pci/hda/patch_ca0132.c

7  * Based on patch_ca0110.c
182 	int params; /* number of default non-on/off params */
183 	/*effect default values, 1st is on/off. */
623 	 * Currently, this value is always set to 0.0f. However, on Windows,
624 	 * when selecting certain headphone profiles on the new Sound Blaster
625 	 * connect software, the QUERY_SPEAKER_EQ_ADDRESS req on mid 0x80 is
920 	/* De-emphasis filter on DAC-1 disabled/enabled */
922 	/* De-emphasis filter on DAC-2 disabled/enabled */
924 	/* De-emphasis filter on DAC-3 disabled/enabled */
926 	/* High-pass filter on ADC_B disabled/enabled */
928 	/* High-pass filter on ADC_C disabled/enabled */
930 	/* Common mode on Port_A disabled/enabled */
932 	/* Common mode on Port_D disabled/enabled */
934 	/* Impedance for ramp generator on Port_A 16 Ohm/10K Ohm */
936 	/* Impedance for ramp generator on Port_D, 16 Ohm/10K Ohm */
1152 	 * alt_select_in, etc. Only used on desktop codecs for now, because of
3640  * of the on-card LED. It seems to use pin 2 for data, then toggles 3 to on and
3803 	 * I dunno what this actually does, but it stays on until the dsp
3808 	 * Same as above, no clue what it does, but it comes on after the dsp
3909 	/*If Playback effects are on, allow stream some time to flush
4441  * If autodetect is enabled, output will be selected based on jack detection.
4443  * If autodetect is disabled, output will be selected based on selection.
4641  * These are the commands needed to setup output on each of the different card
4870 	 * Although unused on all cards but the AE series, this is always set
5008 		codec_dbg(codec, "%s: on.", __func__);
5035  * If autodetect is enabled, mic will be selected based on jack detection.
5037  * If autodetect is disabled, mic will be selected based on selection.
5087  * Mic detection isn't used, because it's kind of pointless on the SBZ.
5301 	/* based on CrystalVoice state to enable VoiceFX. */
5321 	unsigned int on, tmp, channel_cfg;
5352 		/* If Voice Focus on SBZ, set to two channel. */
5396 	on = (val == 0) ? FLOAT_ZERO : FLOAT_ONE;
5398 				   ca0132_effects[idx].reqs[0], on);
5407  * Turn on/off Playback Enhancements
5455  * Turn on/off CrystalVoice
5491 	if (val) /* on */
5522  * gpio pin 1 is a relay that switches on/off, apparently setting the headphone
5609  * them on the Sound Blaster Z, but they would probably also work on the
6754  * Add a control for selecting channel count on speaker output. Setting this
6755  * allows the DSP to do bass redirection and channel upmixing on surround
6797  * channel on speakers that are set as not being full-range. On configurations
6799  * replacement for X-Bass on configurations with an LFE channel.
7154 		 * header on the card, and aux-in is handled by the DBPro board.
7468 	 * Enable based on jack detect.
7583  * cause of most of the no-audio on startup issues were due to improperly
7685  * does volume control, the only volume control you'll get is through PCM on
7754  * If we never change these, probably only need them on initialization.
7815 	/* Mic 2 setup (not present on desktop cards) */
7958 	 * change colors on the external LED strip connected to the AE-5.
8138 	 * Now, at this point on Windows, an actual stream is setup and
8277 	/* Disable mute on Center/LFE. */
8296  * Setup default parameters for the Sound Blaster Z DSP. A lot more going on
8780 	unsigned int on;
8820 		on = (unsigned int)ca0132_effects[i].reqs[0];
8821 		spec->effects_switch[i] = on ? 1 : 0;
8844 	 * The ZxR doesn't have a front panel header, and it's line-in is on
8859 /* prevents popping noise on shutdown */
9510 	 * re entered is on startup for some reason it triggers a suspend and
9606 	 * Re set the PlayEnhancement switch on a resume event, because the