus_size_t off) 205{ 206 struct ti_sdhci_softc *sc = device_get_softc(dev); 207 uint32_t val32; 208 209 val32 = RD4(sc, off); 210 211 /* 212 * If we need to disallow highspeed mode due to the OMAP4 erratum, strip 213 * that flag from the returned capabilities. 214 */ 215 if (off == SDHCI_CAPABILITIES && sc->disable_highspeed) 216 val32 &= ~SDHCI_CAN_DO_HISPD; 217 218 /* 219 * Force the card-present state if necessary. 220 */ 221 if (off == SDHCI_PRESENT_STATE && sc->force_card_present) 222 val32 |= SDHCI_CARD_PRESENT; 223 224 return (val32); 225} 226 227static void 228ti_sdhci_read_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 229 uint32_t *data, bus_size_t count) 230{ 231 struct ti_sdhci_softc *sc = device_get_softc(dev); 232 233 bus_read_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); 234} 235 236static void 237ti_sdhci_write_1(device_t dev, struct sdhci_slot *slot, bus_size_t off, 238 uint8_t val) 239{ 240 struct ti_sdhci_softc *sc = device_get_softc(dev); 241 uint32_t val32; 242 243 val32 = RD4(sc, off & ~3); 244 val32 &= ~(0xff << (off & 3) * 8); 245 val32 |= (val << (off & 3) * 8); 246 247 WR4(sc, off & ~3, val32); 248} 249 250static void 251ti_sdhci_write_2(device_t dev, struct sdhci_slot *slot, bus_size_t off, 252 uint16_t val) 253{ 254 struct ti_sdhci_softc *sc = device_get_softc(dev); 255 uint32_t clkdiv, val32; 256 257 /* 258 * Translate between the hardware and SDHCI 2.0 or 3.0 representations 259 * of the clock divisor. See the comments in ti_sdhci_read_2() for 260 * details. 261 */ 262 if (off == SDHCI_CLOCK_CONTROL) { 263 clkdiv = (val >> SDHCI_DIVIDER_SHIFT) & SDHCI_DIVIDER_MASK; 264 if (slot->version >= SDHCI_SPEC_300) 265 clkdiv |= ((val >> SDHCI_DIVIDER_HI_SHIFT) & 266 SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_MASK_LEN; 267 clkdiv *= 2; 268 if (clkdiv > MMCHS_SYSCTL_CLKD_MASK) 269 clkdiv = MMCHS_SYSCTL_CLKD_MASK; 270 val32 = RD4(sc, SDHCI_CLOCK_CONTROL); 271 val32 &= 0xffff0000; 272 val32 |= val & ~(MMCHS_SYSCTL_CLKD_MASK << 273 MMCHS_SYSCTL_CLKD_SHIFT); 274 val32 |= clkdiv << MMCHS_SYSCTL_CLKD_SHIFT; 275 WR4(sc, SDHCI_CLOCK_CONTROL, val32); 276 return; 277 } 278 279 /* 280 * Standard 32-bit handling of command and transfer mode. 281 */ 282 if (off == SDHCI_TRANSFER_MODE) { 283 sc->cmd_and_mode = (sc->cmd_and_mode & 0xffff0000) | 284 ((uint32_t)val & 0x0000ffff); 285 return; 286 } else if (off == SDHCI_COMMAND_FLAGS) { 287 sc->cmd_and_mode = (sc->cmd_and_mode & 0x0000ffff) | 288 ((uint32_t)val << 16); 289 WR4(sc, SDHCI_TRANSFER_MODE, sc->cmd_and_mode); 290 return; 291 } 292 293 val32 = RD4(sc, off & ~3); 294 val32 &= ~(0xffff << (off & 3) * 8); 295 val32 |= ((val & 0xffff) << (off & 3) * 8); 296 WR4(sc, off & ~3, val32); 297} 298 299static void 300ti_sdhci_write_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 301 uint32_t val) 302{ 303 struct ti_sdhci_softc *sc = device_get_softc(dev); 304 305 WR4(sc, off, val); 306} 307 308static void 309ti_sdhci_write_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 310 uint32_t *data, bus_size_t count) 311{ 312 struct ti_sdhci_softc *sc = device_get_softc(dev); 313 314 bus_write_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); 315} 316 317static void 318ti_sdhci_intr(void *arg) 319{ 320 struct ti_sdhci_softc *sc = arg; 321 322 sdhci_generic_intr(&sc->slot); 323} 324 325static int 326ti_sdhci_update_ios(device_t brdev, device_t reqdev) 327{ 328 struct ti_sdhci_softc *sc = device_get_softc(brdev); 329 struct sdhci_slot *slot; 330 struct mmc_ios *ios; 331 uint32_t val32, newval32; 332 333 slot = device_get_ivars(reqdev); 334 ios = &slot->host.ios; 335 336 /* 337 * There is an 8-bit-bus bit in the MMCHS control register which, when 338 * set, overrides the 1 vs 4 bit setting in the standard SDHCI 339 * registers. Set that bit first according to whether an 8-bit bus is 340 * requested, then let the standard driver handle everything else. 341 */ 342 val32 = ti_mmchs_read_4(sc, MMCHS_CON); 343 newval32 = val32; 344 345 if (ios->bus_width == bus_width_8) 346 newval32 |= MMCHS_CON_DW8; 347 else 348 newval32 &= ~MMCHS_CON_DW8; 349 350 if (ios->bus_mode == opendrain) 351 newval32 |= MMCHS_CON_OD; 352 else /* if (ios->bus_mode == pushpull) */ 353 newval32 &= ~MMCHS_CON_OD; 354 355 if (newval32 != val32) 356 ti_mmchs_write_4(sc, MMCHS_CON, newval32); 357 358 return (sdhci_generic_update_ios(brdev, reqdev)); 359} 360 361static int 362ti_sdhci_get_ro(device_t brdev, device_t reqdev) 363{ 364 struct ti_sdhci_softc *sc = device_get_softc(brdev); 365 unsigned int readonly = 0; 366 367 /* If a gpio pin is configured, read it. */ 368 if (sc->gpio_dev != NULL) { 369 GPIO_PIN_GET(sc->gpio_dev, sc->wp_gpio_pin, &readonly); 370 } 371 372 return (readonly); 373} 374 375static int 376ti_sdhci_detach(device_t dev) 377{ 378 379 return (EBUSY); 380} 381 382static void 383ti_sdhci_hw_init(device_t dev) 384{ 385 struct ti_sdhci_softc *sc = device_get_softc(dev); 386 clk_ident_t clk; 387 uint32_t regval; 388 unsigned long timeout; 389 390 /* Enable the controller and interface/functional clocks */ 391 clk = MMC0_CLK + sc->mmchs_device_id; 392 if (ti_prcm_clk_enable(clk) != 0) { 393 device_printf(dev, "Error: failed to enable MMC clock\n"); 394 return; 395 } 396 397 /* Get the frequency of the source clock */ 398 if (ti_prcm_clk_get_source_freq(clk, &sc->baseclk_hz) != 0) { 399 device_printf(dev, "Error: failed to get source clock freq\n"); 400 return; 401 } 402 403 /* Issue a softreset to the controller */ 404 ti_mmchs_write_4(sc, MMCHS_SYSCONFIG, MMCHS_SYSCONFIG_RESET); 405 timeout = 1000; 406 while (!(ti_mmchs_read_4(sc, MMCHS_SYSSTATUS) & 407 MMCHS_SYSSTATUS_RESETDONE)) { 408 if (--timeout == 0) { 409 device_printf(dev, 410 "Error: Controller reset operation timed out\n"); 411 break; 412 } 413 DELAY(100); 414 } 415 416 /* 417 * Reset the command and data state machines and also other aspects of 418 * the controller such as bus clock and power. 419 * 420 * If we read the software reset register too fast after writing it we 421 * can get back a zero that means the reset hasn't started yet rather 422 * than that the reset is complete. Per TI recommendations, work around 423 * it by reading until we see the reset bit asserted, then read until 424 * it's clear. We also set the SDHCI_QUIRK_WAITFOR_RESET_ASSERTED quirk 425 * so that the main sdhci driver uses this same logic in its resets. 