snmpd.config revision 310876
1# $FreeBSD: stable/10/etc/snmpd.config 310876 2016-12-30 23:59:43Z ngie $ 2# 3# Example configuration file for bsnmpd(1). 4# 5 6# 7# Set some common variables 8# 9location := "Room 200" 10contact := "sysmeister@example.com" 11system := 1 # FreeBSD 12traphost := localhost 13trapport := 162 14 15# 16# Set the SNMP engine ID. 17# 18# The snmpEngineID object required from the SNMPv3 Framework. If not explicitly set via 19# this configuration file, an ID is assigned based on the value of the 20# kern.hostid variable 21# engine := 0x80:0x10:0x08:0x10:0x80:0x25 22# snmpEngineID = $(engine) 23 24# Change this! 25read := "public" 26# Uncomment begemotSnmpdCommunityString.0.2 below that sets the community 27# string to enable write access. 28write := "geheim" 29trap := "mytrap" 30 31# 32# Declarations for SNMP-USER-BASED-SM-MIB authentication and privacy options 33# 34 35NoAuthProtocol := 1.3.6.1.6.3.10.1.1.1 36HMACMD5AuthProtocol := 1.3.6.1.6.3.10.1.1.2 37HMACSHAAuthProtocol := 1.3.6.1.6.3.10.1.1.3 38NoPrivProtocol := 1.3.6.1.6.3.10.1.2.1 39DESPrivProtocol := 1.3.6.1.6.3.10.1.2.2 40AesCfb128Protocol := 1.3.6.1.6.3.10.1.2.4 41 42# 43# Enumerations from SNMP-FRAMEWORK-MIB 44# 45 46# Security models 47securityModelAny := 0 48securityModelSNMPv1 := 1 49securityModelSNMPv2c := 2 50securityModelUSM := 3 51 52# Message Processing models 53MPmodelSNMPv1 := 0 54MPmodelSNMPv2c := 1 55MPmodelSNMPv3 := 3 56 57# Security levels 58noAuthNoPriv := 1 59authNoPriv := 2 60authPriv := 3 61 62 63# SNMPv3 USM User definition 64# 65# The localized hex password for a user may be obtained by setting SNMPUSER, SNMPPASSWD, 66# SNMPAUTH and SNMPPRIV environment variables to the desired parameters and invoking 67# 'bsnmpget -v 3 -D -K -o verbose' against the running bsnmpd(1). For other 68# usages refer to the bsnmpget(1) manual page. The following lines define a user "bsnmp" 69# with a private password "bsnmptest", localized for the above engine ID. 70# 71#user1 := "bsnmp" 72#user1passwd := 0x22:0x98:0x1a:0x6e:0x39:0x93:0x16:0x5e:0x6a:0x21:0x1b:0xd8:0xa9:0x81:0x31:0x05:0x16:0x33:0x38:0x60 73 74# 75# Configuration 76# 77%snmpd 78begemotSnmpdDebugDumpPdus = 2 79begemotSnmpdDebugSyslogPri = 7 80 81# 82# Set the read and write communities. 83# 84# The default value of the community strings is NULL (note, that this is 85# different from the empty string). This disables both read and write access. 86# To enable read access only the read community string must be set. Setting 87# the write community string enables both read and write access with that 88# string. 89# 90# Be sure to understand the security implications of SNMPv2 - the community 91# strings are readable on the wire! 92# 93begemotSnmpdCommunityString.0.1 = $(read) 94# begemotSnmpdCommunityString.0.2 = $(write) 95begemotSnmpdCommunityDisable = 1 96 97# open standard SNMP ports 98begemotSnmpdPortStatus.0.0.0.0.161 = 1 99 100# open a unix domain socket 101begemotSnmpdLocalPortStatus."/var/run/snmpd.sock" = 1 102begemotSnmpdLocalPortType."/var/run/snmpd.sock" = 4 103 104# send traps to the traphost 105begemotTrapSinkStatus.[$(traphost)].$(trapport) = 4 106begemotTrapSinkVersion.