426 */ 427 ti_sdhci_write_1(dev, NULL, SDHCI_SOFTWARE_RESET, SDHCI_RESET_ALL); 428 timeout = 10000; 429 while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & 430 SDHCI_RESET_ALL) != SDHCI_RESET_ALL) { 431 if (--timeout == 0) { 432 break; 433 } 434 DELAY(1); 435 } 436 timeout = 10000; 437 while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & 438 SDHCI_RESET_ALL)) { 439 if (--timeout == 0) { 440 device_printf(dev, 441 "Error: Software reset operation timed out\n"); 442 break; 443 } 444 DELAY(100); 445 } 446 447 /* 448 * The attach() routine has examined fdt data and set flags in 449 * slot.host.caps to reflect what voltages we can handle. Set those 450 * values in the CAPA register. The manual says that these values can 451 * only be set once, "before initialization" whatever that means, and 452 * that they survive a reset. So maybe doing this will be a no-op if 453 * u-boot has already initialized the hardware. 454 */ 455 regval = ti_mmchs_read_4(sc, MMCHS_SD_CAPA); 456 if (sc->slot.host.caps & MMC_OCR_LOW_VOLTAGE) 457 regval |= MMCHS_SD_CAPA_VS18; 458 if (sc->slot.host.caps & (MMC_OCR_290_300 | MMC_OCR_300_310)) 459 regval |= MMCHS_SD_CAPA_VS30; 460 ti_mmchs_write_4(sc, MMCHS_SD_CAPA, regval); 461 462 /* Set initial host configuration (1-bit, std speed, pwr off). */ 463 ti_sdhci_write_1(dev, NULL, SDHCI_HOST_CONTROL, 0); 464 ti_sdhci_write_1(dev, NULL, SDHCI_POWER_CONTROL, 0); 465 466 /* Set the initial controller configuration. */ 467 ti_mmchs_write_4(sc, MMCHS_CON, MMCHS_CON_DVAL_8_4MS); 468} 469 470static int 471ti_sdhci_attach(device_t dev) 472{ 473 struct ti_sdhci_softc *sc = device_get_softc(dev); 474 int rid, err; 475 pcell_t prop; 476 phandle_t node; 477 478 sc->dev = dev; 479 480 /* 481 * Get the MMCHS device id from FDT. If it's not there use the newbus 482 * unit number (which will work as long as the devices are in order and 483 * none are skipped in the fdt). Note that this is a property we made 484 * up and added in freebsd, it doesn't exist in the published bindings. 485 */ 486 node = ofw_bus_get_node(dev); 487 if ((OF_getprop(node, "mmchs-device-id", &prop, sizeof(prop))) <= 0) { 488 sc->mmchs_device_id = device_get_unit(dev); 489 device_printf(dev, "missing mmchs-device-id attribute in FDT, " 490 "using unit number (%d)", sc->mmchs_device_id); 491 } else 492 sc->mmchs_device_id = fdt32_to_cpu(prop); 493 494 /* 495 * The hardware can inherently do dual-voltage (1p8v, 3p0v) on the first 496 * device, and only 1p8v on other devices unless an external transceiver 497 * is used. The only way we could know about a transceiver is fdt data. 498 * Note that we have to do this before calling ti_sdhci_hw_init() so 499 * that it can set the right values in the CAPA register, which can only 500 * be done once and never reset. 501 */ 502 sc->slot.host.caps |= MMC_OCR_LOW_VOLTAGE; 503 if (sc->mmchs_device_id == 0 || OF_hasprop(node, "ti,dual-volt")) { 504 sc->slot.host.caps |= MMC_OCR_290_300 | MMC_OCR_300_310; 505 } 506 507 /* 508 * See if we've got a GPIO-based write detect pin. This is not the 509 * standard documented property for this, we added it in freebsd. 