[$(traphost)].$(trapport) = 2 107begemotTrapSinkComm.[$(traphost)].$(trapport) = $(trap) 108 109sysContact = $(contact) 110sysLocation = $(location) 111sysObjectId = 1.3.6.1.4.1.12325.1.1.2.1.$(system) 112 113snmpEnableAuthenTraps = 2 114 115# Uncomment `begemotSnmpdModulePath.".." = ".."' entries below to enable 116# modules 117 118# 119# Bridge module 120# This requires the mibII module. 121# 122#begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so" 123 124# 125# Host resources module 126# This requires the mibII module. 127# 128#begemotSnmpdModulePath."hostres" = "/usr/lib/snmp_hostres.so" 129 130# 131# MIB-2 module 132# 133begemotSnmpdModulePath."mibII" = "/usr/lib/snmp_mibII.so" 134 135# 136# Netgraph module 137# 138#begemotSnmpdModulePath."netgraph" = "/usr/lib/snmp_netgraph.so" 139 140# 141# pf(4) module 142# 143#begemotSnmpdModulePath."pf" = "/usr/lib/snmp_pf.so" 144 145# 146# SNMPv3 Notification Targets 147# 148# begemotSnmpdModulePath."target" = "/usr/lib/snmp_target.so" 149 150# 151# SNMPv3 User-based security module - must be loaded for SNMPv3 USM 152# 153#begemotSnmpdModulePath."usm" = "/usr/lib/snmp_usm.so" 154 155# 156# SNMPv3 View-based Access Control module 157# 158#begemotSnmpdModulePath."vacm" = "/usr/lib/snmp_vacm.so" 159 160# 161# Wireless module 162# This requires the mibII module. 163# 164#begemotSnmpdModulePath."wlan" = "/usr/lib/snmp_wlan.so" 165 166# 167# SNMPv3 USM User definition. 168# 169 170#%usm 171 172# 173# The following block creates a user with name "bsnmp" and sets privacy 174# and encryption options to SHA256 message digests and AES encryption 175# for this user. 176# 177# usmUserStatus.$(engine).$(user1) = 5 178# usmUserAuthProtocol.$(engine).$(user1) = $(HMACSHAAuthProtocol) 179# usmUserAuthKeyChange.$(engine).$(user1) = $(user1passwd) 180# usmUserPrivProtocol.$(engine).$(user1) = $(AesCfb128Protocol) 181# usmUserPrivKeyChange.$(engine).$(user1) = $(user1passwd) 182# usmUserStatus.$(engine).$(user1) = 1 183# 184 185# 186# The following block creates a user with name "public" with no authentication 187# or encryption options. 188# 189# usmUserStatus.$(engine).$(read) = 5 190# usmUserAuthProtocol.$(engine).$(read) = $(NoAuthProtocol) 191# usmUserPrivProtocol.$(engine).$(read) = $(NoPrivProtocol) 192# usmUserStatus.$(engine).$(read) = 1 193# 194 195# 196# Definition of view-based access control entries. 197# 198#%vacm 199 200# Definition of a SNMPv1 group 201# vacmSecurityToGroupStatus.$(securityModelSNMPv1).$(read) = 4 202# vacmGroupName.$(securityModelSNMPv1).$(read) = $(read) 203 204# Definition of SNMPv2 group 205# vacmSecurityToGroupStatus.$(securityModelSNMPv2c).$(write) = 4 206# vacmGroupName.$(securityModelSNMPv2c).$(write) = $(write) 207 208# Definition of SNMPv3 group with users "bsnmp" and "public" 209# vacmSecurityToGroupStatus.$(securityModelUSM).$(user1) = 4 210# vacmGroupName.$(securityModelUSM).$(user1) = $(write) 211# vacmSecurityToGroupStatus.$(securityModelUSM).$(read) = 4 212# vacmGroupName.$(securityModelUSM).$(read) = $(write) 213 214# 215# The OID of the .iso.org.dod.internet subtree 216# 217# internetoid := 1.3.6.1 218# internetoidlen := 4 219 220# 221# Definitions of two views 222# 223# vacmViewTreeFamilyStatus."internet".