510 */ 511 if ((OF_getprop(node, "mmchs-wp-gpio-pin", &prop, sizeof(prop))) <= 0) 512 sc->wp_gpio_pin = 0xffffffff; 513 else 514 sc->wp_gpio_pin = fdt32_to_cpu(prop); 515 516 if (sc->wp_gpio_pin != 0xffffffff) { 517 sc->gpio_dev = devclass_get_device(devclass_find("gpio"), 0); 518 if (sc->gpio_dev == NULL) 519 device_printf(dev, "Error: No GPIO device, " 520 "Write Protect pin will not function\n"); 521 else 522 GPIO_PIN_SETFLAGS(sc->gpio_dev, sc->wp_gpio_pin, 523 GPIO_PIN_INPUT); 524 } 525 526 /* 527 * Set the offset from the device's memory start to the MMCHS registers. 528 * Also for OMAP4 disable high speed mode due to erratum ID i626. 529 */ 530 if (ti_chip() == CHIP_OMAP_3) 531 sc->mmchs_reg_off = OMAP3_MMCHS_REG_OFFSET; 532 else if (ti_chip() == CHIP_OMAP_4) { 533 sc->mmchs_reg_off = OMAP4_MMCHS_REG_OFFSET; 534 sc->disable_highspeed = true; 535 } else if (ti_chip() == CHIP_AM335X) 536 sc->mmchs_reg_off = AM335X_MMCHS_REG_OFFSET; 537 else 538 panic("Unknown OMAP device\n"); 539 540 /* 541 * The standard SDHCI registers are at a fixed offset (the same on all 542 * SoCs) beyond the MMCHS registers. 543 */ 544 sc->sdhci_reg_off = sc->mmchs_reg_off + SDHCI_REG_OFFSET; 545 546 /* Resource setup. */ 547 rid = 0; 548 sc->mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 549 RF_ACTIVE); 550 if (!sc->mem_res) { 551 device_printf(dev, "cannot allocate memory window\n"); 552 err = ENXIO; 553 goto fail; 554 } 555 556 rid = 0; 557 sc->irq_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 558 RF_ACTIVE); 559 if (!sc->irq_res) { 560 device_printf(dev, "cannot allocate interrupt\n"); 561 err = ENXIO; 562 goto fail; 563 } 564 565 if (bus_setup_intr(dev, sc->irq_res, INTR_TYPE_BIO | INTR_MPSAFE, 566 NULL, ti_sdhci_intr, sc, &sc->intr_cookie)) { 567 device_printf(dev, "cannot setup interrupt handler\n"); 568 err = ENXIO; 569 goto fail; 570 } 571 572 /* Initialise the MMCHS hardware. */ 573 ti_sdhci_hw_init(dev); 574 575 /* 576 * The capabilities register can only express base clock frequencies in 577 * the range of 0-63MHz for a v2.0 controller. Since our clock runs 578 * faster than that, the hardware sets the frequency to zero in the 579 * register. When the register contains zero, the sdhci driver expects 580 * slot.max_clk to already have the right value in it. 581 */ 582 sc->slot.max_clk = sc->baseclk_hz; 583 584 /* 585 * The MMCHS timeout counter is based on the output sdclock. Tell the 586 * sdhci driver to recalculate the timeout clock whenever the output 587 * sdclock frequency changes. 588 */ 589 sc->slot.quirks |= SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK; 590 591 /* 592 * The MMCHS hardware shifts the 136-bit response data (in violation of 593 * the spec), so tell the sdhci driver not to do the same in software. 594 */ 595 sc->slot.quirks |= SDHCI_QUIRK_DONT_SHIFT_RESPONSE; 596 597 /* 598 * Reset bits are broken, have to wait to see the bits asserted 599 * before waiting to see them de-asserted. 600 */ 601 sc->slot.quirks |= SDHCI_QUIRK_WAITFOR_RESET_ASSERTED; 602 603 /* 604 * The controller waits for busy responses. 605 */ 606 sc->slot.quirks |= SDHCI_QUIRK_WAIT_WHILE_BUSY; 607 608 /* 609 * DMA is not really broken, I just haven't implemented it yet. 610 */ 611 sc->slot.quirks |= SDHCI_QUIRK_BROKEN_DMA; 612 613 /* 614 * Set up the hardware and go. Note that this sets many of the 615 * slot.host.* fields, so we have to do this before overriding any of 616 * those values based on fdt data, below. 617 */ 618 sdhci_init_slot(dev, &sc->slot, 0); 619 620 /* 621 * The SDHCI controller doesn't realize it, but we can support 8-bit 622 * even though we're not a v3.0 controller. If there's an fdt bus-width 623 * property, honor it. 624 */ 625 if (OF_getencprop(node, "bus-width", &prop, sizeof(prop)) > 0) { 626 sc->slot.host.caps &= ~(MMC_CAP_4_BIT_DATA | 627 MMC_CAP_8_BIT_DATA); 628 switch (prop) { 629 case 8: 630 sc->slot.host.caps |= MMC_CAP_8_BIT_DATA; 631 /* FALLTHROUGH */ 632 case 4: 633 sc->slot.host.caps |= MMC_CAP_4_BIT_DATA; 634 break; 635 case 1: 636 break; 637 default: 638 device_printf(dev, "Bad bus-width value %u\n", prop); 639 break; 640 } 641 } 642 643 /* 644 * If the slot is flagged with the non-removable property, set our flag 645 * to always force the SDHCI_CARD_PRESENT bit on. 646 */ 647 node = ofw_bus_get_node(dev); 648 if (OF_hasprop(node, "non-removable")) 649 sc->force_card_present = true; 650 651 bus_generic_probe(dev); 652 bus_generic_attach(dev); 653 654 sdhci_start_slot(&sc->slot); 655 656 return (0); 657 658fail: 659 if (sc->intr_cookie) 660 bus_teardown_intr(dev, sc->irq_res, sc->intr_cookie); 661 if (sc->irq_res) 662 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->irq_res); 663 if (sc->mem_res) 664 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->mem_res); 665 666 return (err); 667} 668 669static int 670ti_sdhci_probe(device_t dev) 671{ 672 673 if (!ofw_bus_status_okay(dev)) 674 return (ENXIO); 675 676 if (ofw_bus_search_compatible(dev, compat_data)->ocd_data != 0) { 677 device_set_desc(dev, "TI MMCHS (SDHCI 2.0)"); 678 return (BUS_PROBE_DEFAULT); 679 } 680 681 return (ENXIO); 682} 683 684static device_method_t ti_sdhci_methods[] = { 685 /* Device interface */ 686 DEVMETHOD(device_probe, ti_sdhci_probe), 687 DEVMETHOD(device_attach, ti_sdhci_attach), 688 DEVMETHOD(device_detach, ti_sdhci_detach), 689 690 /* Bus interface */ 691 DEVMETHOD(bus_read_ivar, sdhci_generic_read_ivar), 692 DEVMETHOD(bus_write_ivar, sdhci_generic_write_ivar), 693 694 /* MMC bridge interface */ 695 DEVMETHOD(mmcbr_update_ios, ti_sdhci_update_ios), 696 DEVMETHOD(mmcbr_request, sdhci_generic_request), 697 DEVMETHOD(mmcbr_get_ro, ti_sdhci_get_ro), 698 DEVMETHOD(mmcbr_acquire_host, sdhci_generic_acquire_host), 699 DEVMETHOD(mmcbr_release_host, sdhci_generic_release_host), 700 701 /* SDHCI registers accessors */ 702 DEVMETHOD(sdhci_read_1, ti_sdhci_read_1), 703 DEVMETHOD(sdhci_read_2, ti_sdhci_read_2), 704 DEVMETHOD(sdhci_read_4, ti_sdhci_read_4), 705 DEVMETHOD(sdhci_read_multi_4, ti_sdhci_read_multi_4), 706 DEVMETHOD(sdhci_write_1, ti_sdhci_write_1), 707 DEVMETHOD(sdhci_write_2, ti_sdhci_write_2), 708 DEVMETHOD(sdhci_write_4, ti_sdhci_write_4), 709 DEVMETHOD(sdhci_write_multi_4, ti_sdhci_write_multi_4), 710 711 DEVMETHOD_END 712}; 713 714static devclass_t ti_sdhci_devclass; 715 716static driver_t ti_sdhci_driver = { 717 "sdhci_ti", 718 ti_sdhci_methods, 719 sizeof(struct ti_sdhci_softc), 720}; 721 722DRIVER_MODULE(sdhci_ti, simplebus, ti_sdhci_driver, ti_sdhci_devclass, NULL, 723 NULL); 724MODULE_DEPEND(sdhci_ti, sdhci, 1, 1, 1); 725MMC_DECLARE_BRIDGE(sdhci_ti); 726