$(internetoidlen).$(internetoid) = 4 224# vacmViewTreeFamilyStatus."restricted".$(internetoidlen).$(internetoid) = 4 225 226# 227# Access control 228# 229 230# 231# Read-only access for SNMPv1 users 232# 233# vacmAccessStatus.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = 4 234# vacmAccessReadViewName.$(read)."".$(securityModelSNMPv1).$(noAuthNoPriv) = "internet" 235 236# 237# Read-write access for SNMPv2 users 238# 239# vacmAccessStatus.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = 4 240# vacmAccessReadViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 241# vacmAccessWriteViewName.$(write)."".$(securityModelSNMPv2c).$(noAuthNoPriv) = "internet" 242 243# 244# Read-write-notify access for SNMPv3 USM users with noAuthNoPriv 245# 246# vacmAccessStatus.$(write)."".3.$(noAuthNoPriv) = 4 247# vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 248# vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 249# vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(noAuthNoPriv) = "internet" 250 251# 252#Read-write-notify access to restricted for SNMPv3 USM users with authPriv 253# 254# vacmAccessStatus.$(write)."".$(securityModelUSM).$(authPriv) = 4 255# vacmAccessReadViewName.$(write)."".$(securityModelUSM).$(authPriv) = "restricted" 256# vacmAccessWriteViewName.$(write)."".$(securityModelUSM).$(authPriv) = "restricted" 257# vacmAccessNotifyViewName.$(write)."".$(securityModelUSM).$(authPriv) = "restricted" 258 259#%target 260# Send notifications to target tag "test" 261# tag := "test" 262# snmpNotifyRowStatus.$(tag) = 4 263# snmpNotifyTag.$(tag) = $(tag) 264 265# tagremote := "testremote" 266# snmpNotifyRowStatus.$(tagremote) = 4 267# snmpNotifyTag.$(tagremote) = $(tagremote) 268 269# 270# Specify the target parameters for the notifications - send with the credentials 271# of user "bsnmp" 272# 273# snmpTargetParamsRowStatus.$(tag) = 5 274# snmpTargetParamsMPModel.$(tag) = $(MPmodelSNMPv3) 275# snmpTargetParamsSecurityModel.$(tag) = $(securityModelUSM) 276# snmpTargetParamsSecurityName.$(tag) = $(user1) 277# snmpTargetParamsSecurityLevel.$(tag) = $(authPriv) 278# snmpTargetParamsRowStatus.$(tag) = 1 279 280# 281# Define the notifications' target address - port 162 on localhost 282# 283# snmpTargetAddrRowStatus.$(tag) = 5 284# snmpTargetAddrTAddress.$(tag) = 0x7f:0x0:0x0:0x1:0x0:0xa2 285# snmpTargetAddrTagList.$(tag) = "test notification" 286# snmpTargetAddrParams.$(tag) = $(tag) 287# snmpTargetAddrRowStatus.$(tag) = 1 288 289# 290# Define the notifications' target address - port 162 on 10.0.0.1 291# 292# snmpTargetAddrRowStatus.$(tagremote) = 5 293# snmpTargetAddrTAddress.$(tagremote) = 0x0a:0x00:0x00:0x1:0x0:0xa2 294# snmpTargetAddrTagList.$(tagremote) = $(tagremote) 295# snmpTargetAddrParams.$(tagremote) = $(tag) 296# snmpTargetAddrRowStatus.$(tagremote) = 1 297 298# Force a polling rate for the 64-bit interface counters in case 299# the automatic computation is wrong (which may be the case if an interface 300# announces the wrong bit rate via its MIB). 301#%mibII 302#begemotIfForcePoll = 2000 303 304#%netgraph 305#begemotNgControlNodeName = "snmpd" 306